Bilt Backyard Discovery SWEETWATER User manual

Made in China
INS-2303010-A-SWEETWATER-ENG 09/19/22
Please visit www.backyarddiscovery.com
For the most up to date assembly manual, to register your set, or to order replacement parts
Para obtener instrucciones en español, visite www.backyarddiscovery.com
MANUFACTURED BY:
Backyard Discovery
3305 Airport Drive, Pittsburg, KS 66762
800-856-4445
WARNING
Adult Assembly Required.
The assembly manual must be retained since it contains important information
Not suitable for children under 24 months due to small parts.
FOR DOMESTIC USE ONLY. INTENDED FOR OUTDOOR USE.
Basepoint Business Centre: Rivermead Drive,Westlea, Swindon SN5 7EX Phone: [phone]
J.P. Coenstraat 7, The Bridge, The Hague, 2595 WP, Netherlands Phone: [phone]
SWEETWATER
PLAYHOUSE
Model # 2303010
CAN ICES-003 (B)/NMB-003(B)

General Information:
Your set has been designed and engineered for children only and for residential use only.
A maximum of 150 lbs. per child is recommended for play activities designed for individual use.
A maximum of 120 lbs. per child is recommended for play activities designed for multiple child use.
A maximum of 9 children is recommended for this swing set.
Owner's Manual Basic Setup Dimensions & Assembly Notes
SAFE PLAY AREA DIAGRAM
Selecting the correct location for your play product is important for your children’s
safety and the product’s longevity
The safe play area refers to a zone extending 6'-7" (2m) beyond the play product on all sides, including the space
above the play product.
6'-7"
[2 m]
3'-5 7/8" [1.1 m]
3'-10 5/8"
[1.2 m]
6'-7" [2 m]
16'-7 7/8" [5.1 m]
17'- 5/8"
[5.2 m]
3'-8 7/8"
[1.1 m]
4'-7 3/8" [1.4 m]
Ground Dimension
3'-5 7/8" (1.1 m) x 3'-10 5/8" x (1.2 m) x 4' 7-3/8" (1.4 m)
Safe Play Area
16'-7 7/8" (5.1 m) x 17'- 5/8" (5.2 m)
SAFE PLAY HEIGHT: 11'-2 3/8" [3.4 m]
MAXIMUM FALL HEIGHT: 4' 7-3/8" [1.4 m]
3'-10 5/8"
[1.2 m]
2

Owner's Manual Electronics Safety Warnings
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help
Caution: Changes or modifications not expressly approved by the party responsible for
3
CLASS B DIGITAL DEVICE STATEMENT

Owner's Manual
Wood Components (Not to Scale)
Parts Identification
GABLE BOARD - W4L17070
5/8”x4 3/8”x25 3/8” (16x112x643)
L1
(x4)
TRIANGLE SUNBURST - W4L17069
5/8”x5 1/4”x10 3/8” (16x134x265)
K1
(x2)
COUNTER TOP SUPPORT - W4L17067
1 3/8”x4 3/8”x5 7/8” (36x112x150)
D1
(x1)
REAR WINDOW SHELF - W4L17073
5/8”x2 3/8”x19 1/8” (16x60x485)
N2
(x1)
SUNBURST LEG - W4L17076
5/8”x2 3/8”x9 7/8” (16x60x250)
N5
(x2)
SUNBURST LEG - W4L17077
5/8”x2 3/8”x8 1/4” (16x60x210)
N6
(x4)
DOOR STOP - W4L17074
5/8”x2 3/8”x3 7/8” (16x60x100)
N3
(x1)
TIE STRAP - W4L17075
5/8”x2”x3 1/8” (16x50x80)
N4
(x8)
SIDE WINDOW SHELF - W4L17072
5/8”x2 3/8”x18 7/8” (16x60x479)
N1
(x2)
COUNTER TOP - W4L17071
5/8”x3 3/8”x18 1/2” (16x86x469)
M1
(x4)
COUNTER TOP SUPPORT - W4L17068
1”x2 3/8”x5 7/8” (24x60x150)
J1
(x2)
LOWER ROOF PANEL - W2A02982
1 3/8"x13"x44 7/8" (35x329x1140)
RP1
(x2)
UPPER ROOF PANEL - W2A02983
1 3/8"x12 3/4"x44 7/8" (35x324x1140)
RP2
(x2)
DP1
(x1)
DOOR ASSEMBLY - W2A03681
1 1/4"x13 1/8"x17 15/16" (32x334x456)
4

