BOERPLAY Detached Slide with handles H1.5 User manual

Detached Slide with handles H1.5
BBPE020.3KR
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3KR
C
Vrijstaande glijbaan 1,45 m
Boer Basic play
18-12-2023
Hoofdafmetingen Main dimensions
0,00 m
1,45 m
2,16 m
0,00 m 2,20 m 2,36 m 3,12 m
0,00 m
0,05 m
0,85 m
0,90 m
66°
Openingen altijd > 25 mm
Openings always > 25 mm
<0,35 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3KR
C
Vrijstaande glijbaan 1,45 m
Boer Basic play
18-12-2023
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
6,32 m 5,82 m
R1,50m
3,89 m
0,50 m1,14 m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3KR
Vrijstaande glijbaan 1,45 m
Boer Basic play
18-12-2023
Bodemplan Groundplan
C
Grondmarkering
Ground level marker
0,61 m
0,71 m
4,71 m
0,80 m
1,55 m 1,54 m
0,25 m
0,75 m
0,36 m
0,10 m
1,61 m
2,83 m
0,40 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3KR
Vrijstaande glijbaan 1,45 m
Boer Basic play
18-12-2023
Modules Modules
C
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
Basic PlayGlijbaan 145 cm 146
BBP
MOD
11
Boer Basic playLadder 1,45m glijbaan
DK
569
BBP
MOD12
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 1 onder de uiste hoek en met de uiste hoogte
3 - Plaats 2, verbind deze aan 1
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - De hoek van de trap
3 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1 with the right angle and right height
3 - Place 2, attach it to 1
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - The angle of inclination of the ladder
3 - Check the dimensions of the safety area with regard to the play equipment
2
1
Typeplaatje
Identification plate
B

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3KR
Vrijstaande glijbaan 1,45 m
Boer Basic play
18-12-2023
Afmetingen Dimensions
C
0,00 m
0,31 m
0,59 m
0,87 m
1,15 m
1,46 m
2,16 m
0,00 m
0,54 m
1,45 m
1,84 m
2,16 m

LOGBOOK
Type indication Basic Play
Article number BBPE020.3KR
Product Name Detached Slide with handles H1.5
Maximum fall height 1,5 m
Construction year 2023
Certificate 137792
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
BORG RVS M10DOPMOER 020010011BSR61
M10 x 40 - RVS A2-70Slotbout 040010026BSR62
M10 x 30 x 2,5CARROSSERIERING 030010035BSR63
145 m
Glijbaan
A
320664
VRB
SME1
4
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 146 R
Glijbaan 145 m
Basi Play
20-2-2017
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
2
3
1
4
Grondmarkering
Ground level marker
0,60 m
Let op: toestel bij voorkeur niet met
de glijbaan op het zuiden plaatsen.
Attention: it is advisable not to oriënt
pla ground equipment with the slide
facing south
1,45 m
0,29 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 569 K
Ladder 1,45m glijbaan
Boer Basic play
18-12-2023
Samenstelling module Assembly module
D
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
5 x 70 - R S A2-70
Schroef Assy
070005002BSR8
1
5 x 50 - R S A2-70
Schroef Assy
050005002BSR
44
2
M10 - Z 8.8
Borgdopmoer
020010011BS43
M10x80
Slotbout
080010026BS44
M10 ZSLUITRING 002010030BS55
ZWART
ROZETRING M5 000006RORKST426
Paalkap 100x100
C
xxx
100
KAP
OME2
7
100 x 100
oetplaat
CZP903RBOME28
Basic Play
Startplatform glijbaan R S
061092BBPOPE19
Klemblok
090119BBPOPE210
Boer Basic playHandgreep glijbaan
B
061136
BBP
OPE2
11
Basic PlayStaander 3,0m
136
BBP
ORE212
Boer Basics
Railing 003
BBP
SME
1
13
Basic PlayHandgreep
A
005
BBP
SME2
14
Basic PlayTraptrede
A
011
BBP
SME
4
15
2
7
49
3
5
10
2
6
14
66°
331
Grondmarkering
Ground level marker
13
11
1
6
12
433
0
2
700
1042
1346
1650
1954
2231
3000
3017
2
8
15
Powered by TCPDF (www.tcpdf.org)