Bolderton 716240 User manual

Congratulations on your Bolderton purchase.
You demand the best in outdoor gear, and Bolderton delivers with professional-grade
quality and performance that keep you at the top of your game.
350LB Bear Treestand
Item #716240
sportsmansguide.com
For assistance with your product, please contact Sportsman’s Guide customer
service at 1-800-888-3006 Mon.-Fri. 7:00am to 9:00pm, Sat.-Sun. 8:00am to 8:00pm
CST or go to sportsmansguide.com/customerservice/contactus

ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the ASTM F2123 - Standard Practice for Treestand Instructions.
LADDERSTAND USAGE INSTRUCTIONS & WARNINGS
WARNING!
Failure to read and strictly comply with the instructions contained in this
Instruction Manual may result in serious injury or death!
WARNING! A “Treestand Safety: It’s Up To You” DVD has been included with this
treestand. Please view it in its entirety prior to using this or any other Bolderton
product(s). Failure to follow these instructions may result in serious injury or death!
WARNING! Prior to each hunt, you must inform someone of your hunting location,
Failure to follow these instructions may result in serious injury or death!
WARNING! THE SAFE USE AND OPERATION OF THIS PRODUCT(S) IS THE SOLE RE-
SPONSIBILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER TO PROVIDE
ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT(S) WITH THESE INSTRUCTIONS
AND THE AFOREMENTIONED A “
TREESTAND SAFETY: IT’S UP TO YOU” DVD. FAILURE TO
FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! ADDITIONALLY,
FAILURE TO FOLLOW THIS INSTRUCTION MAY SUBJECT YOU TO PERSONAL LIABILITY
PENALTIES AS DETERMINED BY THE U.S. JUDICIAL SYSTEM.
WARNING! Prior to each hunt, make sure that you have a signaling device (e.g.,
and in an operable condition. This device must be within easy a
mobile phone, radio, whistle, signal ˜are or personal Locator Device (PLD) in your possession
ccess should you experience
the need to contact emergency assistance. Failure to follow these instructions may
result in serious injury or death!
GGL31-B ∙ 350LB Bear Treestand
CARRYING CAPACITY 350 lbs/159 kg
952-955-9263 for replacement of any damaged or missing parts.
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING THE GROUND.
THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR YOUR PERSONAL
SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT INSTRUCTION MANUAL IN ITS
ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-UP, INSTALL AND/OR OTHERWISE USE
THIS BOLDERTON PRODUCT. AT LEAST ANNUALLY, REVIEW THE CONTENTS OF THIS INSTRUCTION
MANUAL AND WATCH THE SAFETY TREESTAND HUNTING DVD. ADDITIONALLY, KEEP THESE
INSTRUCTIONS FOR THE ENTIRE DURATION THAT YOU OWN THIS PRODUCT(S). FAILURE TO
FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING! This product carries strict weight restrictions. Please note that these weight
limitations include the user(s) and their equipment. DO NOT use these product(s) if you
exceed these total weight limitations. Failure to follow these instructions may result in
serious injury or death!
A safety treestand hunting video, Treestand Safety: It’s Up To You, has been included.
Please view it in it’s entirety prior to using this product! Thank you for your purchase of this
quality Bolderton product. To ensure your personal safety, please take a moment to
carefully read this Instruction Manual in it’s entirety before attempting to assemble, set-
up, install and/or otherwise use this Bolderton product. Failure to follow these
instructions may result in serious injury or death!
Should you have any questions about the installation and/or use of this product, or
any other Bolderton product(s) do not hesitate to call one of our customer service
repre- sentatives 800-888-3006 or visit Bolderton online at
sportsmansguide.com. Our customer service representatives will answer any
questions you may have about any of the complete line of Bolderton products.
Do not return this product to the retailer if you have any damaged or missing parts. Call
WARNING! Do not remove, modify, and/or omit any portion or otherwise mechanically
and/or part substitution shall immediately void your factory warranty and may result
in serious injury or death! If you suspect that a part(s) is missing and/or defective,
please call 952-955-9263 for replacement of missing or defective parts. Please have the
product) before calling to better assist you. Never modify your stand in any way by
making repairs, or altering, adding or attaching anything to it except if explicitly authorized
in writing by Bolderton. ALWAYS USE GENUINE FACTORY AUTHORIZED
BOLDERTON REPLACEMENT PARTS. USE OF ANY REPLACEMENT PARTS OTHER
THAN GENUINE BOLDERTON PARTS VOIDS YOUR WARRANTY AND MAY RESULT
IN SERIOUS INJURY OR DEATH!
