Best Choice Products SKY 1845 User manual

zSKU# SKY 1845
ASSEMBLY MANUAL
Charcoal Grill
Revised May2015

The parts and hardware below have been included for assembly:
(F) x 2
(K) x 1
(P) x 4
(V) x 3
(Bolt A) x 14
(aa) x 1
(Tire Nut) x 2
(C) x 1 (D) x 1 (E) x 1(A) x 1
(I) x 1 (J) x 1
(N) x 1 (O) x 2
(S) x 2 (T) x 2
(G) x 1
(L) x 1
(Q) x 1
(W) x 2
(Bolt D) x 4
(bb) x 1
(Bolt E) x 4
(X) x 1
(Bolt B) x 15
(cc) x 1
(Washer) x 2 (Spring) x 1
(Y) x 1
(Bolt C) x15
(dd) x 2
(H) x 2
(M) x 1
(R) x 1
(B) x 1
(U) x 3
(dd) x 3
(Z) x 1
(Steam Cap) x 1
WARNING:
Manufacturer and seller expressly disclaim any and all liability for
personal injury, property damage or loss, whether direct, indirect, or
incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.

Next, slide the lids, part (M) and
part (N), into the holders and
secure using 4 (bolt E’s).
Attach part (T) to the front as-
sembly using 2 (bolt A’s) and then
attach part (S) to part (K) with 2
(bolt B’s) as shown.
Locate the circular hole on the
top of part (K) and attach part (X)
using 3 (bolt C’s). Slide part (Y)
over part (X) with the (spring) and
secure using the (steam cap).
Unscrew the nut located on ther-
mostat, part (CC), slide it in the
designated hole on part (M) and
secure.
Lastly, feed the grease catcher,
part (BB), through the hole on the
inside of part (K), and place part
(AA) on top.
Attach the handles to the lid
by sliding (bolt D) through the
handle, part (O), and then slide
part (P) over (bolt D) as shown.
Lay 3 wood beams (part U)
across part (S) and connect using
(bolt C).
Attach part (Q) and part (R) to
part (L) using 3 (bolt B’s). Attach
part (Z) using a nut from (bolt B).
Note: there is an extra nut added for this
part.
Attach part (W) to part (K) with
4 (bolt B’s). Lay 3 small wood
beams (part V) across and secure
using (bolt C).
10
16 17 18
11 12
13 14 15
Start by sliding part (A) into part
(C), making sure the 2 holes on
the side of both legs are facing
forward (shown with red circles).
This will be the front of the grill.
Using 4 nuts and bolts from (bolt
A) attach part (I) to the assembly
as shown. Do not fully tighten.
Lay part (K) onto the assembly
and secure using 2 (bolt A’s). Do
this to both sides of part (K).
Attach part (B) by sliding it into
part (D) to complete the back of
the grill.
Using 4 nuts and bolts from (bolt
A) attach part (J) to the assembly
as shown. Adjust the assembly
to preference and tighten all nuts
and bolts.
Connect part (L) to part (K) using
6 (bolt B’s).
Next, slide part (F) through one
end of part (E) and wedge
between the front and back
assembly as shown. Repeat this
process on the opposite side.
Next, Slide part (G) into the lower
holes located at the bottom of the
assembly. Slide on the wheels,
part (H) with 2 (washers) and
tighten using 2 (tire nuts).
Connect the bottom of part (L) to
part (I) with (2 bolt Bs).
1
4
7
2
5
8
3
6
9
ASSEMBLY STEPS:
Back
Front
Part Z

Ca Us!
We’re here 7 days a week to help you!
(909)-948-8400
Monday-Friday 5:00am-5:30pm pst
Saturday and Sunday 7:00am-3:30pm pst