Black & Decker Price Pfister Avalon 49-CB Series User manual

49-CB Series
Serie 49-CB
Série 49-CB
Lavatory Widespread Faucet
Grifo Extenso Para Baño
Robinet Sans Applique Pour Lavabo
12-21-04 EO6784P
29484-0200
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
Copyright
©
2004, Price Pfi ster, Inc.
©
2004, Price Pfi ster, Inc.
©

2
3
4
5
6
Thank you for purchasing this Price Pfi ster bathroom faucet. All Price Pfi ster products are carefully engineered, and factory tested to provide
long trouble-free use under normal conditions. This bathroom faucet is easy to install using basic tools and our easy to follow illustrated in-
structions. If you have any questions regarding your bathroom faucet installation call 1-800-Pfaucet (1-800-732-8238)
.
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding.
Price Pfi ster recommends calling a professional if you are uncertain about
installing this product!
This product should be installed in accordance with all local and state plumbing and
building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are
usually found under the sink or near the water meter. If you are replacing an
existing faucet, remove the faucet from the sink and clean the sink surface
thoroughly.
3 TOOLS RECOMMENDED
• PTFE plumber's tape or thread sealant • Plumber's putty
• Slotted screwdriver • Phillips head screwdriver • Pliers
• Adjustable wrench • Flashlight • Cloth
Your installation may require new supply lines and/or shut-off valves or other
additional tools.
This product comes with an installation tool used for securing the spout, and valve body
assemblies, as well as a hex wrench for tightening a set screw into the handle.
INSTALLATION STEPS
4 SPOUT ATTACHMENT
Place the round Seal (
4A
) against the bottom of Spout Body (
4B
). Insert Spout
Shank (
4C
) through the center hole of sink.
5 SPOUT INSTALLATION
Insert Lift Rod (
5D
) into hole at the back of Spout (
5E
). From underneath sink,
5E). From underneath sink, 5E
place Mounting Washer (
5A
) onto Spout Shank (
5B
) and hand tighten with
Mounting Nut (
5C
). Align Lift Rod (
5D
) with slot in Mounting Washer (
5A
).
6 SECURING SPOUT
From underneath, tighten Mounting Nut (
6A
) by using Installation Tool (
6B
).
Before fi nal tightening, be sure Spout (
6E
) is centered and facing forward. For
6E) is centered and facing forward. For 6E
better leverage, use a Screwdriver (
6C
), insert it through Hole (
6D
) and tighten
the Mounting Nut (
6A
) until Spout (
6E
) is fi rmly secured to sink.
6E) is fi rmly secured to sink.6E
2
ENGLISH
4A
4C
4B
5A
5B
5C
6A
6B
6C
6D
6A
6E
6E
5D
5E

7
8
9
10
7 VALVE BODY ATTACHMENT
From above sink, insert Valve Body (
7A
) through Mounting Holes (
7B
). The
HOT valve, labeled with Red Tag (
7C
), should be positioned to the left side
of the spout.
8 VALVE BODY INSTALLATION
From underneath sink, place Mounting Washer (
8B
) onto Valve Shank (
8A
) and
tighten with Mounting Nut (
8C
).
9 SECURING VALVE BODY
From underneath, tighten Mounting Nut (
9A
) by using Installation Tool (
9B
). For
better leverage, use a Screwdriver (
9C
), insert it through Hole (
9D
) and tighten
the Mounting Nut (
9A
) until Valve (
9E
) is fi rmly secured to sink.
9E) is fi rmly secured to sink.9E
10 HOSE CONNECTION TO SPOUT BODY
From underneath sink, push the Center Connector (
10A
) onto receiving Tube
(
10B
), until unable to push any further. Pull down on the quick connect housing
(
10A
). If the housing and the Inner Collet (
10C
) separate slightly but do not pull
off the receiving Tube (
10B
), the connection is secure.
3
ENGLISH
7A
7A
7B
7B
7C
8A
8B
8C
9A
9D
9B
9C
9E
9E
9A
9A
9E
10A
10B
10B
10A
10B
10A
10A
10C