Owner's Manual
Wood Components (Not to Scale)
Parts Identification
WP3
(x1)
LEFT REAR CORNER PANEL - W2A03688
LENGTH 38 9/16" (980)
WP5
(x2)
LOWER CENTER WALL - W2A03694
1 1/2"x6 9/16"x20 7/8" (38x167x530) WP6
(x2)
UPPER CENTER WALL - W2A03695
1 1/2"x9 3/4"x20 7/8" (38x248x530)
WP8
(x1)
LOWER REAR CENTER WALL - W2A03697
1 1/2"x6 9/16"x21 1/8" (38x167x536)
WP7
(x1)
UPPER REAR CENTER WALL - W2A03696
1 1/2"x9 3/4"x21 1/8" (38x248x536)
WP9
(x2)
HEADER ASSEMBLY - W2A03698
3 3/8"x37 7/8"x38 7/8" (86x962x986)
WP1
(x1)
LEFT FRONT CORNER PANEL - W2A03682
LENGTH 38 9/16" (980) WP2
(x1)
RIGHT FRONT CORNER PANEL - W2A03685
LENGTH 38 9/16" (980)
WP4
(x1)
RIGHT REAR CORNER PANEL - W2A03691
LENGTH 38 9/16" (980)
5

Owner's Manual Parts Identification
Hardware Components
SCREW PFH
8x2 1/2"
(x6)
H100090
SCREW PWH
8x3/4
(x8)
H100070
SCREW PFH
8x1 1/8
(x30)
H100088
SCREW PFH
8 x 1/2
(x2)
H100124
SCREW PFH
8x1
(x38)
H100085
SCREW PFH
8x1 1/4
(x53)
H100087
WASHER LOCK EXT
6x15
(x4)
H100138
BOLT WH
1/4x1
(x4)
H100137
NUT BARREL WH
1/4x7/8
(x4)
H100140
SCREW PWH
8x7/16
(x2)
H100361
WASHER LOCK EXT
8x15
(x4)
H100139
TORX WRENCH
T-30
(x1)
H100114
TORX BIT
T-30
(x1)
H100147
SCREW SETTER
(x1)
H100764
SCREW PFH
8x1 1/2
(x22)
H100086
SCREW PWH
8x5/8
(x2)
H100128
SCREW PFH BLK
6x5/8
(x2)
H100624
SCREW PFH SD
8x1
(x2)
H100537
MAGNETIC DRIVER
(x1)
H101100
6

Owner's Manual
Accessory Components (Not to Scale)
Parts Identification
FRY PAN
(x1)
A6P00338
SPATULA
(x1)
A6P00339
LADLE
(x1)
A6P00340
POT/PAN LID
(x1)
A6P00337
BOIL POT
(x1)
A6P00336
STOVE KIT
(x1)
A6P00025
FAUCET KIT
(x1)
A6P00024
KNOB KIT
(x1)
A6P00020
FLOWER POT HOLDER - BLK
(x2)
A6P00387
PHONE KIT
(x1)
A100132
BE SURE TO WASH ALL PLASTIC TOYS BEFORE USE.
7

