BOERPLAY Combination Calisthenics User manual

Combination Calisthenics
FITE015.502
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
A
2,62m
4,87 m
5,46m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
7,95m
7,40m
7,00 m
8,45 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
0,80 m
0,60 m
0,25 m o
1900 1600 1600 800 550 1500
1605
1345
1600
1600
800
1500

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
Staander 2600
502050FITMOD71
Sit-u bank
001051FITMOD12
Vast
Enterrek
001052FITMOD13
h.o.h. 1600
Stang 001053
FIT
MOD6
4
Staander 1400
502057
FIT
MOD2
5
Slang 001060
FIT
MOD
1
6
Staander 2100 502062
FIT
MOD
47
h.o.h. 800
Stang 001063
FIT
MOD
5
8
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De modules met bui en ijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules ijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 1,5,7
3 - Plaats 3,4,6,8 en verbind de e aan 1,5,7
4 - Plaats 2 en verbind de e aan 1,5,7
5 - Controleer of het toestel voldoet aan de afmetingen oals op blad 'afmetingen'
6 - Dicht de gaten en verdicht het and
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1,5,7
3 - Place 3,4,6,8 and attach it to 1,5,7
4 - Place 2 and attach it to 1,5,7
5 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
6 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
7
1
84
2
6 3
1
1 7 7 5 57
1 111

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
0
534
784
0
2034
2534

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE FIT 015 502
Combinatie
Calisthenics
5-1-2016
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
0
1334
2294
2534
0
484
834
1184
1534
1884
2034

LOGBOOK
Type indication
Article number FITE015.502
Product Name Combination Calisthenics
Maximum fall height 1,5 m
Construction year 2023
Certificate 0183402366
Inspection body NVT
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain