Creative Playthings 63080-101 User manual

Parts:
A 1 35200-102 SwingMount4x4x35-1/2"
B 1 35242-102 LegBrace4x4x55-1/2"
C 1 35303-102 CenterBlock2-3/4x3-1/4x8"
D 1 35304-102 SideBlockOne4x4x13-1/4"
E 1 35305-102 SideBlockTwo4x4x13-1/4"
F 1 40594-102 3PositionBeamAssembly
G 2 40595-102 LegAssembly
H 1 14162-400 8"L-Brace,Green,LargeHoles
Classic Pine Swing Beam Model:
63080-101
CPSCrecommendsasafeplay
zone in front of and behind the
swings that is twice the height of
theswingpivot,andclearspaceex-
tending6'aroundtheplaystructure.
Please review the instructions and
manual provided with the gym for
safety information and instructions
onpropergroundcover.
I 1 14233-400 BeamRetainer,Green
J 2 14234-400 HDAngleBracket,Green
K 3 36515-102 GroundStake2x2x18"
L 1 50229-700 Ny-GlideSwingHangers
M 1 14209-100 CreativeNameplate
AA934-204 2Swings,1Trapeze
All hardware on this set is specially coated for corrosion resistance. If non-Creative Playthings
hardware is used, it must be galvanized or stainless steel.

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 2
Fasteners:
8 12002-206 5/16"FlatWasher
4 17036-1002 5/16x2-1/2"LagScrew
4 17036-2202 5/16x5-1/2"LagScrew
6 17020-113 Screw#10x2-1/2"
4 12002-207 FlatWasher3/8
4 12017-207 LockWasher3/8
4 17001-103 WeldNut3/8"
1 17003-1213 HexBolt3/8x3"
2 17003-1413 HexBolt3/8x3-1/2"
1 17003-2613 HexBolt3/8x6-1/2"
4 12002-209 1/2"FlatWasher
3 17123-3418 HexBolt1/2x10"
3 12052-109 1/2"NylockNut
Hex Bolt 1/2 x 10" (Truncated to t on page)
Hex Bolt 3/8 x 6-1/2"
Hex Bolt 3/8 x 3-1/2" Screw #10 x 2-1/2"
Hex Bolt 3/8 x 3" Lag Screw 5/16 x 2-1/2"
Lag Screw 5/16 x 5-1/2"
Flat Washer 5/16"Flat Washer 3/8"Lock Washer 3/8" Weld Nut 3/8"
Flat Washer 1/2"Lock Nut 1/2"
50551-700 Classic Pine Swing Beam Fasteners

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A.
Page 3
STEP TWO - Swing Hangers
Place the Beam (F) on the ground with the holes for the
SwingHangersfaceup.PlacetheBeamapproximately90"
fromthesideofthegymwiththeSwingMount.
CarefullyfollowtheinstructionincludedwiththeSwingHang-
erstoinstalltheSwingHangersinthepositionsshown.
STEP THREE - Block Assembly
STEP ONE - Swing Mount
ForastandardinstallationonaClaytonorNorthbridgegym,
mountingholesarepre-drilled.
Fasten the Swing Mount to the Swing Wall Support and
Swing Platform Side using two 5/16 x 4-1/2" Hex BoltAs-
sembliesasshownatright.
* Note: a Hex Bolt Assembly consists of one Hex Bolt passing
through one Lock Washer and one Flat Washer, threaded into
one Weld Nut.
C
E
D
FastenSideBlockOne(D),CenterBlock(C),andSideBlock
Two(E)totheBeamatthegymendasshown.Useone1/2
x10"HexBolts,two1/2"FlatWashers,andoneNylonLock
Nutforeachconnection.
SwingMount
Forinstallationinanalternativepositionmakesuretherewillbe14'ofclearareainfrontandinbackoftheswings.Holdthe
SwingMountagainstthecenterofthesideofthegymchosen.Markthepositionoftheholes.Checkforinterferinghard-
ware.Drill3/8"diameterholesthroughthesupportsatthemarks.Installasinstructedabove.
90"
F
L
Thefastenersare
foundinthegym
hardwarepack

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 4
STEP FIVE - Secure Brackets
STEP FOUR - Legs and Brackets
Fasten two HDAngle Brackets (J) and two LegAs-
semblies(G)totheCenterBlockasshown.
Useone1/2x 10"HexBoltand one 1/2"
LockNuttosecurethem.DonotuseFlat
Washers.
Do not fully tighten the connection
at this time so the parts will pivot
on the bolt when erecting the
SwingBeam.
G
Adjustthelegssotheyproject90°outfromtheBeam.
AligntheholesintheHDAngleBracketswiththepre-drilled
holesintheBeam.SecuretheBracketstotheBeamusing
four5/16x2-1/2"LagScrewsandfour5/16"FlatWashers.
J
J

