BERKSHIRE HATHAWAY MARMON FOODSERVICE TECHNOLOGIES PRINCECASTLE NCG9-E... User manual

600-C601 RevB_EN 1/ 15
®
LIMITED WARRANTY
TABLE OF CONTENTS
Product Identification ……………………..............1
Safety Information ………………………................2
Model specification ………………………………….…2
Installation ……………………...............................3
Initial Start-Up …………………….........................4
Seasoning the Cooking Surfaces…..................4
Operating Instructions (Electronic Control)…4
Program Instructions (Electronic Control)…...5
Operating Instructions (Mechanical Control).5
Daily Cleaning……………………...........................6
Spring adjustment…………………….....................7
Exploding View…………………….........................8
Wiring Diagram ……………………...................... 13
Error code table…………………………….. ……… ...15
This product is warranted to be free from defects in material and/or
workmanship for a period of 1 year from date of original installation, not to
exceed 18 months from the date of manufacture.
Any component which proves to be faulty in material and/or workmanship
will be replaced or repaired (at the option of Prince Castle, Inc.) without
cost to the customer for parts and labor. This warranty covers on-location
service (i.e. trip charges and/or mileage). Travel mileage is limited to 100
miles (200 Kilometers) round trip (one trip warranty) from an authorized
service agency or its sub-service agency.
This warranty is subject to the following exceptions/conditions:
• Use of any non-genuine Prince Castle parts voids this warranty.
• All labor shall be performed during regular work hours. Overtime
premium (the incremental amount) will be charged to the customer.
• Damage caused by carelessness, neglect and/or abuse (e.g. dropping,
tampering, or altering parts, equipment damaged in shipment, by fire,
flood or an act of God) is not covered under this warranty.
• All problems due to operation at voltages other than that specified on
equipment nameplates are not covered by this warranty. Conversion to
correct voltage is the customer’s responsibility.
• Normal adjustments as outlined in this manual are not covered under
warranty.
• This equipment must be serviced by Prince Castle Authorized Service
Agency or a Prince Castle Service Technician during the warranty period.
• Wearable items such as (springs, Teflon sheets, bearings) are not
Included under warranty.
OPERATION MANUAL
NCG9&8 Series
Product Identification
Prince Castle LLC (China)
5 floor, Building 8, No. 300 Dingyuan Road, Songjiang District, Shanghai, China, Zip Code 201616
Tel: [phone] www.princecastle.com
DISPLAY
SET BUTTON
PRODUCT 1 &
UPPER ARROW
BUTTON
PRODUCT 2 &
LOWER ARROW
BUTTON
PRODUCT 3 BUTTON
PRODUCT 4
BUTTON
TEMPERATURE
BUTTON/LOGO
TOP HEATER
ON/OFF
INDICATOR
LIGHT (1-4)
HEATING
INDICATOR
LIGHT (TOP)
HEATING
INDICATOR LIGHT
(BOTTOM)
NCG9
NCG8

600-C601 RevB_EN 2/ 15
®
MODEL NO. WIDTH (mm) HEIGHT (mm) DEPTH (mm) VOLTAGE POWER
NCG-9-Ex ©12.6 (320) 22.98 (558) 18.47 (469) 208-240V 2500-3360W
NCG-9-Mx ©12.6 (320) 22.98 (558) 18.47 (469) 208-240V 2200-3000W
NCG-8-x ©11.54 (293) 26.64 (677) 23.17 (588) 208-240V 2500-3360W
120V 1908W
NOTE: Height (mm) is when the top plate is open.
©The specific model number please refer to the nameplate on the unit.
Safety Information
Model Specification
Indicates information important to the proper operation of
the unit. Failure to observe may result in damage to the
equipment and/or severe bodily injury or death.
Indicates information important to the operation of the unit.
Failure to observe may result in damage to the equipment.
This equipment is intended for commercialoccasions and operated by
trained staff. Operation by untrained personnel or those with reduced
physical, sensory or mental capabilities may result in severe injury or
death.
Failure to connect unit to rated power supply may cause damage to
the unit and voids the warranty.
WARNING
This warning is not for EUROPEAN market: This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
This warning is only for EUROPEAN market only: This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.

