Black & Decker Price Pfister Marielle 49M User manual

49M Series
Serie 49M
Série 49M
Lavatory Widespread Faucet
Grifo Extenso Para Baño
Robinet Sans Applique Pour Lavabo
06-16-04 EO6643Z
28692-0200
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
Copyright
©
2004, Price P ster, Inc.
©
2004, Price P ster, Inc.
©

Thank you for purchasing this Price P ster bathroom faucet. All Price P ster products are carefully engineered, and factory tested to provide
long trouble-free use under normal conditions. This bathroom faucet is easy to install using basic tools and our easy to follow illustrated
instructions. If you have any questions regarding your bathroom faucet installation call 1-800-Pfaucet (1-800-732-8238)
.
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding.
Price P ster recommends calling a professional if you are uncertain about
installing this product!
This product should be installed in accordance with all local and state plumbing and
building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are
usually found under the sink or near the water meter. If you are replacing an
existing faucet, remove the faucet from the sink and clean the sink surface
thoroughly.
3 TOOLS RECOMMENDED
• PTFE plumber's tape or thread sealant
• Plumber's putty
• Slotted screwdriver
• Phillips head screwdriver
• Pliers
• Adjustable wrench
• Flashlight
• Cloth
Your installation may require new supply lines and/or shut-off valves or other
additional tools.
This product comes with an installation tool used for securing the spout
assembly, and valve body assemblies.
INSTALLATION STEPS
4 SPOUT ATTACHMENT
Place Plastic Seal Ring (
4A
) against the bottom of Spout Body (
4B
).
Insert Spout Shank (
4C
) through the center hole of sink.
5 SPOUT INSTALLATION
From underneath sink, place Mounting Washer (
5A
) onto Spout Shank (
5B
)
and tighten with Mounting Nut (
5C
).
6 SECURING SPOUT
From underneath, tighten Mounting Nut (
6A
) by using Installation Tool (
6B
).
Before  nal tightening, be sure Spout (
6E
) is centered and facing forward. For
6E) is centered and facing forward. For 6E
better leverage, use a Screwdriver (
6C
), insert it through Hole (
6D
) and tighten
the Mounting Nut (
6A
) until Spout (
6E
) is  rmly secured to sink.
6E) is  rmly secured to sink.6E
2
3
4
5
6
2
ENGLISH
4A
4C
4B
5A
5B
5C
6A
6B
6C
6D
6A
6E
6E

7 VALVE BODY ATTACHMENT
Remove Clip (
7A
) from Valve Body (
7B
) and save. From above sink, insert
Valve Body (
7B
) through Mounting Holes (
7C
). The HOT valve, labeled with
Red Tag (
7D
), should be positioned to the left side of the spout.
8 VALVE BODY INSTALLATION
From underneath sink, place Mounting Washer (
8B
) onto Valve Shank (
8A
)
and tighten with Mounting Nut (
8C
).
9 SECURING VALVE BODY
From underneath, tighten Mounting Nut (
9A
) by using Installation Tool (
9B
).
For better leverage, use a Screwdriver (
9C
), insert it through Hole (
9D
) and
tighten the Mounting Nut (
9A
) until Valve (
9E
) is  rmly secured to sink.
9E) is  rmly secured to sink.9E
10 HOSE CONNECTION TO SPOUT BODY
From underneath sink, insert the Center Connector (
10A
) onto Spout
Shank (
10B
), push the Center Connector (
10A
) up until the top of Socket
(
10C
) reaches the Spout Shank Stop (
10D
). Be careful not to damage the
O-Ring Seals (
10E
). Thread Locknut (
10E). Thread Locknut (10E
10F
).
10F).10F
7
8
9
10
3
ENGLISH
7A
7B
7B
7B
7C
7C
7D
8A
8B
8C
9A
9D
9B
9C
9E
9E
9A
9A
9E
10C
10A
10F
10D
10B