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A.
Page 5
STEP SIX - Flip Beam
Withthe help of others, ip the Beam end-over-
end and lean the Beam against the side of the
gymnexttotheSwingMount.
IfthereisaWallSlatonthegymadjacenttothe
Swing Mount, remove it to avoid conict during
the following steps. Once the Beam is in place,
replacetheWallSlat.
STEP SEVEN - Beam to Swing Mount
SecureoneholeoftheL-Brace(H)tothesecondholeontheBeamAs-
semblyusingone3/8x3"HexBoltAssemblyasshown.Aligntheholein
thecorneroftheL-BracewiththeendholeintheBeamAssembly.
Usea3/8x6-1/2"HexBoltAssemblytofastentheBeamRetainer(I),
BeamAssembly,andL-Bracetotheholesecondfromthetoponthe
SwingMount.DonotfullytightenastheBeamwillpivotduringassembly.
STEP EIGHT - Raise Beam
Withthehelpofothers,raisetheBeamandswingtheLegs
into place to support it. Set the ends of the legs into the
groundanduseacarpenter'sleveltomakesuretheBeam
islevel.
NOTE: If the ground falls away on the Beam side of the
gym, the Beam can be shifted to a lower hole on the
Swing Mount.

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 6
STEP NINE - Leg Brace
STEP TEN - Secure Top of Leg
STEP ELEVEN - Secure Beam Retainer
WithhelperssteadyingtheLegs,holdtheLegBrace(B)in
thepositionshown.Makesureitislevelandtheendsdonot
overhang.
MarkthepositionoftheholesintheLegBraceontotheLegs.
Drill1/4"diameterpilotholes2"deepatthemarks.
Securethe Leg Braceto the Legsusing two 5/16x 5-1/2"
LagScrewsandtwoFlatWashers.
MakesurethefrontfaceoftheBeamisplumb.Findthere-
mainingholesinSideBlockOneandSideBlockTwo.Drill
1/4"diameterpilotholesthroughtheholesintheBlocksand
2"deepintotheLegs.
SecuretheBlockstotheLegsusingtwo5/16x5-1/2"Lag
ScrewsandtwoFlatWashers.
Tighten the three 1/2 x 10" Hex Bolts that secure the
Blocks, Legs and Angle Braces. Make sure the end of
the Bolts protrude through the Lock Nuts approximately
two threads.
SecuretheBeamRetainerandL-BracetotheSwingMount
using3/8x3-1/2"HexBoltAssemblies.
TightenallthreeBoltssecuringtheBeamtotheSwingMount.

Classic Pine Swing Beam Instructions - 19928-100A (01/16)
Copyright 2016, Creative Playthings - Printed in U.S.A.
Page 7
STEP TWELVE - Ground Stakes
STEP THIRTEEN - Nameplate
STEP FOURTEEN - Hang Swings
Driveeach Stake into the ground next to the SwingBeam
Legs, as shown. Secure the Stakes directly into the base
oftheLegAssembliesusingtwo#10x2-1/2"Screwseach.
ThetopoftheStakesmustnotextendbeyondtheproleof
theleg.
Note:Do NOTuseconcrete to setGround Stakes. Simply
drive them in to the ground. In hard or rocky soil, drive a
metalspikeorrodasapilotholeforthewoodenstakes.
Federal law requires the name of the manufacturer be
permanently fastened to the gym, for identication in case
of recall or warranty claim. Your Swing Beam comes with
anameplate.Itisimportanttofastenthenameplate tothe
gym.
FitthenameplatenearthecenteroftheBeam.Usethein-
cluded#6x1/2"panheadscrewstoattachthenameplate
totheSwingBeam.
HangtheSwingsinthepositionsshown.
U.S.safetystandardsrequireaminimumclearance
of8"fromthebottomofeachSwingAccessoryto
theground.U.K.(&E.U.)safetystandardsrequire
a minimum clearance of 350mm (13-3/4") be-
tweenthebottomofeachSwingAccessoryand
theground.
TheheightofeachSwingAccessoryisadjust-
ed by using a different link in the chain. Be
sure to hang the Swings Accessories with
ground clearance greater than or equal to
thesafetystandardforyourregion.
IMPORTANT:
When using this Beam with the Northbridge gym, which has a tire swing,
always hang the Ring Trapeze closest to the gym to reduce the possibil-
ity of conict.