BOERPLAY Fitpoint User manual

Fitpoint
UBG.020.018
Powered by TCPDF (www.tcpdf.org) 1 / 1

Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee

2Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Table of Contents
 Transport page 3
 Dimensions page 4
 Installing the four corners page 5
 Installation/Anchoring page 8
 Floor page 9
 Pillar page 10
 Cables page 11
 Roof page 12
 Weight page 13
 Pulldown, bench press & rower bench page 14
 Abdominal bench page 15
 Abdominal page 16
 Bench Press page 17
 Pull Down page 18
 Rower page 19
 Stepper page 20
 Installing new swing in Stepper page 21
 Twister page 23
 Stepup page 24
 Balance board page 25
 FitPoint parts page 26
 Maintenance instructions page 34
 Guarantee conditions Denfit page 36
 Appendix A Operational Inspection page 39
 Appendix B Annual Main Inspection page 40

3Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Transport
In closed truck
On open truck with crane with pre-assembled Steppers and Twisters
Max. heigth: 2650 mm

4Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Dimensions

5Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Installing the four corners
When delivered in a closed truck the four corner exercises (Stepper, Twister, StepUp
and BalanceBoard) will not be pre-assembled.
The necessary
bolts, washers
and lock nuts are
supplied by Denfit

6Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Installing the four corners
1. Put the Fitpoint on the wooden beams that come with the delivery (image 1)
2. Place the four corners in the right spot position (image 2)
3. Tilt the floor backward and shove it over de pins (image 3a and b)
4. Lift the floor on side of the post so it is parallel with the Fitpoint floor (image 4)
5. Push the bolt through the holes from the inside and screw on the lock nut from the other side
(image 5a and b)
6. Now the floor is installed (image 6)
7. After the four corners are installed, remove the wooden beams
12
3b3a
45a

7Version 2.4
WWW.DENFIT.NL
Service Manual FitPoint
For installation, maintenance, service and guarantee
Installing the four corners
5b 6
7

8Version 2.4
Service Manual FitPoint
For installation, maintenance, service and guarantee
Installation / Anchoring
Anchoring soft surface
Step 1 Step 2 Step 3
Anchoring on hard surface: tarmac
Anchoring on hard surface: concrete
Anchoring on tarmac
with chemical ancho-
ring
Use drill instructions
from your chemical
anchoring
Anchoring on concrete
with wedge anchor
1
4
Pos.nr Part nr. Part descripon Dimension
01 FP3-01 Chem. Floor anchor M12x100
02 FP3-02 Anchoring pin
04 FP3-04 Threaded rod M12x100
The FitPoint has a weight of 1500 kg and therefor anchoring to the ground is not necessary. If an-
choring is desirable, this is how it can be done:

9Version 2.4
Service Manual FitPoint
For installation, maintenance, service and guarantee
FitPoint floor
See parts list