BOERPLAY PSTE110.055 User manual

Multi-play equipment
PSTE110.055
Powered by TCPDF (www.tcpdf.org) 1 / 1

© Copyright BOERplay 12-10-2022 Revision: B PST 110 055
main dimensions
Hoofdafmetingen
Hauptabmessungen
Dimensiones principales
Dimensions principales
NL
DE
ES
FR
0,00 m
0,95 m
1,02 m
1,45 m
1,90 m
2,40 m
< 0,35 m
0,00 m 0,79 m 1,69 m 2,01 m 2,93 m 3,75 m
0,00 m
0,53 m
0,95 m
1,42 m
1,98 m
2,09 m
3,39 m

© Copyright BOERplay 12-10-2022 Revision: B PST 110 055
obstacle free zone
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles
NL
DE
ES
FR
Obstacle free zone - EN-1176
NL
DE
ES
FR
Obstacle free zone
- Specific Law (NL)
NL
DE
ES
FR
Impact area
NL
DE
ES
FR
Obstakelvrije zone - Specifieke wet (NL: WAS)
Hindernissfreie raum - Spezifisches Recht (NL)
Zona libre de obstáculos - Ley especifica (NL)
Zone libre d'obstacles - Loi spécifique (NL)
Obstakelvrije zone - EN-1176
Hindernissfreie raum - EN-1176
Zona libre de obstáculos - EN-1176
Zone libre d'obstacles - EN-1176
Opvangzone
Ausprallbereich
Zona de impacto
Zone d'impact
6,80 m
6,29 m
6,55 m
6,23 m
>1,50m
>1,50m
0,50m1,00m
>1,50m
>1,50m
0,57m
1,51 m

© Copyright BOERplay 12-10-2022 Revision: B PST 110 055
ground plan
Bodemplan
Bodenplan
Plan de superficie
Plan de surface
NL
DE
ES
FR
0,70 m
0,61 m
Grondmarkering
Ground level marker
2,97 m 3,82 m 0,70 m
1,67 m2,16 m1,74 m
1,42 m
1,99 m
0,44 m
0,68 m
0,80 m
0,75 m
0,25 m
2,30 m
1,44 m
0,80 m

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
Vloer 1,45 00201
MAP11
Pasvloer 0,59 en 0,95 m
00401
MAP
12
Grond frame 1,45
14002MAP53
Staander 2,6 m
26004MAP14
Staander 3,1 m
31004MAP35
L = 1,3 m Ra l ng 13005
MAP1
6
L = 1,4 m
Ra l ng
14005
MAP
2
7
Ra l ng
15005MAP18
Ra l ng
16005MAP19
Rek H=900Du kel
09008MAP110
Ladder 0,95 m
095
17MAP111
Module Rob naGl jbaan 145 - 150 cm
B
192002PSTMOD
1
12
© Copyright BOERplay 12-10-2022 Revision: B PST 110 055
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
Typeplaatje
Identification plate
B
12
5
498
7
7
6
10
3
11
1
2
Geleverde modules:
Zie tabel
Montageinstru tie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven spe ifiek de maten van de verbindingen aan
1 - Graaf de gaten volgens het bodemplan
2 - Bouw en plaats toren met 1,2,(5x)3,4,5,6,(2x)7,8 en 9
3 - Plaats 10, verbind deze aan 4
4 - Plaats 11, verbind deze aan 2
5 - Plaats 12, verbind deze aan 1
6 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
7 - Di ht de gaten en verdi ht het zand
Controles:
1 - Corre te opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instru tion:
- The main dimensions indi ate the dimensions of the posts and floors
- The detailed dimensions show the spe ifi dimensions of the onne tions
1 - Dig the holes a ording to the ground plan
2 - Assemble and pla e tower with 1, 2, (5x)3,4,5,6,(2x)7, 8 and 9
3 - Pla e 10, atta h it to 4
4 - Pla e 11, atta h it to 2
5 - Pla e 12, atta h it to 1
6 - Che k that the equipment onforms to the dimensions shown on sheet 'dimensions'
7 - Close the holes and ompa t the sand
Che ks:
1 - Corre t assembly and all the fasteners
2 - Che k the dimensions of the safety area with regard to the play equipment

A ( 1 : 8 )
© Copyright BOERplay 12-10-2022 Revision: B PST 110 055
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
A
0,00 m 0,70 m 1,65 m 2,15 m 3,10 m
< 40 mm
< 0,85 m
> 0,60 m
< 0,85 m
> 0,60 m

LOGBOOK
Type indication Adventure Play
Article number PSTE110.055
Product Name Multi-play equipment
Maximum fall height 1,5 m
Construction year 2023
Certificate 058738
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 002 192 B
Glijbaan 145 - 150 cm
Module Robina
3-1-2013
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M10 - RVS A2-70
Borgdopmoer
020010011BSR
1
M10 x 50 - RVS A2-70
Slotbout
05001002BSR2
M10SLUITRING 002010030BSR 3
145 cm
Glijbaan
B
3204
VRB
SME
14
2
3
1
Let op: toestel bij voorkeur niet met
de glijbaan op het zuiden plaatsen.
Attention: it is advisable not to oriënt
playground equipment with the slide
facing south
4

© Copyright BOERplay 14-2-2023 Revision: MAP 01 002
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M12, L= 260, RVS A2-70
Draadeind+borgm.+ringen+dop
260M12SETMR61
30x30x14
Afstandsbus
001003PSTKST62
Vloer 1,45
A
009063PSTSHO
1
3
3
1
2

© Copyright BOERplay 11-8-2022 Revision: MAP 01 004
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M12, L= 260, RVS A2-70
Draadeind+borgm.+ringen+dop
260M12SETMR61
30x30x14
Afstandsbus
001003PSTKST62
Pasvloer 0,59 en 0,95 vloer
011063PSTSHO13
3
1
2

© Copyright BOERplay 18-7-2022 Revision: MAP 02 140
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M10 X 80HOUTDRAADBOUT 080010022BSV41
M10 x 30 - VZ 8.8Carrosserierin 030010035BSV
4
2
Len te = 1400
Standaard plank 120x20
140211PSTOHO
1
3
1
2
3

© Copyright BOERplay 3-8-2022 Revision: MAP 04 260
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
Zaaglengte = 2600Robinia Ø 14-16
801PSTOHO
11
1

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
Zaaglengte = 3100 mRobinia 14-16
803PSTOHO
11
© Copyright BOERplay 18-7-2022 Revision: MAP 04 310
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
1

© Copyright BOERplay 3-8-2022 Revision: MAP 05 130
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
M12, L= 220, RVS A2-70
Draadeind+borgm.+ringen+dop
220M12SET
BMR
2
1
Leng e =1300
Paal 10-12
013120PSTOHO
1
2
2
1

© Copyright BOERplay 9-8-2022 Revision: MAP 05 140
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
M12, L= 220, RVS A2-70
Draadeind+borgm.+ringen+dop
220M12SET
BMR
2
1
Leng e =1400
Paal 10-12
014120PSTOHO
1
2
2
1

© Copyright BOERplay 18-7-2022 Revision: MAP 05 150
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
M12, L= 220, RVS A2-70
Draadeind+borgm.+ringen+dop
220M12SET
BMR
2
1
Leng e =1500
Paal 10-12
015120PSTOHO
1
2
2
1