WARNING! ALWAYS inspect/check ALL
expiration dates/tags on all straps (e.g., tree
belt, tether/lanyard, etc.) and the full-body fall arrest harness and its components
prior to each use. You must replace
ALL straps and suspension seats EVERY year.
Never use any strap(s) or full-body fall arrest harness that has expired and/or is showing
any signs of damage and/or wear. Failure to follow these instructions may result in serious
injury and death!
WARNING!
Make certain all chains, cable straps, etc. are tightened per this Instruction
Manual prior to use. All treestand bark biters must be in contact with the tree before
you step onto the stand. The correct adjustment and tightening of attachment hardware
(as outlined in each individual instructions) is critical to the stable installation of the
ladderstand(s). Additionally, you MUST be wearing your Fall Arrest System (FAS) which
includes a full-body fall arrest harness, tree belt, lanyard/tether, suspension relief device
and climbing belt/linesmen belt (as applicable) in accordance with the Instructions
contained in this Instruction Manual. Failure to follow these instructions may result
in serious injury or death!
WARNING!
This product(s) is designed for adult use only. No one under the age of
16 shall attempt to use this or any other Bolderton product(s) without direct adult
supervision. Failure to follow these instructions may result in serious injury or death!
WARNING! Prior to attempting to use this or any other Bolderton product(s),
you must take a moment and become familiar with its assembly, setup and installation.
You must practice installing, setting up and using your full-body fall arrest harness and
its components (i.e., lanyard/tether, tree belt, suspension relief device, climbing belt
(as applicable)) at ground-level prior to attempting to use it at heights above ground-
level. Once you have become thoroughly knowledgeable and comfortable with this
Bolderton product(s) setup, installation and use at ground-level, you are now ready
to use it at heights above ground-level. Failure to follow these instructions may result
in serious injury or death!
WARNING! Several Bolderton products are equipped with a footrest, armrests,
backrests and/or shooting rail. Neither the footrest, armrests, backrests nor the
shooting rail have been designed to support the users weight. Under no circumstances
Doing so will put the user in serious risk of injury or death. Failure to follow these
instructions may result in serious injury or death!
WARNING! You must wear a Full Arrest System (FAS) comprising of a full-body fall
arrest harness, tree belt, lanyard/tether, suspension relief device and climbing belt/
lineman’s belt (as applicable) at all times after leaving the ground. You must stay connected
at all times after leaving the ground while using fixed position treestands. Single safety
belts and chest harness are no longer allowed and should never be used. If you are not
wearing a full-body fall arrest harness that is properly attached to the tree to protect
you from a fall, do not leave the ground nor attempt to enter your treestand. Failure
to follow these instructions may result in serious injury or death!
WARNING! Never attempt to climb up or down with a weapon and/or gear in your
modify this Bolderton product(s) or its assemblies in any manner. Modiÿcation, misuse,
possession. ALWAYS unload your weapon and pull it up to hunting height using a
tether or pull up rope. ALWAYS lower your unloaded weapon down to the ground
prior (when raising or lowering firearms, the chamber must be open and the barrel pointing
toward the ground) to attempting to climb up or climb down. Use this same method
when raising or lowering all other gear. Failure to follow these instructions may result in
serious injury or death!
1

WARNING! DO NOT
use this or any other Bolderton products(s) if you have a history
of heart problems, back problems, impaired vision, joints that lock-up, spinal fusions,
equilibrium problems, high blood pressure, are not well-rested and/or any other
physical impairment that may limit your ability to use and/or operate this product(s)
in the safe manner outlined in this Instruction Manual. Additionally, do not use this
or any other Bolderton product(s) if you are currently taking medication (including
prescription) and/or using and/or consuming any substance, including alcohol, that
may limit your ability to use this Bolderton product(s) as outlined and described in
the Instruction Manual. Never use a treestand when feeling ill, nauseous or dizzy.
Failure to follow these instructions may result in serious injury or death!
WARNING! DO NOT leave your Bolderton product(s) installed for more than two
weeks (14 days). Any number of factors can jeopardize its installation and integrity.
These include, but are not limited to, weather or other environmental factors that
can negatively a˜ect its performance. Animals can also cause damage to your
Bolderton product(s) that can negatively a˜ect its performance and your safety.
Additionally, factors such as tree growth can stress and damage supporting straps,
chains and/or buckles. Failure to follow these instructions may result in serious injury
or death!