600-C601 RevB_EN 3/ 15
®
Before using your new equipment, read and understand all the instructions and labels associated with the unit
prior to putting it into operation. Make sure all people associated with its use understand the unit’s operation
and safety before they use the unit.
1. All shipping containers should be checked for freight damage both visible and concealed. This unit has been
tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in
damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.
NOTE: Concealed damage or loss –if damage or loss is not apparent until after equipment is unpacked, a request
for inspection of concealed damage must be made with carrier within 15 days. Be certain to retain all contents plus
external and internal packaging materials for inspection. The carrier will make an inspection and will supply
necessary claim forms.
2. This grill is equipped for the voltage shown on the nameplate. It will operate on alternating current only,
however the specified voltage must be applied.
DO NOT CONNECT THE UNIT TO ANY TYPE OF VOLTAGE OTHER THAN THAT ON THE NAMEPLATE. DOING SO
WILL DAMAGE THE UNIT AND VOID THE WARRANTY.
DAMAGED POWER CORDS MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR SIMILARLY
QUALIFIEDPERSONS IN ORDER TO AVOID A HAZARD.
All electrical connections must be in accordance with local electrical codes and any other applicable codes.
Plug the unit into an applicable electrical receptacle.
To prevent an electric shock hazard this device must be bonded to equipment in close proximity with an
equipotential bonding conductor. This device is equipped with a grounding lug for this purpose and is marked
with the following symbol.
Installation
Installation
Prince Castle reserves the right to change specifications and product design without notice.
Such revisions do not entitle the buyer to corresponding changes, improvements, additions
or replacements for previously purchased equipment.

600-C601 RevB_EN 4/ 15
®
View the platen temperature:
To view the unit’s actual temperature by pressing
the Logo button. The window will display the
platen temperature and the corresponding
indicator light is on. Press the product button
“1”&“2” to view the top and bottom temperature
in turn.
Flat Grill Mode:
Press top heater button, located on the right of
display window, to turn off the top platen and the
top heating indicator light is off simultaneously,
activate the bottom platen only. Press the button
again, top platen is activated accordingly.
Cooking Instructions:
1. Start up the unit by placing the power switch into
the ON position. The heating indicators, located on
the left of window, turn red and the letters “L o” will
display in the window. This indicates the unit is in a
warm-up mode. Press one of number product
buttons and the LED above it will light. When the
preset temperatures of the product button chosen
are reached, the heating indicators will turn green
and the display window will show time.
NOTE: Initial warm-up time is approximately 20 minutes .
2. Place product on the cooking surface and close the
lid.
3. Press the product button for this product and let the
display time countdown to “0” at which time the
unit will beep. To turn off the alarm, press the
product button again.
NOTE: To cancel a program early, just press the product
button and hold for 2 seconds.
4. Raise the lid until it stays put at the proper position
and remove the food. Using a spatula, scrape
residue into the grease tray.
5. Turn the unit off when it is not in use.
NOTE: When not in use it is recommended that the lids be
closed to save energy.
Initial Start-Up
1. Place unit on table
2. Before using the unit for the first time, wipe
down the exterior and toasting area with a damp
cloth.
3. Take to a well ventilated area and heat for
approximately 30 minutes.
4. Brush off any debris from the toasting surface.
NOTE: The grill may emit a small amount of smoke as the cooking
surfaces reach 512°F (266°C). Do not be alarmed, as the smoke is
caused by oils associated with the manufacturing process and will
stop when the burn off is complete.
If the cooking platen is made of carbon steel and it may look blue
because the cooking surface produced oxide film after heating in
production. That is normal, do not affect usage.
Seasoning the Cooking Surfaces
First Time Seasoning
Follow your company/corporate guidelines for
seasoning cooking surface, or
1. Bring the grill to 300°F (149°C) and leave it on
while doing the next three steps.
2. Brush the cooking surfaces with a release agent.
If using an aerosol agent, first apply into a cup
and then brush onto cooking surface.
3. Let sit for 20 minutes, and then wipe clean using
a warm damp cloth.
Daily Seasoning
The grill should not require much seasoning while in
use. In most cases, brushing a light coating of the
release agent in the morning and occasionally
throughout the day will be enough to prevent any
sticking. It is not necessary to brush before grilling
each item.
Operating Instructions (Electronic Control)

