BINO Hampton Changer User manual

IMPORTANT - RETAIN FOR FUTURE
REFERENCE. READ CAREFULLY.
WARNING : DO NOT LEAVE YOUR CHILD UNATTENDED -
YOUR CHILD'S SAFETY IS YOUR RESPONSABILITY
Hampton
Changer

THESE INSTRUCTIONS ARE IMPORTANT –
PLEASE READ CAREFULLY AND RETAIN FOR
FUTURE REFERENCE
We strongly suggest you spent a short time reading through this leaflet and then follow the simple step by
step guide to assembly.
WARNING : Do not leave your child unattended.
The correct use and maintenance of your changer will ensure it gives long and trouble free use. Remember
the safety of the child is your responsibility.
MATERIAL
Your changer is made in solid pine and MDF. Pine is a totally natural material therefor no two pieces are
ever identical in pattern or colour. As pine furniture gets older its colour may change due to being exposed
to light and air, so any new pieces may look a shade different to those you already have. Don’t be
concerned about this, as the colour difference will diminish over a small period of time.
Every piece has its unique appearance.
To keep the natural aspect, the surfaces were coated with a protective lacquer. The beauty of your furniture
can be maintained, cleaning it with a soft cloth. Occasionally a damp cloth, followed by a soft dry one,
may be used.
All furniture can be damaged by knocks and scrapes – if you dent the surface or break the seal of the
lacquer, apply some solid wax to exclude the atmospheric moisture.
ASSEMBLY
Before starting the assembly, please read through these instructions. Then carefully unpack your changer
and check that you have a complete set of parts against the list.
We recommend that you assemble your changer on a clean, flat surface, making sure there are no sharp
object present that may mark or damage the panels.
When gluing, use small amount of glue on the dowels and not in the dowel holes. Wipe away any excess
immediately with a clean damp cloth.
CAUTION
There are many small components used in the construction of this changer. These items should be kept
out of reach of young children whilst assembling the unit.

INSTRUCTIONS FOR SAFE USE
Thank you for choosing our product.
The changing surface is suitable for children up to 15kg in weight.
A changing pad must be used with this changer. Available separately
To ensure safe, trouble free use, please take a little time to read the important safety notes below and
following instructions.
SAFETY NOTES:
Keep children clear during assembly as pack contains small parts which may present a choking hazard.
All assembly fixings should always be correctly tightened and checked regularly.
Be aware of the risk of open fires and other such sources of strong heat, such as electric bar fires, gas fires,
etc in the vicinity of the changer
Do not use the changer if any part is broken, torn or missing.
Replacement parts should only be obtained from
Others may render the changer unsafe.
Once assembled, it is inadvisable to take the changer apart.
Apply all the brakes on the castor wheels when in use. (if applicable)
Designed and manufactured to BS EN 12221: 2008
CARE AND MAINTENANCE
Always store in a clean and dry place.
Do not use abrasives, bleach or strong detergents.
Scuff marks can be removed with mild soap and warm water.
Dry with soft towel.
Occasional use of furniture polish will maintain the finish of the unit.
Regularly check for loose parts and tighten when required.
Damaged or broken parts should be replaced.
WARNING: DO NOT leave your child unattended.
Global Procurement & Marketing Ltd
Grafton House
81 Chorley Old Road
Bolton
Lancashire
BL1 3AJ
Phone : [phone]

PARTS
1
2
3
5
5
4
5
56
6
6
8
9
10
11
7

HARDWARES
4cm
5cm
6cm
M6x60mm
A
Bolt
14X
GF
Screw
4X
3cm
2cm
1cm
0cm
H
Plastic
Washer
14X
Allen Key
1X
M4x35mm Dia.12x1mm
D
Cam-Bolt
4X
E
Cam-Lock
4X
4cm
5cm
3cm
2cm
1cm
0cm
M6x12mm
B
Nut
14X
8x30mm
Wooden Dowel
C
16X

ASSEMBLY
1.
X7
Bolt (M6x60mm) X7
A
Plastic Washer (Dia.12x1mm) X7
G
Nut (M6x12mm) X7
B
Wooden Dowel ( 8x30mm) X7
C
4
5
5
3
5
5
2
2
A
G
C
B

2.
3.
X7
6
1
Bolt (M6x60mm) X7
A
Plastic Washer (Dia.12x1mm) X7
G
Nut (M6x12mm) X7
B
Wooden Dowel ( 8x30mm) X7
C
A
G
C
B

4.
Cam-Bolt X4
D
Cam-Lock X4
E
Screw (M4x35mm) X4
F
CAM-PILLAR
NO GAP
Panel Panel
Shoulder
Tighten until shoulder is flush
with panel. Do not overtighen
or undertighten (see example
below)
CORRECT WRONG
WHEN FITTING CAMS
ENSURE STARTING POSITION IS CORRECT
BEFORE YOU INSERT CONNECTING CAM-PILLAR
TURN CLOCKWISE UNTILE SECURE
Pillar head needs to be in centre
Align with long point of cross
X4
F
5.
88
9
10
D
X4
X2
CAM-LOCK
EX4
11
7
Wooden Dowel ( 8x30mm) X2
C
E
C

6.
7.