Failure to follow these instructions may
WARNING!
Strict weight limitations have been set for each product(s) to ensure
your personal safety. Note the weight limitations and maximum occupancy for your
Bolderton product(s). This weight limit includes the user(s) and equipment. NEVER
EXCEED THESE WEIGHT LIMITATIONS!
result in serious injury or death!
WARNING! DO NOT attempt to use this or any other Bolderton product(s) when
ice, snow, and/or freezing rain has deposited or formed on any portion of the tree
or stand you intend to climb. Do not attempt to use this or any other Bolderton
(8 km). Do not attempt to use this or any other product(s) when any other adverse
weather condition(s) presents itself. These include, but are not limited to, weather
conditions which have the potential for producing winds, lightning, rain, snow,
sleet and/or any other atmospheric condition which may limit the user’s ability to
operate this Bolderton product(s) in a safe manner as described in this Instruction
Manual. Shall inclement weather conditions arise during your use of this Bolderton
product(s), return to the ground immediately and seek proper man-made shelter.
Failure to follow these instructions may result in serious injury or death!
WARNING! BEFORE each use, make sure all nuts and bolts are secure. CHECK all
hardware and webbing prior to every use to make sure that no damage has occurred to
into contact with any sharp edges. DO NOT USE THIS PRODUCT IF ANY DAMAGE IS
SUSPECTED. Failure to follow these instructions may result in serious injury or death!
hardware and that webbing (as applicable) is not cut or frayed. Keep webbing from coming
WARNING! REPLACE
ment straps every year and when not in use store in a dry, cool, safe place away from
sunlight. Never store a treestand or any of its components outdoors when not in use.
To purchase parts please call 952-955-9263.
Failure to follow these instructions may
result in serious injury or death!
any damaged or worn part with original parts. Replace attach-
WARNING! ALWAYS wear the appropriate foot wear when using a treestand. A good
non-slip safety boot is important for your safety. Be especially careful that boot laces
do not get hooked on the treestand (or any of its components) or climbing aids (tuck
shoelaces into boot before climbing). Failure to follow these instructions may result
in serious injury or death!
WARNING!
serious injury or death!
set the ladder ÿrmly into the ground.
Failure to follow these instructions may result in
WARNING! Check the ground under ladderstands and climbing systems to make
may result in serious injury or death!
WARNING! ALWAYS maintain three-point contact when climbing up/down a tree
when using climbing aids and/or ladderstands. Proper three-point contact means
having either two feet with one hand or one foot with two hands on the step
portion of the climbing aids at all times when climbing up or down. Failure to follow
these instructions may result in serious injury or death!
WARNING!
Prior to each use thoroughly inspect the treestand (and its components)
and all safety devices each time before use for signs of wear, rot, corrosion, cracks, deterioration
and/or any other type of defect(s). Make certain that your treestand is tight and secure
prior to use. Protect this product(s) from extended exposure to direct sunlight, excessive
heat or freezing temperatures by storing inside when not in use. Do not use this or
any other product(s) if it shows evidence of wear, rot, corrosion, cracks, deterioration
and/or any other type of defect(s). Failure to follow these instructions may result in
serious injury or death!
WARNING! DO NOT
attempt to make adjustments to this product while in the
treestand. All adjustments must be made with the entire treestand on the ground.
Failure to follow these instructions may result in serious injury or death!
WARNING!
ALWAYS inspect the treestand and all of its related components, sticks
and all safety devices prior to each use. DO NOT use this product if it shows signs of wear,
damage, deterioration, or vandalism. Factors such as tree growth, vandals, weather and
animals may a˜ect the performance of an unattended
treestand. Failure to follow these
instructions may result in serious injury or death!
WARNING! DO NOT
and written instructions from the manufacturer. Failure to follow these instructions will
in any way. Additionally, do not attach anything to your treestand without explicit authorized
void your warranty and may result in serious injury or death!
WARNING!
DO NOT use this product, or attempt to use a treestand, on a dead, leaning,
DO NOT use this product on any tree that does not allow for a level standing platform.
Failure to follow these instructions may result in serious injury or death!
WARNING! NEVER
hunt out of a treestand at heights at which you are not completely
comfortable. Depending on the tree and hunting conditions, choose the minimum
hunting height that allows for safe, e˜ective hunting. Failure to follow these instruc-
tions may result in serious injury or death!
WARNING!