600-C601 RevB_EN 5/ 15
®
Program Time and Temperature:
1. Press any number product button and the LED above
it will light, then press “SET” button one time and the
display will read "_ _ _ _." Enter the four-digit security
code sequence: 4, 3, 2, 1.
2. Once the correct sequence has been entered, the
preset temperature of top plate will be displayed, set
the desired temperature with "1” increase or “2"
decrease buttons.
3. Press the “SET” button to save the temperature.
4. Then the preset temperature of bottom plate will be
displayed, set the desired temperature with the "1”
increase or “2" decrease buttons.
5. Press the “SET” button to save the temperature.
6. The preset time will now displayed, set the desired
time with the "1” increase or “2" decrease buttons.
7. Press the “SET” button to save the preset time and
exit programming mode.
8. Press other number product button and repeat Step
1to 7to continue programming.
Resetting to Factory Defaults:
To revert all settings back to the original factory
defaults:
1. Press and hold “SET” button and "1” “2" buttons for
4 seconds.
2. The window will display "FAC." That means to reset
to factory defaults.
NOTE: All previously saved settings are lost upon
resetting the defaults! Use with caution!
Switch between °F and °C & Temperature
Calibration:
1. Press “SET” button one time and the display will
read "_ _ _ _." Enter the four-digit security code
sequence: 2, 3, 4, 1.
2. The window will display “dEGC”or “dEGF”, set the
desired temperature unit with the "1” or “2"
buttons.
3. Press the “SET” button to save the change.
4. The window will now display “OF”, enter top
platen temperature calibration.
NOTE: This process is necessary only when a platen
temperature reading on the grill display varies more
than a few degrees from the reading of a calibrated
pyrometer used to measure the temperature of the
same platen. The grill is calibrated before leaving the
factory so this process should only be necessary on rare
occasions.
5. Set the desired offset value with the "1” increase
or “2" decrease buttons in the front of “OF”. ( offset
= the reading from the pyrometer - display
temperature, it is usually a negative )
6. Press the “SET” button to save the offset value.
7. The window will continue to display “OF”for
bottom platen temperature calibration.
8. Set the desired offset value with the "1” increase
or “2" decrease buttons before “OF”.
9. Press the “SET” button to save the new setting.
Programming Instructions (Electronic Control)
Operating Instructions (Mechanical Control)
Cooking Instructions:
1. Turn the unit on by placing the switch in the ON
position. The HEAT ON indicator will be lit until it
reaches operating temperature. When the unit
reaches operating temperature, the heat indicator
will turn off.
NOTE: Initial warm-up time is approximately 20
minutes.
2. Place product on the cooking surface and close the
lid.
3. After some time raise the lid until it stays put at the
proper position and remove the food. Using a
spatula, scrape residue into the grease tray.
4. Turn the unit off when it is not in use.
NOTE: When not in use it is recommended that the lids be
closed to save energy.
Setting the Temperature:
The thermostat control knob is used to set the
temperature to your requirements. The
maximum set point is 608°F (320°C), the
minimum set point is 122°F (50°C). See Knob
Settings.
Typical Knob Setting
Knob Position Approx. Temp
1122°F / 50°C
2212°F / 100°C
3302°F / 150°C
4392°F / 200°C
5482°F / 250°C
6572°F / 300°C
7608°F / 320°C