Owner's Manual
Accessory Components (Not to Scale)
Parts Identification
SURFACE MOUNT BASIN
(x1)
A6P00032
METAL TIE STRAP
(x1)
A4M00517
DOOR BELL PLATE
(x1)
A6P00290
DOOR BELL
(x1)
A100174
BYD ID TAG (MEDIUM) AGES 2 TO 10
(x1)
A4M00528
8

H100194 BOLT WH
5/16 x 2-1/2
(x2)
PRE-ASSEMBLY - SORTING PARTS
It is critical for ease of assembly that you take the time to sort and organize the wood and hardware.
WOOD PARTS:
•Organize wood parts by the three-digit, alpha-numeric number stamped on each board (ex. P01).
•If there are multiple boards with the same stamped number, stack those pieces together.
•Stamps can be found on the flat surface of the boards or on the end of the boards.
•Allow yourself plenty of room - the wood pieces can take up a significant amount of space.
•Resin coming from the knots in the wood pieces is natural and does not affect the quality of the wood,
but could cause yellowing around the knots.
NOTE: CARTONS ARE NOT ORGANIZED BY BOARD NUMBER.
HARDWARE PARTS:
• We recommend that you have a separate table to organize the hardware.
• Hardware bags are printed with a seven-digit, alpha-numeric part number.
• You can organize your hardware by part number or group by hardware type (i.e. bolts, nuts, etc.).
• During assembly you only need to reference the last four digits of the number.
STEP 1
9

PRE-ASSEMBLY - TOOLS REQUIRED
Cordless Drill or
Electric Drill
Drill Attachments:
Phillips Head
Open End Wrenches 1/2" & 9/16"
Phillips Screw Driver
1/8", 3/16", 3/8" & 7/16"
Drill Bits
3/8" Drive Ratchet, 1/2" &
9/16" STD Sockets 1/2" & 9/16" Deep
Sockets
Claw Hammer Rubber Mallet - Optional
Tape Measure
Square
Level 24"
STEP 2
10

PRE-ASSEMBLY - CHOOSE YOUR ASSEMBLY METHOD
There are several types of assembly instructions available to you.
1. Printed Assembly Manual included with your set
2. BILT APP - 3D interactive instructions
3. Combination of the Printed Manual and BILT APP (Note: Step numbers can differ between the two
methods)
STEP 3
11

NOTE:
POSITION WALL PANELS AS SHOWN
BELOW. VERIFY THE CORRECT PANEL
PLACEMENT BY CHECKING THE HOLE
LOCATIONS AS SHOWN BELOW.
WP (x1)
RIGHT FRONT CORNER PANEL
WP1 (x1)
LEFT FRONT CORNER PANEL
WP4 (x1)
RIGHT REAR CORNER PANEL
WP3 (x1)
LEFT REAR CORNER PANEL
STEP 1
NOTE HOLE LOCATIONS
NOTE HOLE LOCATIONS
NOTE HOLE LOCATIONS
NOTE HOLE LOCATIONS
WP1
(x1)
LEFT FRONT CORNER PANEL - W2A03682
LENGTH 38 9/16" (980)
WP2
(x1)
RIGHT FRONT CORNER PANEL - W2A03685
LENGTH 38 9/16" (980)
WP3
(x1)
LEFT REAR CORNER PANEL - W2A03688
LENGTH 38 9/16" (980)
WP4
(x1)
RIGHT REAR CORNER PANEL - W2A03691
LENGTH 38 9/16" (980)
12

NOTE:
STEP 2
085 (x10)
SCREW - 1"
WP6 (x1)
UPPER CENTER WALL
WP5 (x1)
LOWER CENTER WALL
SCREW PFH
8x1
(x10)
H100085
WP5
(x1)
LOWER CENTER WALL - W2A03694
1 1/2"x6 9/16"x20 7/8" (38x167x530) WP6
(x1)
UPPER CENTER WALL - W2A03695
1 1/2"x9 3/4"x20 7/8" (38x248x530)
ALIGN PANELS AS SHOWN BELOW THEN PRE-DRILL PILOT HOLES
USING AN 1/8" [3 mm] DRILL BIT, 1/2" [12 mm] DEEP FOR HARDWARE.
13

