airquee Snappy Operating instructions

Page 1of 6
Snappy
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
Site survey:
1. Carry out a survey of the area where the Snappy will be located, and check for any
overhead/underground cables. It’s important that this is carried out to avoid ground
anchors penetrating underground services, and the Snappy coming into contact with
overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to your
local power regulations.
3. Check wind speed: It is not allowed to use an inflatable by a higher wind force than
force 5 on the Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh breeze
when small trees in leaf begin to sway.

Page 2of 6
4X
4X
Included with your Snappy:
Extra equipment needed in addition what is supplied with your inflatable:
•Suitable 240v Power Supply to operate the fan
CAUTION! Precautions should be taken during handling and use
of the product to prevent electric shock. The blower requires a
Ground Fault Protected Circuit (GFCI). Please read the
manufacturer’s Instruction Manual before using the blower(s).
Extra equipment you could consider for your new inflatable:
•Ground sheet to protect the underside of your inflatable
•Sandbag covers to anchor your inflatable indoors
•Sack truck to move your inflatable safely
•RCD to attach to your extension lead
•Crash Mats
This inflatable can be set up and packed away by 4 persons who have
had proper manual handling training and use the correct equipment to
move the inflatable.
For information regarding dimensions, weight, zips, filler pipes and anchoring points
please refer to the visuals received for confirmation, and the email with the finished
pictures link.
Operating guidelines/Rules of play:
Before entering the game area, CLEAR INSTRUCTIONS SHALL BE GIVEN to players on their
conduct during playtime:
-No one with ANY PRE-EXISTING INJURIES OR HEALTH
CONCERNS may use the inflatable.
The inflatable
in its bag Fan Timer Box Anchor Pegs
LA0055 FP5005 AP0224
Anchor
Protectors Mattresses 6M Hose
AP2998 LA0029 AP0196
Land Operation
Manual
AP0222
Repair Kit
AP0217

Page 3of 6
2HP FAN:
FOR INFLATING THE
CHAMBER BENEATH THE
MOUTH, THUS MOVING IT
1.5HP FANS:
FOR INFLATING THE SLIDE
WEBBING CAM BUCKLE
STRAP FOR FIXING THE
INSTALLED FLEXIBLE HOSE
- Please be aware that this is not a bouncy castle and should
not be used for bouncing on.
- Do not use the product without the side scrim walls of the mouth.
- Before every play session, just after inflating the slide, please make sure all 4 cam
buckle straps (3 interior and 1 exterior) hold the installed hoses tightly.
- The moving jaw is to be used only for climbing. Do not allow players to jump down
from it.
For more information regarding operating guidelines and rules of play please see our main User
manual, section “20.9 Check-list for operators and attendants” (page 17) supplied with your unit,
and sent in an electronic format together with this file.
Set up:
- After unfolding the unit please connect the fans as follows:
The filler pipe that supplies the air for the movement of the mouth has an extra webbing cam buckle
strap. This is to hold the already installed flexible hose inside the filler pipe.
To access the chamber beneath the mouth, use the zip
highlighted in the picture beside.

Page 4of 6
INFLATION CHAMBER
BENEATH THE MOUTH
AIR OUTLET, THE END
OF THE 6M HOSE
AIR INLET, THE START
OF THE 6M HOSE
3M HOSE
THE HOSES INSIDE THE PRESSURE CHAMBER
BENEATH THE MOUTH ARE TIED WITH
WEBBING CAM BUCKLE STRAPS
THE TOP AND THE BOTTOM OF THE CHAMBER
ARE TIED TWICE WITH A COMBINATION OF A
BUNGEE CORD AND A WEBBING CAM BUCKLE.
ITS PURPOSE IS TO LIMIT THE ASCENSION OF
THE MOUTH TO THE DESIRED HEIGHT.
ACCESS ZIP
The 6m hose directs the airflow through the bed into the chamber beneath the mouth.
If you need to replace the 6M hose, you have to use the two zips highlighted with the color blue on
the figure found on the top of the page.

Page 5of 6
The 3M hose inflates the upper parts of the unit.
The lower part of the mouth is mounted with the
help of a Velcro strip.
Place all 4 supplied mattresses around
the unit as shown in the figure to the right.

Page 6of 6
Fan Timer Box:
The movement of the mouth is generated by the constant turning ON and OFF of the fan for the
chamber beneath the mouth. This is automated with the supplied Fan Timer Box.
IMPORTANT
IT IS IMPERATIVE THAT THE MOVING JAW WILL BE USED ONLY FOR CLIMBING.
PLAYERS SHOULD BE INSTRUCTED TO KEEP A CONTINUOUS MOVEMENT.
The electrical timer is designed to turn the fan ON and OFF at user defined intervals. It
must be connected between the main electrical socket and the fan that provides the
airflow for the movement of the jaw.
The timer is already set to an optimal jaw movement. We don’t recommend
changing these settings.
Airquee reserves the right to change the content of this manual without a prior notice to the customer.
The model of your product and the type and number of your inclusions may differ from the one presented in this
manual. All the pictures and drawings contained in this manual are for illustration purposes only.
ENJOY AND HAVE FUN!
Version 1.2 08/12/17
2HP FAN SOCKET
ELECTRICAL
SUPPLY SOCKET