600-C601 RevB_EN 6/ 15
®
.
Daily Cleaning
DO NOT IMMERSE OR LET THE UNIT STAND IN
WATER. DO NOT HOSE DOWN THE UNIT. KEEP THE
UNIT AWAY FROM RUNNING WATER.
DO NOT SPLASH THE CONTROL HOUSING!
DO NOT SPLASH THE CONDUIT CONNECTING THE
TOP AND BOTTOM OF THE GRILL!
DO NOT USE ICE ON COOKING SURFACE!
Daily Operating Hours
1. After each cook cycle remove all grease and food
residues from the cooking surface with a spatula. The
spatula should have rounded corners to prevent the
cooking surface from being scratched or marked.
2. Wipe cooking surface with a damp cloth if necessary to
minimize grease buildup. If sticking begins to happen on
a regular basis, apply a light coat of release agent as
described in the “Seasoning the Cooking Surfaces”
section of this manual.
3. Empty grease tray at least daily or as necessary during
high use periods.
Never use pumice, griddle stones, or abrasives on
platen surface.
Never strike the griddle surface with a sharp
instrument or spatula edge.
Abusing surface voids the warranty.
After Hours
1. Press and hold “SET” button for 4 seconds to activate the
cleaning mode. The window will display “COOL” until
both plates cool to 149°C (300°F) and the window
displays “CLN”.
2. While in the clean mode, remove grease by applying
liquid dish detergent( recommend using Ecolab™ Heat
Activated Grill & Toaster Cleaner)to the cooking surfaces
with a sponge or plastic scrubbing pad
NOTE: cooking surfaces are still hot.
3. Rinse surfaces twice with a clean damp sponge or cloth.
4. Repeat as necessary.
5. Apply a light coat of release agent as described in the
“Seasoning the Cooking Surfaces” section of this manual.
6. Use a clean cloth and good nonabrasive cleaner to clean
all non- cooking surfaces including the front displays.
Wipe all surfaces with a soft cloth.
7. Press top heater button to exit cleaning mode.
8. To remove carbon buildup (a black matter resulting from
burnt on food residue, oils, and release agents) from the
cooking surfaces, use an approved carbon removal agent
(aluminum safe) applied in accordance with the
instructions provided with the agent. After this process
the cooking surfaces will need to be re-seasoned
according to the instructions in the “Seasoning the
Cooking Surfaces” section of this manual.
Platen Surface Limited Warranty Exclusions
The grill has been designed to give you many years of cooking reliability and requires minimum maintenance to keep the
surface in its original condition. All platen surfaces are warranted for a period of 1 year against manufacturing defects
to the original owner from the date of installation. This limited warranty is void if it is determined by Prince Castle or
one of its authorized representatives that the platen surface has been misused or abused or subjected to the following
situations:
1. Improperly installed.
2. Incorrect voltage applied to unit allowing the surface to overheat and discolor.
3. The misuse of any instrument or tool which scratches or makes indentations in the surface which could cause
the surface to peel, flake, or chip off.
4. The use of any chemical or abrasive cleaning solution, griddle brick, stone, screen or other cleaning products
which could damage and affect the performance of the platen surface.
5. The neglect of daily routine maintenance to the platen surface.

600-C601 RevB_EN 7/ 15
®
Spring Adjustment
NOTE: The spring setting which holds the top housing in the up position is set at the factory and should
provide many years of use without the need of adjusting.
After an extended period of time the top housing may not maintain its original setting, therefore the spring
tension can be adjusted by loosening and tightening the screws on the back of the unit. The detailed steps as
below:
1. Unscrew the screws marked in circles
with screwdriver and take the cover off.
2. Insert the screwdriver into the hole on the
collar and hold on, then using a hex wrench
(size 3/16), loosen the set screw. To tighten the
spring, turn the screwdriver at a proper angle
following the arrow.(turn in the opposite
direction to loosen the spring), then tighten
the sew screw.
3. Put the cover back and attach the screws.
Note: to get the proper spring pretension force,
may need to repeat the operation one or several
times.

