BOERPLAY SOLE030.366 User manual

SOLE030.366
Slide

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 366 A
Glijbaan HHT
Hoogte 195 cm
25-8-2015
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
3,70 m
<0,35m
0,00 m
0,34 m
0,65 m
0,97 m
1,28 m
1,60 m
1,95 m
2,70 m
0,88m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 366 A
Glijbaan HHT
Hoogte 195 cm
25-8-2015
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
6,04m
R1,50m
1,06m
3,57 m
R1,95m
4,42 m
6,54m
R1,59m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 366 A
Glijbaan HHT
Hoogte 195 cm
25-8-2015
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
3,44 m
1,00m
1,17 m 1,94 m
0,60m
1,73m
1,54m
0,30 m 0,25 m
0,75m
0,50m
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 366 A
Glijbaan HHT
Hoogte 195 cm
25-8-2015
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
HHT 195 cmLadder glijbaan
A
538030SOLMO
11
Module HHTGlijbaan 195 cm
193
HHTVRB
MO12
2
1
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoo dmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven speci iek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graa de gaten volgens het bodemplan
2 - Plaats 1,2
3 - Controleer o het toestel voldoet aan de a metingen zoals op blad 'a metingen'
4 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de a metingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions o the posts and loors
- The detailed dimensions show the speci ic dimensions o the connections
- The modules which contain tubes are dimensioned at the top o the langes
- Other modules are dimensioned at the top (climbing walls, caps or the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1,2
3 - Check that the equipment con orms to the dimensions shown on sheet 'dimensions'
4 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the asteners
2 - Check the dimensions o the sa ety area with regard to the play equipment
Typeplaatje
Identification plate
B

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Nature Play
Product code SOLE030.366
Name of equipment Glijbaan HHT hoogte 195cm
Maximum height of fall 1,9 m
Year of construction 2017
Certificate 100315884
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Slide
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
SOLE030.366
Slide

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 030 538 A
Ladder glijbaan
HHT 195 cm
25-8-2015
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
5 x 50 - RVS A2-70
Schroe Assy
050005002BSR34
1
M10 - RVS A2-70
Borgmoer
010010010BSR22
M10 x 80 - RVS A2-70Zeskantbout 080010021BSR23
M10 x 140 - RVS A2-70Zeskantbout 140010021BSR2
4
M10 x 100 - RVS A2-70
Zeskantbout
100010021BSR2
5
M10SLUITRING 002010030BSR46
M10 x 30 x 2,5CARROSSERIERING 030010035BSR87
M5 - RVS A2-70Facet ring 015005036BSR208
M10 x 40DRAADBUS 040M10BUSBSR
4
9
1000 x 300 mm
Ankerplaat
030100
APL
KST110
Donut RoodBeschermdop M10-M12
030010DONKST411
Dop roodBeschermdop M10-M12
030010DOPKST412
Glijbaan 195 cmStaander HHT
HHT061SOLOHO213
Zamak, RAL 5003
PAALKAP 100
ZMK
100
KAP
OME2
14
100 x 100
Voetplaat
C
VZP
903
VRB
OME215
Glijbaan
ZijwangA
030066SOLOPE216
vrijstaande glijbanenStartplateau 003SOLSMD
117
Ladder glijbaanSysteembuis
320237SOLSME
5
18
16
5611 12
9
3 11 62 12
947
13
14 1
18
18
17

B
BB
Be
ee
en
nn
na
aa
am
mm
mi
ii
in
nn
ng
gg
g
Title
O
OO
Op
pp
pm
mm
me
ee
er
rr
rk
kk
ki
ii
in
nn
ng
gg
g
Comment
D
DD
Da
aa
at
tt
tu
uu
um
mm
m
Date
T
TT
Te
ee
ek
kk
ke
ee
en
nn
ni
ii
in
nn
ng
gg
g
Drawing
MOD VRB HHT 193
Glijbaan 195 cm
Module HHT
3-12-2008
BOER
S
SS
SP
PP
PE
EE
EE
EE
EL
LL
LT
TT
TO
OO
OE
EE
ES
SS
ST
TT
TE
EE
EL
LL
LL
LL
LE
EE
EN
NN
N
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
BORG RVS M10DO MOER 020010011BSR61
M10 x 40 - RVS A2-70Slotbout 040010026BSR62
M10 - RVS A2-70Carrosserie ring 030010035BSR63
195 cm
Glijbaan
C320614
VRB
SME1
4
2
4
3
1
Let op: toestel bij voorkeur niet met
de glijbaan op het zuiden plaatsen.
Attention: it is advisable not to oriënt
playground equipment with the slide
facing south