DO NOT use this, or any other Bolderton produc t(s) to climb utility poles,
telephone poles, structural columns or any other man-made structures. Never use this or
any other Bolderton product(s) around power generation (e.g., transformers, generators,
substations, etc.) and/or power transmission equipment. Never use a treestand on a dead,
leaning, diseased or loose barked tree. NEVER USE A TREE BRANCH, OR ANY PORTION
OF A TREE, TO SUPPORT ANY PORTION OF YOUR WEIGHT OR AS A HAND HOLD. Failure
to follow these instructions may result in serious injury or death!
WARNING! DO NOT jump or bounce on the treestand platform and/or the seat to
engage the stand to the tree. Failure to follow these instructions may result in serious
injury or death!
WARNING! DO NOT stand on the treestand seat. Failure to follow these instructions
may result in serious injury or death!
WARNING! These Bolderton product(s) were designed for installation on trees
with a minimum diameter of nine (9) inches (23 cm) and a maximum diameter of (20)
inches (51cm) at treestand installation height (i.e., seat height). DO NOT use your
Bolderton product(s) on trees with trunk diameters that do not meet this minimum/maxi-
mum diameter requirement. Failure to follow these instructions may result in serious
injury or death!
WARNING! A minimum of three (3) adults is required to install and/or remove a
ladderstand. Failure to follow these instructions may result in serious injury or death!
WARNING!
ALWAYS lean forward as you climb and attach your full-body fall arrest
harness tree belt to the tree trunk before securing the platform to the tree and stepping
onto the platform. Failure to follow these instructions may result in serious injury or death!
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the ASTM F2123 - Standard Practice for Treestand Instructions.
When installing a ladderstand, always apply weight on the ÿrst rung to
3

ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
STEP 1. Identify the main parts of the full-body fall arrest harness (Fig. 1). Hold the
full-body fall arrest harness by the tether loop insuring the harness is upright and leg
straps are hanging down. Straighten any parts that have become twisted. Insert arms
through each shoulder strap (Fig. 2).
STEP 2. Feed the left leg strap between legs and thread through the bottom left
waist loop. Repeat with the right leg strap, feeding between legs and through right
waist loop (Fig. 3).
STEP 3. Secure the two leg straps by threading the three bar buckle (Fig. 4). Tighten
the leg straps snugly. DO NOT
legs. Full-body fall arrest harness shall look like the one depicted in Figure 5 when donned
correctly.
FULL-BODY FALL ARREST HARNESS INSTRUCTIONS
FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS & WARNINGS
WARNING! Failure to read and strictly comply with the instructions contained
here may result in serious injury or death!
READ THE FULL-BODY FALL ARREST HARNESS SECTION CAREFULLY AND FOLLOW
ALL OF THE INSTRUCTIONS! YOUR FULL-BODY FALL ARREST HARNESS AND ITS
COMPONENT (I.E., LANYARD/TETHER, TREE BELT, CLIMBING BELT (LINEMAN’S BELT
AS APPLICABLE), SUSPENSION RELIEF DEVICE) IS DESIGNED FOR A MAXIMUM
CAPACITY (USER AND EQUIPMENT) OF 350 POUNDS (158kg). ADDITIONALLY, YOUR
FULL-BODY FALL ARREST HARNESS (AND ITS COMPONENTS) MUST BE REPLACED
AFTER FIVE (5) YEARS OF SERVICE!
WARNING!
Prior to attempting to use this or any other Bolderton product(s)
you must take a moment and become familiar with its assembly, setup installation, use
and removal. You must practice installing, setting-up and using your full-body fall arrest
harness and its components (i.e., lanyard/tether, tree belt, suspension relief device,
climbing belt/lineman’s belt [as applicable]) at ground-level prior to attempting to use
it at heights above ground-level. Once you have become thoroughly knowledgeable and
comfortable with this product(s) assembly, setup, installation, use and removal at ground-
level, you are now ready to use it at heights above ground-level. Failure to follow these
instructions may result in serious injury or death!
WARNING!
You must wear a F all Arrest System (FAS) comprising of a full-body
fall arrest harness, lanyard/tether, tree belt, suspension relief device and climbing
belt/lineman’s belt (as applicable) at all times after leaving the ground. You must stay
Single safety belts and chest harness are no longer allowed and shall never be used.
If you are not wearing a full-body fall arrest harness (that is connected to the tree)
that is protecting you from a fall, do not leave the ground. Failure to follow these
instructions may result in serious injury or death!
WARNING!