14
15
12
11
13
12 SECURING HOSE CONNECTIONS
Place Clips (
12A
) onto End Bodies (
12B
).
13 VALVE FLANGE ATTACHMENT
Place Plastic Ring (
13A
) and Flange (
13B
) over Valve Body (
13C
) covering
the Valve Body Washers (
13D
). Secure by screwing the Plastic Nut (
13E
) onto
13E) onto 13E
the Valve Body (
13C
).
14 VALVE FUNCTION
Valve function—COLD valve: close-counterclockwise, open-clockwise.
HOT valve: close-clockwise, open-counterclockwise.
15 HANDLE ATTACHMENT
With valves in "CLOSE" position, place
Handle Hub (
15A
) onto Valve Stem (
15B
)
and secure with Fastener (
15C
). Connect Lever (
15D
) onto Handle Hub (
15A
)
and secure by tightening Set Screw (
15E
) with Hex Wrench (
15E) with Hex Wrench (15E
15F
).
15F).15F
11 HOSE CONNECTION TO VALVE BODY
Slide the End Connectors (
11A
) onto the Valve Bodies (
11B
). Push the End
Connectors (
11A
) all the way up until completely seated. Be careful not to
damage O-Rings (
11C
).
4
ENGLISH
HOT
COLD
CLOSED
OPEN
CLOSED
OPEN
11A
11A
11B
11B
12A
12A
12B
12B
12A
12A
13E
13E
13D
13B
13B
11C
11C
15A
15A
13A
13A
13A
13A
13C
15B
15C
15D
15E
15F

17
18
19
16
16 WATER SUPPLY CONNECTIONS
Connect water Supply Lines (
16A
) to Faucet Inlets (
16B
).
(Supply lines and
fi ttings are not included).
Please follow manufacturer’s instructions when
installing supply lines.
17 POP-UP PREPARATION
Remove Flange (
17A
) and unscrew Nut (
17C
) from the Pop-Up Drain Body
(
17B
). Retain the Packing Ring (
17D
) inside the Ball Rod Opening (
17E
). Take
17E). Take 17E
off the Spring Clip (
17F
) from the Ball Rod (
17F) from the Ball Rod (17F
17G
). Place the Nut (
17C
) on the
Ball Rod (
17G
). Remove Locknut (
17H
), Friction Washer (
17J
), Rubber Washer
17J), Rubber Washer 17J
(
17K
) and Stopper (
17K) and Stopper (17K
17L
) from Flange (
17A
).
18 POP-UP INSTALLATION
Apply a small bead of putty underneath the Flange (
18A
) and place a ring of
putty around Drain Opening (
18B
) of sink. Use PTFE plumber’s tape to all
threaded fi ttings according to manufacturer’s instructions. Insert Flange (
18A
)
into Drain Opening (
18B
). From underneath, insert Rubber Washer (
18C
) and
Friction Washer (
18D
) through the bottom of Flange (
18A
). Thread Locknut
(
18E
) until Rubber Washer (
18E) until Rubber Washer (18E
18C
) seats securely inside Drain Opening (
18B
).
Thread Drain Body (
18F
) to bottom of Flange (
18F) to bottom of Flange (18F
18A
). Hand tighten and adjust the
Drain Body so that the Ball Rod Opening (
18G
) faces the rear. Wrench tighten
Locknut (
18E
) and wipe excess putty.
18E) and wipe excess putty. 18E
19 BALL ROD ADJUSTMENT
Drop the Stopper (
19A
) into Drain Body (
19B
) from the top with the Off-Set (
19C
)
facing rear. From below, insert the Ball Rod (
19D
) into the Ball Rod Opening
(
19E
) through the Stopper Hole (
19E) through the Stopper Hole (19E
19F
) and secure with Nut (
19F) and secure with Nut (19F
19G
).
POP-UP DRAIN BODY INSTALLATION STEPS
5
ENGLISH
16B
16A
16A
18A
18A
17C
19D
17D
17E
17A
17A
17G
17K
17J
17H
17B
17L
18B
18C
18D
18E
18F
18G
19G
19E
19B
19F
19D
19A
19A
19C
17C
17G
17F

