BOERPLAY Multi Swing Anti-wrap H2.13 User manual

Multi Swing Anti-wrap H2.13
BBPE039.0A
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 039 0A
Trippel schommel
BBP
29-11-2023
Hoofdafmetingen Main dimensions
>0,35 m
> 0,40 m
> 0,35 m
0,00 m 1,07 m 3,46 m 6,01 m 9,23 m 12,45 m 15,39 m
0,00 m
0,69 m
1,38 m
0,00 m
2,13 m
2,19 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 039 0A
Trippel schommel
BBP
29-11-2023
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
15,99 m
14,99 m
7,10 m 6,10 m 2,50 m
0,88 m 1,23 m 1,02 m 1,13 m 0,88 m 1,23 m
3,05 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 039 0A
Trippel schommel
BBP
29-11-2023
odemplan Groundplan
Grondmarkering
Ground le el marker
0,27 m 3,49 m 2,55 m 3,22 m 3,22 m 2,98 m 0,26 m
2,79 m
1,54 m2,77 m
0,33 m
0,30 m
0,55 m
0,53 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 039 0A
Trippel schommel
BBP
29-11-2023
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
Overgooi Zitje 1,5 m
Basic Play
G53BBPMOD41
Basic PlayOvergooi Vogelnest
BG540BBPMOD22
Boer Basic playTussenmodule schommel
CA552BBPMOD43
Boer Basic playAanbouwschommel AW
A
5 5
BBP
MOD
14
Midden dubbel zitBovenbalk schommel
A
67
BBP
MOD2
5
AW nestschommelBovenbalk
A
679
BBP
MOD
1
6
Peuterzitje lengte 1.5 mMulti Swing G6 0
BBP
MOD2
7
Boer Basic PlayEindmodule schommel
A
6 2
BBP
MOD1
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Bouw Frame (2+3+4)
3 - Plaats Frame (2+3+4)
4 - Verbind 1 aan 3+4
5 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
6 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Assemble Frame (2+3+4)
3 - Place Frame (2+3+4)
4 - Connect 1 to 3+4
5 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
6 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
Typeplaatje
Identification plate
B
8
1
2
7
3
6
5
5
8
4

LOGBOOK
Type indication
Article number BBPE039.0A
Product Name Multi Swing Anti-wrap H2.13
Construction year 2024
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m
Powered by TCPDF (www.tcpdf.org)