ALWAYS practice using your full-body fall arrest harness (FAS) in the
presence of a responsible adult prior to using it in an elevated hunting environment,
and learn what it feels like to hang suspended in the harness at ground level. Practice
installing and using your treestand at ground level and with a responsible adult present
before you go hunting.
WARNING!
The length of the full-body fall arrest harness lanyard/tether must be
kept to a minimum at all times during use. It shall be adjusted so that it is above the
head with no slack (snug) in the sitting position and you shall have the minimum
amount of slack possible when climbing. Never let the tether strap get under your
chin or around your neck. Failure to follow these instructions may result in serious
injury or death!
WARNING!
Shall you experience a fall there is time to make a correct decision
on what action needs to take place. It is important to remember: DO NOT PANIC!
Failure to follow these instructions may result in serious injury or death!
WARNING!
If you have a limiting physical and/or health condition that precludes
and/or renders you incapable of self-recovery and/or a suitable escape plan is not
available, DO NOT hunt from heights above ground-level. Failure to follow these instructions
may result in serious injury or death!
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING
THE GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR
YOUR PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT
INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-
UP, INSTALL, REMOVE, AND/OR OTHERWISE USE THIS BOLDERTON PRODUCT(S ). AT
LEAST ANNUALLY, REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL AND
WATCH THE “TREESTAND SAFETY: IT’S UP TO YOU” DVD. ADDITIONALLY, KEEP
THESE INSTRUCTIONS FOR THE ENTIRE DURATION THAT YOU OWN THIS BOLDERTON
PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY
OR DEATH!
WARNING! THE SAFE USE AND OPERATION OF THIS BOLDERTON PRODUCT IS THE
SOLE RESPONSIBILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER
TO PROVIDE ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT FROM
THEM WITH THESE COMPLETE INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH! ADDITIONALLY, FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY SUBJECT YOU TO PERSONAL LIABILITY PENALTIES AS DETERMINED
BY THE U.S. JUDICIAL SYSTEM.
WARNING! Practice the use of your Bolderton full-body fall arrest harness and
Suspension Relief Device (SRD) at ground-level, in the presence of a responsible
adult to experience the feeling of hanging suspended before using in a hunting
environment. Failure to follow these instructions may result in serious injury or death!
WARNING!
NEVER allow the full-body fall arrest harness lanyard/tether to get under
your chin or around your neck. This poses a choking hazard that can lead to serious injury
or death. Failure to follow these instructions may result in serious injury or death!
WARNING! If your hunting location is unknown by anyone and communication
for self-recovery/escape shall
you experience a fall. Prolonged suspension in a full-body fall arrest harness can be fatal.
It is important to exercise the legs by pushing against the tree or doing other forms
of continuous leg exercises to avoid blood pooling while being suspended. Varying
degrees of physical ÿtness may require di°erent plans for self-recovery/escape and
to counter the e°ects of prolonged suspension. Have a personal plan and practice
it in the presence of a responsible adult before leaving the ground. No one escape/
rescue plan will work for every hunter, on every tree, in every circumstance. Only you
can determine the best self-recovery/escape plan for your hunting situation before
leaving the ground. There
is time to make a correct decision on what action to take if
a fall occurs while wearing a full-body fall arrest harness. It is important to remember,
DO NOT P ANIC. Remain calm and implement your practiced rescue, relief and recovery
plan. Hunt from the
ground when self-recovery /escape ability is absent. Failure to follow
these instructions
may result in serious injury or death!
WARNING!
READ THESE FULL-BODY FALL ARREST HARNESS INSTRUCTIONS
CAREFULLY AND FOLLOWALLTHE INSTRUCTIONS! YOUR NEW FULL-BODY FALL
ARREST HARNESS IS DESIGNED FOR A MAXIMUM CAPACITY (USER ANDEQUIPMENT)
OF 350 POUNDS (158 kg). ADDITIONALLY, YOUR NEW FULL-BODY FALL ARREST
HARNESS MUST BE REPLACED AFTER FIVE (5) YEARS OF SERVICE! REPLACE
YOUR FULL-BODY FALL ARREST HA RNESS IMMEDIATELY SHALL YOU EXPERIENCE
A FALL WHILE WEARING IT.
WARNING!
You must use the full-body fall arrest harness provided with this product
or a harness that complies with ASTM standards. NOTE: You must store your full-body
fall arrest harness out of direct sunlight and out of any other
harsh environmental
condition(s) that may adversely a°ect its performance. Failure
to follow these
instructions may result in serious injury or death!