23
22
20
21
20 POP-UP ROD LINKAGE & ADJUSTMENT
Place one end of Spring Clip (
20C
) on end of Ball Rod (
20B
). Insert Ball Rod
(
20B
) across and through hole in Pop-Up Strap (
20D
). Secure other end of
Spring Clip (
20C
). Insert bottom of Lift Rod (
20A
) into hole at top of Pop-Up
Strap (
20D
). Tighten with Thumb Screw (
20E
).
20E). 20E
Adjust Lift Rod (
20A
) height by
using the Thumb Screw (
20E
) on the Strap (
20E) on the Strap (20E
20D
)
or by adjusting the hole in
which Ball Rod (
20B
) goes through the Pop-Up Strap (
20D
). Be sure to leave
enough space between Lift Rod Knob (
20F
) and Spout Head (
20F) and Spout Head (20F
20G
) when Lift
Rod is down.
21 UNIT START UP
Turn on hot and cold water supplies, and check for leaks above and below
the sink
.
2
2
FLUSHING & AERATOR CLEANING
After installation is complete, remove Aerator Housing (
22A
). Turn Valves
(
22B
) on and allow both hot and cold water to run for at least one minute each.
While water is running, check for leaks. To clean the aerator, disassemble Aerator
Housing (
22A
) by separating the Aerator Shell (
22C
), Basket (
22D
), and Washer
(
22E
). Once parts have been cleaned, reassemble by reversing steps.
22E). Once parts have been cleaned, reassemble by reversing steps.22E
23 VALVE CARTRIDGE MAINTENANCE
Turn off water supplies and relieve pressure before working on your faucet (see
step 2). Remove Handles (see step 15), Valve Flange (
23B
) and Plastic Nut
(
23C
) (see step 13), unscrew Cartridge Assembly (
23A
) and inspect. Replace
parts as necessary.
MAINTENANCE & CARE
6
ENGLISH
23C
22A
22A
20F
20G
20A
20A
20E
20C
20D
20B
20A
20A
20E
20D
20B
20C
22B
22E
22D
22C
23B
23A
23A

24
1-800-PFAUCET (1-800-732-8238)
For Toll-Free Pfaucet information call
1-800-PFAUCET (1-800-732-8238)
or visit www.pricepfi ster.com
• Installation Support
• Care and Warranty Information
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store where you
purchased your faucet.
2. When replacement parts are not available, please write or
call Price Pfi ster Consumer Service.
3. Always turn off water and relieve pressure before
working on your faucet.
24 HOSE CONNECTION MAINTENANCE
To detach Hose Assembly (
24A
), remove Clips (
24B
) from End Valve (
24C
)
and pull the End Connectors (
24D
) from End Valves (
24C
). Remove Center
Connector (
24E
) by pushing up on Quick Connect Housing (
24E) by pushing up on Quick Connect Housing (24E
24F
). Holding gray
24F). Holding gray 24F
plastic Collet (
24G
) in place, pull down on Quick Connect Housing (
24F
) until
24F) until 24F
Tube (
24H
) is free.
NOTE: Trim Care
Cleaning Instructions:
For all handles and decorative fi nishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents, or acid may cause damage.
Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain porcelain or other similar
substances are not acceptable for public areas or commercial
use. Installation of said trim is at user’s risk!
7
ENGLISH
24B
24C
24C
24B
24D
24E
24D
24G
24F
24H
24F
24A
24A

19701 DaVinci
Lake Forest, CA 92610
Phone: 1-800-Pfaucet
www.pricepfi ster.com
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
49-CB Series
Serie 49-CB
Série 49-CB
EnglishEnglish
EspañolEspañol
FrançaisFrançais
*
*
La Letra Indica el Terminado
La Letra Indica el Terminado
La Lettre Designe La FiniLa Lettre Designe La Fini
A
Polished Chrome
Cromo Pulido
Chrome Poli
J
Brushed Nickel PVD
Niquel Cepillado PVD
Nickel Brosse PVD
910-025
COLD
FRÍA
FROID
910-024
HOT
CALIENTE
CHAUD
900-024
COLD
FRÍA
FROID
900-023
HOT
CALIENTE
CHAUD
950-200
950-025
931-600
960-010*
940-106*
960-051*
950-330
931-940
941-134*
931-009
941-200*
971-005
972-019*
920-501*
931-017
971-024
971-702