Biamp OVO3T User manual

[email protected] support.biamp.com
OVO3T / 5T COMMERCIAL LOUDSPEAKER
INSTALLATION GUIDE
Models
OVO3T
OVO5T
Available in black and white
INSTALLATION CONSIDERATIONS
•This guide covers the installation and initial setup of the OVO3T and OVO5T loudspeakers.
•Be sure to read this manual and the Loudspeaker Safety Guide before installing or using product.
•20-Watts continuous power at 16 Ohm (3T) / 40-Watts continuous power at 16 Ohm (5T).
•The loudspeaker grille is fixed and removing it may cause damage.
•Indoor use only.
DANGER: Installation of loudspeakers should only be performed by
trained and qualied personnel. It is strongly recommended that a
licensed and certied professional structural engineer approve the
mounting design. Severe injury may occur if these products are improperly
installed! All electrical connections must conform to applicable city, county,
state, and national (NEC) electrical codes.
DANGER: It is possible to experience severe electrical shock from a
power amplier. Always make sure that all power ampliers are in the
“OFF" position and unplugged from an AC Mains supply before
performing electrical work.
IMPORTANT: All electrical installation connections for loudspeaker
lines are subject to all applicable governmental building and re
codes. The selection of appropriate electrical hardware to interface
with the loudspeaker lies solely with the installation professional. Biamp
recommends that an appropriately licensed engineer, electrician, or other
qualied professional identify and select the appropriate conduit, ttings, wire,
etc. for the installation.
DANGER: The output power capabilities of audio ampliers present a
danger to installers. To minimize the risk of electric shock from
loudspeaker connecting cables, conrm that the power ampliers are
turned “o" before connecting loudspeaker cable(s) to the loudspeaker or
amplier. Always follow local electrical codes and proper electrical safety
procedures.
The designer must account and compensate for cable losses between the
amplier and the loudspeaker system. Refer to this article on Cornerstone
for more information on cable loss calculations. Please contact the Customer
Support for additional assistance (email: suppor[email protected])
Wire the loudspeaker. Terminate per your local electrical code or requirements.
WARNING: After wiring the amplier(s) to the loudspeaker(s), rst
power-up all devices that are upstream of the amplier, such as
mixers, equalizers, compressor/limiters, etc., before powering-up the
amplier. This is to avoid passing any clicks or pops that may originate in the
upstream devices to the loudspeakers. The amplier should initially be
powered-up with its gain controls turned all the way down. After making sure
that a continuous signal is present, such as a CD playing, slowly raise the level
of the gain controls to establish that the wiring has been installed correctly.
Only then should the loudspeaker be operated at normal output levels.
Rigging and Electrical Safety
Wiring and Electrical Safety

2OVO3T / 5T Installation Guide
OVO3T PRODUCT DESCRIPTION
INCLUDED IN THE BOX
OVO3T
• Loudspeakers with integrated pan / tilt brackets x 2.
• Color-matched rubber surface stands x 2.
Grille
Mounting Bracket
Tap Switch
Access Cover
Mounting Holes
Pan & Tilt
Adjustment Knobs
Optional
Stand

3
OVO3T / 5T Installation Guide
OVO5T
•Loudspeakers with U-brackets x 2.
•Color-matched wedge mounts x 2.
INCLUDED IN THE BOX
OVO5T PRODUCT DESCRIPTION
Tap Switch
Access Cover
Optional Wedge
Mount
Grille
U-Bracket
Pan & Tilt
Adjustment Knob
Pan & Tilt
Adjustment Knob

4OVO3T / 5T Installation Guide
1. Conrm the loudspeaker installation location (the pan / tilt mount may be removed if required).
2. Place the stand on a at surface and set the loudspeaker on the stand.
3. Connect wires and adjust tap settings (see details here).
INSTALLATION
OVO3T Stand Mount Option

5
OVO3T / 5T Installation Guide
1. Conrm the loudspeaker installation location.
2. Unscrew and remove the swivel knob at the top of the speaker to detach the bracket.
3. Connect wires and adjust tap settings (see details here)
4. Use the bracket to mark the hole locations.
5. Attach the bracket to the structure.
OVO3T Wall Mount Option
INSTALLATION CONTINUED
The OVO3T features an integrated pan / tilt bracket (hardware for mounting must be purchased
separately). Adjust the tap setting before installation to save time.

6OVO3T / 5T Installation Guide
6. Reattach the bracket.
7. Adjust the tilt / pan for desired coverage.
8. Connect wires and adjust tap settings (see details here).
+/- 45° Horizontal Pan
in 22.5° increments.
INSTALLATION CONTINUED
OVO3T Wall Mount Option
- 45° Vertical Tilt in 15° increments
(tilts downward only)

7
OVO3T / 5T Installation Guide
1. Conrm the loudspeaker installation location.
2. Unscrew and remove the swivel knob at the top of the speaker to detach the bracket.
3. Use bracket to mark the hole locations.
4. Attach the bracket to the structure.
INSTALLATION CONTINUED
OVO3T Ceiling Mount Option
DANGER: The bracket base
MUST be attached to a
structural component above the
ceiling.
NEVER mount the loudspeaker
directly to ceiling surfaces or
drywall only.