4

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
STEP 4. Once you have reached your desired height, insert the tree belt through
the loop of the tether (Fig. 5). Then, carefully wrap the tree belt around the tree
at a height that allows just enough slack for you to sit comfortably in your stand.
Keeping the tether as short as possible limits the distance you will travel, in the
unlikely event you shall experience a fall. To secure the tree belt, insert the free
end up through the slot in the buckle closest to opposite end of the tree belt, then
cross over the sliding mechanism and back down through opposite slot. Pull on tree
belt to secure and test to make sure sliding mechanism engages, creating secure tree
belt placement (Fig. 6, 7, 8).
WARNING!
It is very important to complete this Step of the assembly. An improperly
secured buckle may cause full-body fall arrest harness failure resulting in serious
injury or death! If there is not enough strap available to complete this step, DO
NOT USE THIS FULL-BODY FALL ARREST HARNESS! You may need to purchase
and use a larger specialty sized full-body fall arrest harness that complies with ASTM
standards.
tree
belt
Tree Belt
Side View
Slot A
Left Leg
Strap
Right Leg
Strap
3 Bar
Buckle
Up through Slot B
Down through Slot A
Down through Slot B
Pull tight to secure
Back over top
Slot B
FIG 4
FIG 6 FIG 8
FIG 7
Sitting/
Seating
tree
belt
tether
tree
belt
Standing
tether
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 2
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 3
Tether
Tether
Loop
Tether
Loop
3 Bar
Buckle
3 Bar
Buckle
Front View Rear View
SRD Strap
Right
Waist
Loop
Right
Leg Strap Right
Leg Strap
Left
Leg Strap
Left
Leg Strap
Left
Waist
Loop
Tether
SRD Strap
FIG 1
tree belt
tether
FIG 5
5

ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
Although no one plans to fall from their treestand, falls can and do occur without
warning. It is important to become familiar with the guidelines below and
practice your recovery plan at ground-level. Failure to read, understand, and
follow these steps may result in serious injury or death!
WARNING!
There is time to make a correct decision on what action to
take if a fall occurs while wearing a full-body fall arrest harness. It is important
NOT TO PANIC! Remain calm and implement your practiced rescue, relief
and recovery plan. Failure to follow these instructions may result in serious
injury or death!
WARNING! A suspension relief device must be on your person and readily
accessible while using a full-body fall arrest harness. These devices will allow
you to relieve the load on the lower extremities if suspended in a full-body fall
arrest harness and help maintain circulation in the legs and mitigate (minimize)
suspension trauma (blood pooling), or allow descent to the ground. Follow all
instructions below regarding the provided SRD (Suspension Relief Device)
Failure to follow full-body fall arrest harness instructions could result in not
being able to return to the stand and being suspended in a full-body fall
arrest harness after a fall. Failure to follow these instructions may result in serious
injury or death!
STEP 1.
After a fall, take a moment to catch your breath and stay calm. DO NOT PANIC.
STEP 2. Pull on the SRD strap located on the front right side of your full-body
fall arrest harness (Fig. 9).
STEP 3. Adjust the SRD strap so that you are able to step into the loop and
then stand up, relieving the pressure on your lower extremities. The loop size
can be adjusted by moving the buckle up or down (Fig. 10 and 11).
STEP 4.
If you are able to reach your ladder or climbing system, use it to get
back into your secured treestand and then carefully climb down to ground-
level. If you are not able to reach your stand, remain calm and continue to stand
in the SRD loop until help arrives (Fig. 12).
STEP 5.Use your personal locating device or cell phone to call for help.
NOTE:
or self-extraction from a fall when suspended in a full-body fall arrest harness.
Some systems automatically descend the user while others allow user control.
One of these products/systems can be considered for use as an additional
safety precaution against prolonged suspension and suspension trauma. Be sure
to follow the manufacturers’ directions on the safe use of these products/systems.
STEPS TO FOLLOW IF A FALL WERE TO OCCUR:
Should you have any questions about the assembly, installation or use of this Bolderton product, or any other
Bolderton products, please do not hesitate to call one of our customer service representatives at 800-888-3006 and
they will answer all questions you may have about any of the complete line of Bolderton products.
