Creative Playthings Manchester Premium Pack 8 User manual

MANCHESTER PREMIUM PACK 8
MANC9WPP8-100 Rev B (05-20)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
MANC9WPP8
M P P 
• Assemble the Manchester tower as shown in the instructions in Man-
chester Box 1 (63069-601).
• Manchester step 39. Do not install front wall slats.
• Assemble both Dormers (SM963-402). Install one Dormer on the
main tower roof before the swing beam, slide, or fun deck for better
ladder access.
• Tighten all connections on the Manchester then install the Fun Deck
using the instructions in 63070-301.
• Fun deck step 14. Instead of installing the corner posts use the cor-
ner roof posts from the fun deck roof (63070-404).
• Fun deck step 16. Do not install the end wall support included with
the fun deck. Use the end replacement included with the fun deck
spiral mount (63056-101). Installation is described in step 3 of the
spiral mount instructions.
• Fun deck step 22. Wait to install the narrow deck board on the side
where the spiral slide will mount. Set it in place but do not secure it.
• Fun deck step 23. Wait to install the wall slats on the longs sides of
the fun deck until after the spiral slide and roof are in place.
• Fun deck step 24. Do not install wall slats at the end of the fun deck.
The components of this gym can be combined with others to create different play sets. This is the best
order of assembly to create this specic set.
Read this sheet and all instructions included with the different parts before assembly.
See the Instructions and Owner's Manual included in carton 63069-601 for important safety information.
Dimensions of assembled package:
19' 0" wide x 26' 1" deep x 12' 10" tall
Cartons for this Play Set:
1 63069-601 Manchester Box 1 (Instr & Hdwre)
1 63069-602 Manchester Box 2
1 63069-603 Manchester Box 3
1 63069-604 Manchester Box 4
1 63069-605 Manchester Box 5
1 63069-606 Manchester Box 6 (Hardware)
1 63069-707 Manchester Box 7
1 8400-202 Spiral Slide (Hardware)
1 63056-101 Fun Deck Spiral Mount (Instr & Hdwre)
1 15140-400 14 Ft Swoosh Slide
1 50398-700 Swoosh Mount Pack (Instr & Hdwre)
1 63058-202 4 Position Swing Beam
1 63076-303 9ft Beam Legs (Instr & Hdwre)
1 50546-777 3 Swings, 1 Trapeze
1 63070-301 Manch. Fun Deck 1 (Instr & Hdwre)
1 63070-302 Manchester Fun Deck 2
1 63053-404 Manchester Fun Deck 3
1 63070-404 Manch Fun Deck Roof (Instr & Hdwre)
1 AP970-104 Bubble Panel (Instr & Hdwre)
2 SM963-402 Dormer (Instr & Hdwre)
2 SM964-402 Gable Fans (Instr & Hdwre)
1 AG943-400 Slide Handle (Instr & Hdwre)
1 AG942-400 Access Handles (Instr & Hdwre)

© Copyright 2018, Creative Playthings
MANCHESTER PREMIUM PACK 8
MANC9WPP8-100 Rev B (05-20) Page 2
• Install the spiral slide mount using the instructions included
in 63056-101.
• Spiral mount step 4. Do not install the cross brace.
• Spiral mount step 7. Before installing the side supports,
screw down the narrow deck board omitted in step 22 of
the fun deck assembly. If the deck board blocks a hole
drilled in spiral step 1, insert 5/16" weld nuts rst.
• Spiral mount step 9. Stop here before installing the slide
entrance. First install the roof to stabilize the fun deck.
• Install the Fun Deck Wood Roof (63070-404).
• Fun deck wood roof step 8. Install the fun deck wall slats
as shown. Leave the opening for the spiral slide and leave
off slats at the end of the fun deck for the bubble panel.
Leave a gap for the swoosh slide. The slide mount found
in the swoosh slide pack (50398-700) can be used to de-
termine the space needed.
• When the roof is complete resume installation of the spiral
slide at step 9.
• Install the swing beam using instructions from 63076-303
and step 46 in the Manchester manual. For proper t within
the play zone found in the Creative Playthings play zone
book, install the swing mount to the corner post near the
rung ladder as shown above.
• Install the remaining Dormer (SM963-402) on the fun deck
roof before installing the swoosh slide for better ladder ac-
cess.
• Install the Swoosh Slide (15140-400) in the position
shown.
• Install four wall slats across the opening on the front of the
main tower. All gaps must be smaller than 3-1/2" to prevent
possible head entrapment.
• Install the Gable Fans (SM964-402).
• Install the Bubble Panel (AP970-104) at the end of the fun
deck. There are special instructions for installing in this
position on page 3 of the bubble panel assembly guide.
Check the t before cutting to size.
• Install the Access Handles (AG942-400) on both sides of
the steps.
• Mount the Slide Handle (AG943-400) above the swoosh
slide.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.