600-C601 RevB_EN 8/ 15
®
Model：NCG9 Platen Assembly
Ite
m
Part No.
Description
Qty
Application
1
600-309
HANDLE, WELDMENT
1
2
76-687
BOLT 5/16-18x1.25
1
3
10-C010
BOLT M6X16
2
4
600-315
SHOULDER BOLT, LINK
1
7
600-310
LINK, LIFT
1
8
600-206
BRKT, ARM, TOP
1
9
600-210
FLANGE BEARING ∅8MM
2
10
CG-066
NUT,HEX CAP,250-20
1
11
76-777
SSCUPSKT 0.3125-
18x0.3125
1
12
600-211
WELDMENT,HOUSING,TO
P
1
13
600-205
BRACKET, AXIS, TOP
1
14
600-221
RETAINING RING
1
15
10-C001
E RING 9 mm
9
1
16
600-203
FLANGE BEARING ∅
12MM
2
17
600-C30001
THERMOSTAT
1
18
600-209
INSULATION,TOP
1
19
600-217
BRKT, HEATER, TOP
2
20
600-C305
PROBE.BOT
1
21
600-200
HEATER,TOP 1400W
1
220V,1400W
600-C052
HEATER,TOP 1100W
1
220V,1100W
22
600-204
PLATEN,TOP,ST,FLAT
1
ST,FLAT
600-C043
PLATEN,TOP,ST,GROOVED
ST,GROOVED
600-207
PLATEN,TOP,AL,FLAT
AL,FLAT
600-C044
PLATEN,TOP,AL,GROOVED
AL,GROOVED
23
600-035
WMT, PLATEN, BOT,ST, F
1
ST,FLAT
600-C041
WMT,PLATEN,BOT,ST,
GROOVED
ST,GROOVED
600-043
WMT, PLATEN, BOT,AL, F
AL,FLAT
600-C042
WMT, PLATEN, BOT,AL,
GROOVED
AL,GROOVED
24
600-037
HEATER ,BOT
BOTTOM,1400W
1
220V,1400W
25
26
27
28
600-038
BRKT, HEATER, BOT
1
26
600-C304
PROBE.TOP
1
27
600-C154
STRIP, GUIDE
1
28
600-C112
BRKT, HI LIMID PROBE
2
29
600-041
INSULATION, BOT
1
4
1
1
30
600-040
BRKT, INSULATION
1
31
600-C205
Flexible Tube 3/4'
1
Exploding View
am

600-C601 RevB_EN 9/ 15
®
Model：NCG9 Base Assembly
Item
Part No.
Description
Qty
Application
1
197-232
FOOT, MOUNTING
4
2
600-413
PANEL, FRONT
1
600-C156
PANEL, FRONT
Mechanical Version
3
600-405
GREASE TRAY
1
4
78-233
SWITCH,ROCKER,DPST,IP65,16A
1
5
6
542-164
GUARD,SWITCH
1
6
600-C303
OVERLAY, DISPLAY
1
7
600-407
PLATE, OVERLAY
1
8
600-C302
MAIN PCB
1
9
600-C194
PLATE, RALAY
1
10
65-058
RELAY
2
11
PM-096
TRANSFORMER
1
12
600-312
COUPLER, HANDLE
1
13
77-082
TERMINAL BLOCK, 5 POS
1
14
10-C003
E RING 15 mm
15
2
15
600-308
SHAFT, SPRING
1
16
600-314
SHOULDER BOLT, MOUNT
1
17
600-311
STOP, LIFT
1
18
600-303
BLOCK, MOUNT, TORSION
2
19
600-302
COVER-SPRING
1
20
600-305
COLLAR, TORSION
1
21
10-C004
SSCUPSKT 0.375-16x1-HX-S
1
22
600-316
TORSION SPRING
1
FOR ALUMIUM PLATEN
600-306
TORSION SPRING
FOR STEEL PLATEN
23
600-C402
SPACER, SPRING
2
FOR ALUMIUM PLATEN
600-307
SPACER, SPRING
FOR STEEL PLATEN
24
600-304
FLANGE BEARING ∅20MM
2
25
301-117
HI-LIMIT THERMOSTAT
1
26
066-045
RELIEF,STRAIN,LIQUID TIGHT
1
27
PM-123A
POWER CORD W/ PLUG
1
CH2-16P
72-381
POWER CORD W/ PLUG
1
IEC309
CG-567A/C
POWER CORD & PLUG
1
NEMA 6-20P
28
600-C300
THERMOSTAT,EGO
1
Not Shown, Mechanical Version
29
071-134-1
INDICATOR LIGHT
1
Not Shown, Mechanical Version

