BOERPLAY SOLE030.225 User manual

SOLE030.225
Horizontal bar

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 225
Rekstok solo
Pionier
23-1-2017
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
2,20 m
3,50m
R1,50 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 225
Rekstok solo
Pionier
23-1-2017
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
R1,50m
1,75m
1,75m
0,20 m
0,49m
0,57 m 1,07 m 0,57 m
0,76 m
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 225
Rekstok solo
Pionier
23-1-2017
BOER
SPEELTOESTELLEN
A metingen imensions
0,00 m
1,83 m
2,05 m
0,36m
1,19 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 225
Rekstok solo
Pionier
23-1-2017
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
180 cm
Rekstok
000501PNRMOD11
1
Geleverde module :
Zie tabel
Montagein tructie:
- De hoofdmaten geven de maten van de taander en vloeren aan
- De detailtekeningen geven pecifiek de maten van de verbindingen aan
- De module met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige module zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgen het bodemplan
2 - Plaat 1
3 - Controleer of het toe tel voldoet aan de afmetingen zoal op blad 'afmetingen'
4 - Dicht de gaten en verdicht het zand
Controle :
1 - Correcte opbouw en alle beve tiging middelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toe tel
Supplied module :
See table
A embly in truction:
- The main dimen ion indicate the dimen ion of the po t and floor
- The detailed dimen ion how the pecific dimen ion of the connection
- The module which contain tube are dimen ioned at the top of the flange
- Other module are dimen ioned at the top (climbing wall , cap for the po t , etc.)
A embly equence:
1 - Dig the hole according to the ground plan
2 - Place 1
3 - Check that the equipment conform to the dimen ion hown on heet 'dimen ion '
4 - Clo e the hole and compact the and
Check :
1 - Correct a embly and all the fa tener
2 - Check the dimen ion of the afety area with regard to the play equipment

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Pioneer Play
Product code SOLE030.225
Name of equipment Rekstok pionier
Maximum height of fall 1,9 m
Year of construction 2017
Certificate 09100312703
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Horizontal bar
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
SOLE030.225
Horizontal bar

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PNR 501 000
Rekstok
180 cm
9-10-2008
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
180 cm
Rekstok frame
B320202PNRSME12
EI 05
Submodule
000005
PNR
SM21
OPMERKINGBENAMINGRBEH.NR.PROJ.TYPENPOS
1
2