FIG 9
FIG 10
FIG 11 FIG 12
6

XP15-0581 Ratchet Strap (A) 1
XP16-0547 Seat Bar 1
XP15-0584 Ratchet Strap (B) Assembly 1
XP15-0587 Ratchet Strap (C ) 1
GG10 - 0008
Full-Body Fall Arrest Harness J350 1
XP15-0020 Safety DVD 1
GG20 -0801 Instruction Manual for the GGL31-B
1
XP87-0003 5/16" x 3 1/2" Hex Bolt (G) 2
XP87-0005 1/4" x 1 1/4" Hex Bolt (A) 2
XP87-0007 1/4" x 1 1/2" Hex Bolt (B ) 6
XP87-0009 1/4" x 1 3/4" Hex Bolt (C)
XP87-0012 1/4" x 2" Hex Bolt (D ) 3
XP87-0014 1/4" x 2 1/4" Hex Bolt (E) 6
XP87-0016 1/4" x 3 1/4" Hex Bolt (F) 2
XP87-0018 1/4" x 2 1/2" Carriage Bolt (I) 2
XP87-0020 1/4" Delta Bolt (M) 2
XP87-0025 3/8" Nylon Spacer (K) 2
UP77-0002
Nylon Washer
XP87-0029 1/4" Nylock Nut
XP87-0032 1/4" Wiz Nut (N) 1
XP87-0034 1/4" Delta Nut (L) 2
XP87-0036 Silent Snap Pins 10
XP87-0038 1/4" Wing Nut (O) 2
XP87-0040 Allen Wrench 1
XP87-0043 Seat Tension Bolt 1
XP87-0045 1/4" x 4 1/4" Eye Bolt (J) 2
XP87-0047 5/16" Nylock Nut 4
GGL31-B ∙ 350LB Bear Treestand- PARTS LIST
XP15-0500 Ladder Section D 1
XP15-0503 Ladder Section C 1
XP15-0506 Ladder Section B 2
XP15-0508 Ladder Section A 1
XP15-0509 Lower Bark Biter Tree Brace 2
XP16-0512 Lower Bark Biter Ladder Brace 2
XP17-0502 Right Top Ladder Extension 1
XP17-0503 Left Top Ladder Extension 1
XP16-0518 Left Side Frame 1
XP 20 -0521 Right Side Frame 1
XP 20 -0524 Left Backrest Support 1
XP 20 -0527 Right Backrest Support 1
XP15-0530 Armrest 2
XP15-0533 Left Shooting Rail Stop 1
XP15-0536 Right Shooting Rail Stop 1
XP15-0539 Rear Frame Support 1
XP15-0542 Jaw 2
XP15-0555 Footrest 1
GG20 -0548 Seat Assembly 1
XP16-0550 Front Foot Platform 1
XP16-0551 Rear Foot Platform 1
XP15-0554 Left Shooting Rail Piece 1
XP15-0557 Right Shooting Rail Piece 1
XP15-0560 Shooting Rail Foam 1
GG20 -0563 Shooting Rail Cover 1
XP15-0566 Armrest Foam 2
GG20 -0569 Armrest Cover 2
XP15-0572 Accessory Hooks 1
XP15-0575 Drink Holder 1
XP15-0578 Jaw Tightening Cable 2
XP16-0535 Under Support Gusset 2
Part # Description Qty Part # Description Qty
7
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
ATTENTION!! WHEN YOUSEE A " WARNING!" BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
5
58
23

NOTE: Part illustrations are for reference purposes only, and may not be to actual size.
GGL31-B ∙ 350LB Bear Treestand - HARDWARE DIAGRAM
8
{A} 1/4" x 1 1/4" Hex Bolt
[2 pieces]
{E} 1/4" x 2 1/4" Hex Bolt
[6 pieces]
{J} 1/4" x 4 1/4" Eye Bolt
[2 pieces]
{N} 1/4" Wiz Nut
[1 piece]
{O} 1/4" Wing Nut
[2 pieces]
1/4" Nylock Nut 5/16" Nylock Nut
[4 pieces]
{K} 3/8" Nylon Washer
[ 58 pieces]
Nylon Washer
{L} 1/4" Delta Nut
[2 pieces]
{M} 1/4" Delta Bolt
[2 pieces]
Silent Snap Pin
[10 pieces]
Seat Tension Bolt
[1 piece]
Allen Wrench [1 piece]
Ratchet Strap A [1 piece]
Ratchet Strap C [1 piece]
Ratchet Strap B [1 piece]
{F} 1/4" x 3 1/4" Hex Bolt
[2 pieces]
{G} 5/16" x 3 1/2" Hex Bolt
[2 pieces]
{I} 1/4" x 2 1/2" Carriage Bolt
[2 pieces]
{B} 1/4" x 1 1/2" Hex Bolt
[6 pieces]
{C} 1/4" x 1 3/4" Hex Bolt {D} 1/4" x 2" Hex Bolt
[3 pieces]
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
[ 5 pieces] [3 pieces]
[ 23 pieces] [
2 pieces]

NOTE: Steps 1-9 require you temporarily finger
tighten nuts to insure proper alignment.