12 SECURING HOSE CONNECTIONS
Replace Clips (
12A
) onto End Bodies (
12B
). Tighten Mounting Nut (
12C
) by
using Installation Tool (
12D
). For better leverage, use a Screwdriver (
12E
),
12E), 12E
insert it through Hole (
12F
) and tighten the Mounting Nut (
12F) and tighten the Mounting Nut (12F
12C
) until Center
Connector (
12G
) is  rmly secured to Spout Shank (
12H
).
13 VALVE ADAPTER ATTACHMENT
Thread Valve Adapters (
13A
) onto the Valve Stems (
13B
) and tighten so that
the Valve Adapters (
13A
) sit on the surface of the Valve Body Washers (
13C
).
14 HANDLE ATTACHMENT
Place Plastic Seal Rings (
14A
) against the bottom of Handle Hubs (
14B
).
Connect Handles (
14C
) onto Valve Adapters (
14D
).
11 HOSE CONNECTION TO VALVE BODY
Slide the End Connectors (
11A
) onto the Valve Bodies (
11B
). Push the End
Connectors (
11A
) all the way up until completely seated. Be careful not to
damage O-Rings (
11C
).
13
14
12
11
4
ENGLISH
11A
11A
11B
11B
12A
12A
12B
12B
12A
12A
12D
12F
12E
12C
12G
12H
12H
12G
12C
12B
13A
13A
13A
13A
13B
13B
13C
13C
14A
14A
14A
14A
14B
14B
14D
14D
11C
11C
14C
14C
12B

15 VALVE FUNCTION
Valve function – COLD valve: close-counterclockwise, open-clockwise;
HOT valve: close-clockwise, open-counterclockwise.
16 SECURING HANDLES
Be sure Valves and Levers are in the "OFF" position. Secure handles by
holding the Lever (
16B
) in place and tighten the Hubs (
16A
) by rotating them
in a clockwise direction. To remove handles, rotate Hubs (
16A
) in a
counterclockwise direction.
17 WATER SUPPLY CONNECTIONS
Connect water Supply Lines (
17A
) to Faucet Inlets (
17B
). (Supply lines and
 ttings are not included.)
18 POP-UP ROD CONNECTION
Insert Lift Rod (
18A
) into hole at top of Spout Head (
18B
). Gently, slide Lift
Rod (
18A
) down the Spout Head (
18B
) hole.
POP-UP DRAIN BODY INSTALLATION STEPS
19 POP-UP PREPARATION
Remove Flange (
19A
) and unscrew Nut (
19C
) from the Pop-Up Drain Body
(
19B
). Retain the Packing Ring (
19D
) inside the Ball Rod Opening (
19E
).
19E). 19E
Take off the Spring Clip (
19F
) from the Ball Rod (
19F) from the Ball Rod (19F
19G
). Place the Nut (
19C
)
on the Ball Rod (
19G
). Remove Locknut (
19H
), Friction Washer (
19J
),
Rubber Washer (
19K
) and Stopper (
19K) and Stopper (19K
19L
) from Flange (
19A
).
16
17
1815
19
5
ENGLISH
HOT
COLD
CLOSED
OPEN
CLOSED
OPEN
17A
17A
19A
19A
19D
19E
19C
19B
19F
19G
19G
19C
19K
19J
19H
19L
19A
19A
16B
16A
16A
18A
18A
18B
19B
17B

22 POP-UP ROD LINKAGE & ADJUSTMENT
Place one end of Spring Clip (
22C
) on end of Ball Rod (
22B
). Insert Ball
Rod (
22B
) across and through hole in Pop-Up Strap (
22D
). Secure other
end of Spring Clip (
22C
). Insert bottom of Lift Rod (
22A
) into hole at top of
Pop-Up Strap (
22D
). Tighten with Thumb Screw (
22E
). Adjust Lift Rod
(
22A
) function by adjusting location of Thumb Screw (
22E
) along the
Pop-Up Strap (
22D
) or by adjusting the hole in which Ball Rod (
22B
)
goes through the Pop-Up Strap (
22D
). Be sure to leave enough space
between Lift Rod Knob (
22F
) and Spout Head (
22F) and Spout Head (22F
22G
) when Lift Rod is down.
23 UNIT START UP
Turn on hot and cold water supplies, and check for leaks above and below
the sink
.
21 BALLROD ADJUSTMENT
Drop the Stopper (
21A
) into Drain Body (
21B
) from the top with the Off-Set
(
21C
) facing rear. From below, insert the Ball Rod (
21D
) into the Ball Rod
Opening (
21E
) through the Stopper Hole (
21E) through the Stopper Hole (21E
21F
) and secure with Nut (
21F) and secure with Nut (21F
21G
).
20 POP-UP INSTALLATION
Apply a small bead of putty underneath the Flange (
20A
) and place a ring
of putty around Drain Opening (
20B
) of sink. Use PTFE plumber’s tape to
all threaded  ttings according to manufacturer’s instructions. Insert Flange
(
20A
) into Drain Opening (
20B
). From underneath, insert Rubber Washer
(
20C
) and Friction Washer (
20D
) through the bottom of Flange (
20A
). Thread
Locknut (
20E
) until Rubber Washer (
20E) until Rubber Washer (20E
20C
) seats securely inside Drain Opening
(
20B
). Thread Drain Body (
20F
) to bottom of Flange (
20F) to bottom of Flange (20F
20A
). Hand tighten
and adjust the Drain Body so that the Ball Rod Opening (
20G
) faces the rear.
Wrench tighten Locknut (
20E
) and wipe excess putty.
20E) and wipe excess putty. 20E
22
23
20
21
6
ENGLISH
22A
22A
22C
22B
22D
22E
22F
22G
21A
21A
21B
21C
21E
21D
21F
21D
20A
20A
20C
20D
20E
20F
20G
21G
22B
22C
22E
22A
22A
22D
20B