600-C601 RevB_EN 10 / 15
®
Model：NCG8 Platen Assembly
Item
Part No.
Description
Qty
Application
1
600-C186
HANDLE, WELDMENT
1
2
76-687
BOLT 5/16-18x1.25
1
3
10-C010
BOLT M6X16
2
4
600-315
SHOULDER BOLT, LINK
1
5
600-C181
MOUNT, RUBBER
1
6
600-C401
RUBBER,BUFFER
1
7
600-C177
LINK, LIFT
1
8
600-C178
BRKT, ARM, TOP
1
9
600-210
FLANGE BEARING ∅8MM
2
10
CG-066
NUT,HEX CAP,250-20
1
11
76-777
SSCUPSKT 0.3125-18x0.3125
1
12
600-C219
WELDMET,HOUSING,TOP
1
13
600-C179
BRACKET, AXIS, TOP
1
14
600-221
RETAINING RING
1
15
10-C001
E RING 9 mm
1
16
600-203
FLANGE BEARING ∅12MM
2
17
600-C30001
THERMOSTAT
1
18
600-C207
INSULATION,TOP
1
19
600-C203
BRKT, HEATER, TOP
2
20
600-C305
PROBE.BOT
1
21
600-C204-1
HEATER,TOP
1
220V，1300W
600-C204-3
HEATER,TOP
120V，800W
22
600-C202
PLATEN,TOP,ST,FLAT
1
ST,FLAT
600-C214
PLATEN,TOP,ST,GROOVED
ST,GROOVED
600-C216
PLATEN,TOP,AL,FLAT
AL,FLAT
600-C215
PLATEN,TOP,AL,GROOVED
AL,GROOVED
23
600-C196
WMT, PLATEN, BOT,ST, F
1
ST,FLAT
600-C217
WMT, PLATEN, BOT,ST, GROOVED
ST,GROOVED
600-C211
WMT, PLATEN, BOT,AL, F
AL,FLAT
600-C218
WMT, PLATEN, BOT,AL, GROOVED
AL,GROOVED
24
600-C198-1
HEATER, BOT
1
220V，1500W
600-C198-3
HEATER, BOT
120V，1100W
25
600-C197
BRKT, HEATER, BOT
2
26
600-C304
PROBE.TOP
1
27
600-C199
STRIP, GREASE
1
28
600-C112
BRKT, HI LIMID PROBE
1
29
600-C206
INSULATION,BOT
1
30
600-C171
BRKT, INSULATION
4
31
600-C205
Flexible Tube 3/4'
1

