BOERPLAY CSPE411.320 User manual

CSPE411.320
S2 Swing

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE CSP 411 320
S2 Schommel
Classic Play
3-3-2015
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
3,57 m
1,03m
>0,35m
0,00 m
2,22 m
2,42 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE CSP 411 320
S2 Schommel
Classic Play
3-3-2015
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
7,80m
2,85 m
4,51 m
1,91m 6,80m
R1,50m
6,58 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE CSP 411 320
S2 Schommel
Classic Play
3-3-2015
BOER
SPEELTOESTELLEN
odemplan Groundplan
0,75 m
Grondmarkering
Ground le el marker
3,34m
1,12m
3,34m
0,40 m 3,72 m 0,40 m
0,29 m o (4x)

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE CSP 411 320
S2 Schommel
Classic Play
3-3-2015
BOER
SPEELTOESTELLEN
Modules Modules
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr
Classic PlayFrame S2 Schommel 320041CSPMOD
11
Ketting 165 alk Ø80Schommelzitje
A
042302CSPMOD22
55 KG
Poer model 2
001002O TMOD
4
3
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 1
3 - Verbind de losse onderdelen met elkaar
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
6 - Hang de schommelzit es (2) op
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
3 - Maat tussen maaiveld en de schommelzit es < 350 mm
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1
3 - Connect the parts
4 - Make sure the device meets the dimensions on sheet 'dimensions'
5 - Close the holes and compacted the sand
6 - Hang up the seats of the swing (2)
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
3 - Distance between groundlevel and the seat of the swing < 350 mm
1
2
Typeplaatje
Identification plate
B
3

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Classic Play
Product code CSPE411.320
Name of equipment S2 Schommel RAL3020
Maximum height of fall 1,5 m
Year of construction 2017
Certificate 07320346570
inspection authority TUV Nord
Langemarckstrasse 20, Essen - 45141 Essen
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment S2 Swing
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
CSPE411.320
S2 Swing

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".