1-800-PFAUCET (1-800-732-8238)
For Toll-Free Pfaucet information call
1-800-PFAUCET (1-800-732-8238)
or visit www.pricep ster.com
• Installation Support
• Care and Warranty Information
CAUTION: Maintenance
DISASSEMBLY
1.
Replacement parts may be available at the store where you
purchased your faucet.
2.
When replacement parts are not available, please write or
call Price P ster Consumer Service.
3.
Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all handles and decorative  nishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents, or acid may cause damage.
Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain porcelain or other similar
substances are not acceptable for public areas or commercial
use. Installation of said trim is at user’s risk!
24 FLUSHING & AERATOR CLEANING
To prevent damage to the internal parts of your faucet from debris that may
have collected in the water lines, please follow these steps:
1.
Turn on water supply valves.
2.
After connections have been made, remove Aerator (
24A
) and turn Handles
to the full “ON” position.
3.
Check for leaks, retighten where necessary, and let lines  ush for one minute
without moving faucet handles. This will remove debris from lines which
can damage internal parts of faucet and cause leaks.
4.
After  ushing, turn off handles and replace Aerator (
24A
).
To clean aerator, lift out Washer (
24B
) and Insert (
24C
) from Aerator Head
(
24A
). Rinse parts and replace.
25 VALVE CARTRIDGE MAINTENANCE
Turn off water supplies and relieve pressure before working on your faucet
(see step 2)
.
Remove Handles (
25A
)
(see step 16)
, Valve Adapter (
25B
)
(see step 13)
, unscrew Cartridge Assembly (
25C
) and inspect. Replace parts
as necessary.
26 HOSE CONNECTION MAINTENANCE
To detach Hose Assembly (
26A
), remove Clips (
26B
) from End Valve (
26C
)
and unscrew Locknut (
26D
) from Valve Stem (
26E
). Pull the Center Connector
26E). Pull the Center Connector 26E
(
26F
) and End Connectors (
26F) and End Connectors (26F
26G
) down until Hose Assembly (
26A
) is free.
Inspect parts and replace as necessary.
MAINTENANCE & CARE
26
24
25
7
ENGLISH
24A
24A
24B
24C
24A
24A
25A
25A
25B
25C
26C
26B
26B
26D
26C
26E
26F
26G
26G
26A
26A

19701 DaVinci
Lake Forest, CA 92610
Phone: 1-800-Pfaucet
www.pricep ster.com
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
EnglishEnglish
EspañolEspañol
FrançaisFrançais
*
*
A
Polished Chrome
Cromo Pulido
Chrome Poli
J
Brushed Nickel PVD
Niquel Cepillado PVD
Nickel Brosse PVD
Z
Oil Rubbed Bronze
Bronce Frotado Con Aceite
Bronze Huilé
931-009
910-025
COLD
FRÍO
FROID
950-025
950-200
931-600
931-940
971-019
972-019*
941-088*
910-024
HOT
CALIENTE
CHAUD
970-016
970-017
940-068*
941-087*
920-038*
949-004
900-024
COLD
FRÍO
FROID
900-023
HOT
CALIENTE
CHAUD
941-096
941-092*
970-016
970-017
950-025
950-200
931-600
49M Series
Serie 49M
Série 49M
Lavatory Widespread Faucet
Grifo Extenso Para Baño
Robinet Sans Applique Pour Lavabo