8OVO3T / 5T Installation Guide
5. Reattach the bracket.
6. Adjust the tilt / pan for desired coverage.
7. Connect wires and adjust tap settings (see details here).
INSTALLATION CONTINUED
OVO3T Ceiling Mount Option
+/- 45° Horizontal Pan
in 22.5° increments.
Maximum Tilt is -90° in 22.5°
increments (tilts downward only).

9
OVO3T / 5T Installation Guide
Each OVO5T comes with an attached U-bracket for easy surface installation (installer must provide the
appropriate hardware for the application. Adjust the tap setting before installation to save time.
1. Conrm the loudspeaker installation location.
2. Attach the loudspeaker to the structure or surface using the holes in the U-bracket (hardware not
provided).
NOTE: The U-bracket can be removed and pre-installed. Reserve the hardware for reattachment
of the horn.
3. Adjust to desired angle and tighten the adjustment knobs.
4. The loudspeaker can also stand on a tabletop or shelf – keep the yoke tight and directly behind
the loudspeaker.
5. Connect wires and adjust tap settings (see details here).
INSTALLATION
OVO5T Surface Mount Option

10 OVO3T / 5T Installation Guide
1. Adjust pan / tilt by loosening the knobs on both ends.
2. Position and tighten the adjustment knobs.
INSTALLATION CONTINUED
OVO5T Surface Mount Option
+/- 90° horizontal pan in
22.5° increments.
-15° Vertical Tilt (tilts
downward only)

11
OVO3T / 5T Installation Guide
1. Conrm the loudspeaker installation location.
2. Use wedge to mark the hole locations.
3. Align the wedge with U-bracket and attach to mounting surface (hardware not provided).
NOTE: The U-bracket can be removed and pre-installed. Reserve the hardware for reattachment
of the loudspeaker.
OVO5T Wedge Mount Option
Attach the U-bracket to the wedge mount for an additional 5” down-tilt.
INSTALLATION CONTINUED

12 OVO3T / 5T Installation Guide
4. Adjust to desired angle and tighten the knobs.
5. Connect wires and adjust tap settings (see details here).
INSTALLATION CONTINUED
OVO5T Wedge Mount Option

13
OVO3T / 5T Installation Guide
2. Lift the terminal levers and insert the wires into the correct terminal observing polarity.
3. Press each lever down to secure wires.
INSTALLATION WIRING
OVO3T Wiring
1. Peel back the tap switch access cover to view the terminals and tap setting knob.
NOTE: Pan or tilt the loudspeaker for easier access to the input panel.
Tap Switch Access Cover
Wire Routing
Terminal Lever Terminal Lever

14 OVO3T / 5T Installation Guide
4. Rotate the knob to select the appropriate tap setting.
5. Reinstall the cover and route the wires through the routing channels at the bottom of the cover.
Press all 4 corners down (and around the edge) to secure the cover.
1. Pull up on the raised wire routing area and peel back the tap switch access cover to view the
terminals and tap setting knob.
NOTE: Move the U-bracket to the side for easier access to the input panel.
INSTALLATION WIRING CONTINUED
OVO5T WIRING
OVO3T
Tap Switch Access Cover
Wire Routing

15
OVO3T / 5T Installation Guide
2. Lift the terminal levers to insert the wires into the correct terminal observing polarity.
3. Press lever down to secure wires.
4. Rotate knob to set the tap setting.
5. Reinstall the cover and route the wires through the routing channels at the bottom of the cover.
Press all 4 corners down (and around the edge) to secure the cover.
INSTALLATION WIRING CONTINUED
OVO5T
Terminal Lever
Terminal Lever
Tap Setting Knob

16 OVO3T / 5T Installation Guide
CAUTION: NEVER use abrasives, gasoline,
kerosene, acetone, methyl ethyl ketone (MEK),
paint thinner, harsh detergents or other
chemicals on the loudspeaker. These chemicals and
agents may permanently damage the nish. Some are
also toxic and highly ammable.
IMPORTANT: Take care not to bend or damage the
grille on removal or re-installation.
IMPORTANT: Blocking the grille holes with paint or
getting any paint on the drivers or internal parts will
affect loudspeaker performance and void the warranty.
IMPORTANT: For applications where certification is
required, ensure that relevant information on the rear
label is not painted over.
You will need:
•Removable masking tape or painter’s tape
•Machinist scribe tool or knife
•1.5 mm hex wrench
Useful Tip:
•Use a sharp knife to trim the masking material
close to the edges of the masked areas.
The OVO cabinets have a light paint coat over the
plastic material. They accept almost any type of
latex or enamel (oil based) paint. We recommend
application of two light coats.
IMPORTANT: Do not remove the grille.
Process
1. Remove brackets or mounts from the
loudspeaker to paint separately.
2. Use painter’s or other low-adhesive tape to
mask o the grille and area under the input
cover. NEVER use duct tape as it leaves an
adhesive residue that can be dicult to
remove and that may actually cause damage.
Painter’s or other low-adhesive tape is best.
3. Clean the loudspeaker cabinet with a lightly
dampened cloth. Do not use abrasives such
as sandpaper or steel wool.
4. Apply two or more thin coats of latex or
oil-based paint. Latex paint adheres better if
an oil-based primer is used rst. Spray paint
is best, but a brush may be used with light
coats.
5. Allow paint to fully dry and remove all of the
masking materials and reassemble.
PAINTING INSTRUCTIONS

[email protected] support.biamp.com
CONTACT US
Email: [email protected]
Web: support.biamp.com
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance