BlueSpot 19600 User manual

FLAP WHEELS
User Manual
19600 / 19602 / 19604 / 19606 / 19608 / 19610 / 19612 / 19614 /
19616 / 19618 / 19620 / 19622 / 19624 / 19626 / 19628 / 19630

01
Thank you for purchasing a BlueSpot product, you can find further information
on our range at www.BlueSpot.uk.com. Please ensure that you are using the
product correctly and that all guidance and cautions are followed in accordance
with the instructions. Please retain these instructions for future reference.
General Information
Please make sure that you read these instructions carefully in order to avoid injury when
using the flap wheels. Follow all health and safety rules and regulations. If in doubt and
available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure the flap wheels have been checked for any damage before use. Any
damage found needs to be repaired or replaced before use to prevent damage to
property or personal injury.
• ALWAYS ensure that operators are trained in the use of flap wheels and understand and
follow the safety requirements before operation.
• ALWAYS make sure the wheels have been mounted correctly and securely. Always
ensure the instructions have been followed carefully before use.
• ALWAYS handle flap wheels with care to avoid accidental damage.
• ALWAYS check maximum operating speed of the flap wheel and drill.
• ALWAYS wear approved ear and eye protection when using flap wheels.
• ALWAYS wear approved hand protection when using flap wheels.
• ALWAYS wear approved dust respirators when using flap wheels.
• Maintain tool in good and clean condition for best and safest performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Keep children and unauthorised persons away from the work area.
• BE AWARE of where your body is positioned when using the flap wheel. The body
should not be positioned in line with the flap disc.
• DO NOT exceed the maximum operating speed of the flap wheel.
• DO NOT exceed the maximum operating speed of the drill.
• DO NOT force the flap wheels onto a machine which does not match the bore size.
Safe use
• DO NOT alter the size of the flap wheel bore.
• NEVER use the flap wheels to perform a task that they were not designed for.This can
cause damage to property or cause personal injury.
• NEVER use the flap wheels near flammable materials or gases.
• If any of the flap wheels are damaged do not use.

Stock Code
19600
19602
19604
19606
Grit
40 grit
60 grit
80 grit
120 grit
Diameter
25mm
25mm
25mm
25mm
Shank
6mm
6mm
6mm
6mm
Maximum Safe Speed
25000rpm
25000rpm
25000rpm
25000rpm
Box Quantity
10
10
10
10
Stock Code
19608
19610
19612
19614
Grit
40 grit
60 grit
80 grit
120 grit
Diameter
50mm
50mm
50mm
50mm
Shank
6mm
6mm
6mm
6mm
Maximum Safe Speed
13000rpm
13000rpm
13000rpm
13000rpm
Box Quantity
10
10
10
10
Stock Code
19616
19618
19620
19622
Grit
40 grit
60 grit
80 grit
120 grit
Diameter
60mm
60mm
60mm
60mm
Shank
6mm
6mm
6mm
6mm
Maximum Safe Speed
11000rpm
11000rpm
11000rpm
11000rpm
Box Quantity
10
10
10
10
Please make sure that you read these instructions carefully in order to avoid injury when
using the flap wheels. Follow all health and safety rules and regulations. If in doubt and
available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure the flap wheels have been checked for any damage before use. Any
damage found needs to be repaired or replaced before use to prevent damage to
property or personal injury.
• ALWAYS ensure that operators are trained in the use of flap wheels and understand and
follow the safety requirements before operation.
• ALWAYS make sure the wheels have been mounted correctly and securely. Always
ensure the instructions have been followed carefully before use.
• ALWAYS handle flap wheels with care to avoid accidental damage.
• ALWAYS check maximum operating speed of the flap wheel and drill.
• ALWAYS wear approved ear and eye protection when using flap wheels.
• ALWAYS wear approved hand protection when using flap wheels.
• ALWAYS wear approved dust respirators when using flap wheels.
• Maintain tool in good and clean condition for best and safest performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Keep children and unauthorised persons away from the work area.
• BE AWARE of where your body is positioned when using the flap wheel. The body
should not be positioned in line with the flap disc.
• DO NOT exceed the maximum operating speed of the flap wheel.
• DO NOT exceed the maximum operating speed of the drill.
• DO NOT force the flap wheels onto a machine which does not match the bore size.
02
Safe use (continued)
• DO NOT alter the size of the flap wheel bore.
• NEVER use the flap wheels to perform a task that they were not designed for.This can
cause damage to property or cause personal injury.
• NEVER use the flap wheels near flammable materials or gases.
• If any of the flap wheels are damaged do not use.
The BlueSpot Flap Wheels are designed to be used with power drills, pillar drills and air
drills. Ideal for grinding, polishing and removing rust.
Recommended operating speed - 15-20m/s
Introduction
Specification
25mm Flap Wheels
50mm Flap Wheels
60mm Flap Wheels

Stock Code
19624
19626
19628
19630
Grit
40 grit
60 grit
80 grit
120 grit
Diameter
80mm
80mm
80mm
80mm
Shank
6mm
6mm
6mm
6mm
Maximum Safe Speed
8000rpm
8000rpm
8000rpm
8000rpm
Box Quantity
10
10
10
10
03
Specification (continued)
80mm Flap Wheels
Advantages
Operation
ALWAYS ensure that operators are trained in the use of flap wheels and understand and
follow the safety requirements before operation.
1. Choose a suitable flap wheel.
Always ensure that you have chosen the appropriate flap wheel for the task. Refer to the
specification above when choosing the correct flap wheel for the task.
2. Mounting the flap wheel.
Always ensure you follow the instructions of your chosen electric drill when mounting
any flap disc.
3. Securing the work object.
Always ensure that the work object you are working on is firmly secured to minimise
movement during the grinding process.
4. Grinding, polishing and removing rust.
Always ensure you hold the drill with a firm grip when in use. Carefully move the flap
wheel across the bulk or body of your workpiece.
5. Finishing.
Always ensure you slowly and carefully lift the drill from the surface of the work when
finishing any task.
• Removes the surface layer of various metals evenly by lightly grinding and deburring.
• To be used with power drills, pillar drills and air drills.
• The flexible design of the flap wheel make them ideal for smoothing curved surfaces and
reaching edges and corners effectively.
• Sharp abrasive grit is exposed at all times.

04
ContactDistance to Spot SizeDisposal
Clean the flap discs with a dry cloth if needed. Make sure the flap discs are not in use when
cleaning.
Cleaning & Maintenance
ContactDistance to Spot SizeDisposal
ALWAYS ensure the flap discs are stored out of reach of children.
Store the tool in a secure, dry place.
Storage
ContactDistance to Spot SizeDisposal
Cleaning & Maintenance
Notes
ContactDistance to Spot SizeDisposal
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycling centre and disposed of in a manner which is
compatible with the environment. When the product becomes completely unserviceable and
requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Environmental Protection
Always check and adhere to national regulations when disposing of any tools that are no longer
functional and cannot be repaired.
• Contact your local waste disposal authority for information on how to correctly
dispose of tools.
Disposal
Contact
Find out more about BlueSpot® products at www.BlueSpot.uk.com
Tel: [phone]
Email: [email protected]
Orme Business Centre, Greenacres Road,
Oldham, OL4 3NS

ContactDistance to Spot SizeDisposal
Notes
05