NOTE:
STEP 3
085 (x10)
SCREW - 1"
WP8 (x1)
LOWER REAR CENTER WALL
WP7 (x1)
UPPER REAR CENTER WALL
SCREW PFH
8x1
(x10)
H100085
WP7
(x1)
UPPER REAR CENTER WALL - W2A03696
1 1/2"x9 3/4"x21 1/8" (38x248x536)
WP8
(x1)
LOWER REAR CENTER WALL - W2A03697
1 1/2"x6 9/16"x21 1/8" (38x167x536)
ALIGN PANELS AS SHOWN BELOW THEN PRE-DRILL PILOT HOLES
USING AN 1/8" [3 mm] DRILL BIT, 1/2" [12 mm] DEEP FOR HARDWARE.
14

NOTE:
STEP 4
WP5 (x1)
LOWER CENTER WALL
WP6 (x1)
UPPER CENTER WALL
085 (x10)
SCREW - 1"
SCREW PFH
8x1
(x10)
H100085
WP5
(x1)
LOWER CENTER WALL - W2A03694
1 1/2"x6 9/16"x20 7/8" (38x167x530) WP6
(x1)
UPPER CENTER WALL - W2A03695
1 1/2"x9 3/4"x20 7/8" (38x248x530)
ALIGN PANELS AS SHOWN BELOW THEN PRE-DRILL PILOT HOLES
USING AN 1/8" [3 mm] DRILL BIT, 1/2" [12 mm] DEEP FOR HARDWARE.
15

STEP 5
088 (x6)
SCREW - 1 1/8"
SCREW PFH
8x1 1/8
(x6)
H100088
DP1 (x1)
DOOR ASSEMBLY
SIDE VIEW
NOTE PILOT HOLES
DP1
(x1)
DOOR ASSEMBLY - W2A03681
1 1/4"x13 1/8"x17 15/16" (32x334x456)
16

TIP:
ALIGN TIE STRAP WITH PILOT
HOLES AND ASSEMBLE AS
SHOWN.
STEP 6
070 (x8)
SCREW - 8x3/4"
517 (x1)
METAL TIE STRAP
SCREW PWH
8x3/4
(x8)
H100070
METAL TIE STRAP
(x1)
A4M00517
NOTE PILOT HOLES
17

NOTE:
REST HEADER ASSEMBLIES ON
THE WALL PANELS AND ASSEMBLY
AS SHOWN.
STEP 7
090 (x4)
SCREW - 1/ "
WP9 (x2)
HEADER ASSEMBLY
NOTE NOTCH
LOCATION.
SCREW PFH
8x2 1/2"
(x4)
H100090
WP9
(x2)
HEADER ASSEMBLY - W2A03698
3 3/8"x37 7/8"x38 7/8" (86x962x986)
18

STEP 8
087 (x32)
SCREW - 1-1/4"
N4 (x8)
TIE STRAP
TIE STRAP - W4L17075
5/8”x2”x3 1/8” (16x50x80)
N4
(x8)
SCREW PFH
8x1 1/4
(x32)
H100087
NOTE PILOT HOLES
19

STEP 9
137 (x4)
BOLT WH - 1"
138 (x4)
WASHER - 6x15
139 (x4)
WASHER - 8x15
140 (x4)
NUT BARREL - 7/8
L1 (x4)
GABLE BOARD
GABLE BOARD - W4L17070
5/8”x4 3/8”x25 3/8” (16x112x643)
L1
(x4) NUT BARREL WH
1/4x7/8
(x4)
H100140
BOLT WH
1/4x1
(x4)
H100137 WASHER LOCK EXT
6x15
(x4)
H100138 WASHER LOCK EXT
8x15
(x4)
H100139
20