BOERPLAY BBPE110.5AP User manual

Multi-play equipment
BBPE110.5AP
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
* Vloerhoogte (Floor height)
1,45 m *
0,00m 2,32m 3,12m 3,18m
0,00 m
0,45 m
0,85 m
0,90 m
0,00 m
1,45 m
1,68 m
2,32 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
6,18m
3,93 m
5,68m
1,00m
0,50m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
0,50 m
1,57m0,40m0,40m1,57m
1,61 m 2,21 m 0,80 m 1,57 m
0,56m
0,27 m
0,25 m
o
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
Boer Basic PlayStaander 1,45m
AA
002
BBP
OD
41
Boer Basic playVloer
AA
004
BBP
OD12
Boer Basic playGlijbaan 1,45m
A007BBPOD13
Boer Basic playRailing
AA009BBPOD44
Boer Basic playKlimwand 1,45m
A012BBPOD15
Boer Basic playInloopnet
AA
018
BBP
OD
1
6
100x100
Paalkap
A
046
BBP
OD
47
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Bouw één keer een toren op uit 1+6, 2 en 4
3 - Assembleer de overige modules met behulp van de moduletekeningen
4 - Plaats 3, verbind deze aan 2
5 - Plaats 5, verbind deze aan twee keer 1
6 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
7 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Assemble one tower out of 1+6, 2 and 4
3 - Assemble the remaining modules using the module drawings
4 - Place 3, attach it to 2
5 - Place 5, attach it to two times 1
6 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
7 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
4
7
3
2
5
1
6

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
Voor ( Front )
Rechts ( Right )
0,00 m
1,45 m
2,24 m
2,32 m
0,00 m
0,44 m
0,69 m
0,94 m
1,19 m
1,45 m
2,24 m
2,32 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 110 5AP
Klimklauter, 1 toren
Boer Basic play
18-6-2014
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
Achter ( Back )
Links ( Left )
0,00 m
0,44 m
0,69 m
0,94 m
1,19 m
1,45 m
2,24 m
2,32 m
0,00 m
1,45 m
2,24 m
2,32 m

LOGBOOK
Type indication Basic Play
Article number BBPE110.5AP
Product Name Multi-play equipment
Maximum fall height 1,5 m
Construction year 2023
Certificate 142748
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 002 A A
Staander 1,45m
Boer Basics
8-10-2014
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
4,8 x 18 - RVS A2-70Klinknagel olkop 052005014BSR
41
1,45m vloerStaander 2,8m 020
BBP
OME
1
2
100 x 100
Voetplaat
AVZP
903
VRB
OME13
2
1
3

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 004 A B
Vloer
Boer Basic play
26-11-2015
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
M10 VZSLUITRING 002010030BSV81
M10 - VZ 8 8
Borgmoer
010010010BSV
4
2
M10 x 190 - VZ 8 8
Zeskantbout ISO 4014
190010021BSV
4
3
Donut wit
Beschermdop M10-M12
020010DONKST84
Dop wit
Beschermdop M10-M12
020010DOPKST85
BOER BASIC PLAYVLOER G004BBPSMD16
6 x 120 - RVS A2-70
Schroef Assy
120006002BSR126 1
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR96 2
LDPE anti-slipVloerplaat
A
007
BBP
KST
1
6 3
Boer Basic PlayLangsregel vloer
B
017
BBP
KST26 4
560mm lang
ReBo 70 x 70 018
BBP
KST36 5
6.16.3 6.2
312
4
5
6.5 6.4

© Copyright BOERplay 31-8-2022 Revision: MOD BBP 007 x
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR

© Copyright BOERplay 31-8-2022 Revision: MOD BBP 007 x
1
/4
A mm
A mm
A = A
0 mm
2
/4
1450 mm
KST.BBP.003.xxx
xxx: 203 Orange
Oranje / Orange / Naranja / Orange
276mm
276mm
20 mm
Ø11mm(3x)
xxx: 502 Blue
Blauw / Blau / Azul / Bleu

© Copyright BOERplay 31-8-2022 Revision: MOD BBP 007 x
BSR.002.005.050
x
1
BSR.011.010.020
x
2
BSR.023.010.050
x
2
BSR.030.010.002
x
2
BSR.035.010.030
x
2
KST.ROR.006.000
x
1
Ø3 x 40mm
Ø11 mm (2x)
B
A (2x)
BSR.011.010.020
BSR.035.010.030
BSR.030.010.002
BSR.023.010.050
KST.ROR.006.000
BSR.002.005.050
Detail A (2x)
Detail B (1x)
4
/4
3
/4

© Copyright BOERplay 22-2-2022 Revision: A MOD BBP 009 x
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR

© Copyright BOERplay 22-2-2022 Revision: A MOD BBP 009 x
SME.BBP.013
x
1
BSR.002.005.050
x
6
KST.ROR.006.000
x
6
BSR.014.005.052
x
6
Metalen staanders
Pfosten aus Metall
Postes de metal
Poteaux en métal
Metal posts
NL
DE
ES
FR
Plastic or wooden posts
NL
DE
ES
FR
Kunststof of houten staanders
Pfosten aus Kunststoff oder Holz
Postes de plástico o madera
Poteaux en plastique ou en bois
Detail A (2x)
1
/1
AA
ø5mm
BSR.014.005.052
18 mm
ø3mm x 30
KST.ROR.006.000
BSR.002.005.050
50 mm
... mm
Check 'order of assembly'
controleer 'Montagevolgorde'
überprüfen Sie die ,Montagereihenfolge'
verifica el 'Orden de esemblado'
vérifiez  Ordre de montage 
NL
DE
ES
FR

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 012 G
Klimwand 1,45m
Boer Basic play
31-3-2014
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
5 x 70 - RVS A2-70
Sc roef Assy
070005002BSR81
ZWARTROZETRING M5 000006RORKST82
Basic PlayKlimwand 1,5m
061003BBPOPE13
2
1
3