600-C601 RevB_EN 11 / 15
®
Model：NCG8 Base Assembly
Item
Part No.
Desription
Qty
Application
1
197-232
FOOT, MOUNTING
4
2
600-C191
WELDMENT,PANEL, FACE
1
3
600-C195
WMT, GREASE TRAY
1
4
78-233
SWITCH,ROCKER,DPST,IP65,16A
1
5
542-164
GUARD,SWITCH
1
6
600-C303
OVERLAY, DISPLAY
1
7
600-407
BACKER, DISPLAY
1
8
600-C302
MAIN PCB
1
9
600-C194
PLATE, RALAY
1
10
65-058
RELAY
2
11
PM-096
TRANSFORMER
1
220V
PM-042
TRANSFORMER
120V
12
600-312
COUPLER, HANDLE
1
13
77-082
TERMINAL BLOCK, 5 POS
1
14
10-C003
E RING 15 mm
15
2
15
600-308
SHAFT, SPRING
1
16
600-314
SHOULDER BOLT, MOUNT
1
17
600-311
STOP, LIFT
1
18
600-303
BLOCK, MOUNT, TORSION
2
19
600-C200
COVER-SPRING
1
20
600-305
COLLAR, TORSION
1
21
10-C004
SSCUPSKT 0.375-16x1-HX-S
1
22
600-306
TORSION SPRING
1
23
600-307
SPACER, SPRING
2
24
600-304
FLANGE BEARING ∅20MM
2
25
301-117
ELECTRIC THERMOSTAT, DBL POLE,
1
26
066-045
RELIEF,STRAIN,LIQUID TIGHT
1
27
PM-123A
POWER CORD W/ PLUG
1
CH2-16P
72-381
POWER CORD W/ PLUG
1
IEC309
CG-567A/C
POWER CORD & PLUG
1
NEMA 6-20P
72-470
POWER CORD & PLUG
1
NEMA 5-30P
28
600-C300
THERMOSTAT,EGO
1
Not Shown, Mechanical Version
29
071-134-1
INDICATOR LIGHT
1
Not Shown, Mechanical Version

600-C601 RevB_EN 12 / 15
®
Model: NCG9&8 Teflon sheet kit (optional):
Note: for safety, please use only this Teflon sheet paper recommended by manufacture.
Model: NCG9&8 heat shield kit (optional):
Item
Part No.
Description
Qty
Application
1
600-C103
HOOK
1
2
600-C104
HOLDER
2
3
600-C107
BRACKET
2
4
600-C114
TOP CLAMP
1
NCG9
600-C101
TOP CLAMP
1
NCG8
5
600-C404
TEFLON SHEET, BLACK 390*300
1
NCG9
600-C406
TEFLON SHEET, BLACK 430*365
1
NCG8
6
600-C403
TEFLON SHEET, BROWN 350*238
1
NCG9
600-C405
TEFLON SHEET, BROWN 470*211
1
NCG8
Item
Part No.
Description
Qty
Application
1
PM-125
SCREW,PNPH,SS,8-32 X3/8
2
2
79-031
WSHR,SPLIT-LOCK S.S.
2
3
600-C048
HEAT SHIELD,NCG9
1
NCG9
600-C049
HEAT SHIELD,NCG8
1
NCG8
4
86-561
HEX NUT
STANDOFF
HEX NUT STANDOFF
2

600-C601 RevB_EN 13 / 15
®
Wiring Diagram
am
Electronical Control Version

600-C601 RevB_EN 14 / 15
®
Mechanical Control Version

600-C601 RevB_EN 15 / 15
®
Error Code
Criteria
Action
E11
The set temperature of the top heating plate is not
reached within 20 minutes.
Check top heater and top Heater
relay
E21
The temperature of the top heating plate exceeds 315
degrees
Check top heater and top Heater
relay
E12
The set temperature of the bottom heating plate is not
reached within 20 minutes.
Check bottom heater and top Heater
relay
E22
The temperature of the bottom heating plate exceeds
315 degrees
Check bottom heater and top Heater
relay
E31
Top RTD fails causing an open circuit (Resistance>=
2810 ohms )
Replace top RTD
E32
Bottom RTD fails causing an open circuit (Resistance>=
2810 ohms )
Replace bottom RTD
E41
Incorrect RTD installed for the top (Resistance <= 922
ohms)
Replace top RTD
E42
Incorrect RTD installed for the bottom (Resistance <=
922 ohms)
Replace bottom RTD
E5
Write operation failed or memory corrupted (CRC)
Replace PCB Board
E6
A button is broken and is always pressed for more than
30 seconds
Check PCB Board and Overlay
Error Code Table
am