FIGURE 1
9
Tab
Left Side
Frame
Top Ladder
Extension
Left
Ladder
Section A
Top Ladder
Extension
Right
Right Side
Frame
[B]
[B]
[B] [B]
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
STEP 1. Attach the Right and Left Top
Ladder Extensions to the Ladder Section
A using two (2) 1/4" x 1 1/2" Hex Bolts
(B), four (4) Nylon Washers and two (2)
1/4" Nylock Nuts. Note: When attaching
the Right and Left Top Ladder Extensions
be sure the bends are facing out and the
Tabs behind. Next attach the Side
Frames to the Top Ladder Extensions
using two (2) 1/4" x 1 1/2" Hex Bolts (B),
four (4) Nylon Washers and two (2) 1/4"
Nylock Nuts. (Fig. 1)

10
FIGURE 2
WARNING! Armrests are provided for comfort and should be used as armrests only. The armrests are not
designed to carry the full weight of the user. Never place more than fifteen (15) lbs of force on the armrests.
Failure to follow these instructions may result in serious injury or death!
STEP 2. Slide the Left and Right Shooting Rail Stops over the front of the Armrests
and secure using two (2) 1/4" Delta Bolts (M). Next insert1/4" x 2 1/2" Carriage
Bolts (I) in top hole in rear of Armrest facing outward (Fig. 2)
STEP 3. Insert the Rear Frame
Support into the Side Frame
aligning holes. Next connect
the Left and Right Backrest
Supports, then attach the as-
sembled Backrest Support to
the Side Frames and Armrests
using two (2) 1/4" x 3 1/4"
Hex Bolts (F), four (4) Nylon
Washers and two (2) Nylock
Nuts. Note: the lower holes
are used in the Armrests and
Backrest Support. The bends
of the Backrest are to angle to
the rear. Next attach the front
of the Armrests to the outside
of the Side Frames using two
(2) 1/4" x 2 1/4" Hex Bolts (E) ,
four (4) Nylon Washers and
two (2) Nylock Nuts. (Fig. 3)
Armrest
Armrest
Rear Frame
Support
Right Side
Frame
Left Side
Frame
Left Backrest
Support
Right Backrest
Support
FIGURE 3
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

11
STEP 5. Insert the Seat Bar though
the front of the Seat Assembly and
secure using one (1) 1/4” x 1 1/4”
using two (2) 1/4” x 1 1/2” Hex Bolts
(B), six (6) Nylon Washers and two
(2) 1/4” Nylock Nuts. (Fig. 4)
FIGURE 4
FIGURE 4A
WARNING! Footrests are provided for comfort and should be used as footrests only. The footrests are not
designed to carry the full weight of the user. Never place more than (15) lbs of force on the footrest. Failure
to follow these instructions may result in serious injury or death!
STEP 4. Using three (3)1/4“x 1
3/4” Hex Bolts (C), six (6)Nylon
Washers and three (3)1/4“
Nylock Nuts, connect the
Front Foot Platform, Rear Foot
Platform and the Under
Support Gussets together.
Making sure to attach the top
of the Under Support Gussets
to the outside bolts. Then
attach the Footrest and Front
Foot Platform to the Top
Ladder Extensions using two
(2) 1/4”x 2 1/4” Hex Bolts(E),
six (6) Nylon Washers and two
(2) 1/4” Nylock Nuts to secure.
Next, attach the bottom of
the Under Support Gussets to
the outside of Ladder Section
A using two (2) 1/4”x 2 1/4”
Hex Bolts(E), four (4) Nylon
Washers and two (2) 1/4”
Nylock Nuts. (Fig.4)
SEAT ASSEMBLY
Hex Bolt (A) and one (1) 1/4” Nylock
Nut. (Fig. 4A) NOTE: The Seat
NOTE: Use an Allen Wrench to tighten the Seat
Tension Bolt as needed. (Fig. 4A)
Tension Bolt must be threaded
completely into the Seat Bar for
proper assembly. Then slip the
backrest of the Seat Assembly
over
the Backrest Supports and secure
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
Ladder Section A
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

STEP 7. Connect the Left and Right Shooting Rails using one (1) (A) 1/4" x 1 1/4" Hex
Bolt and one (1) (N) 1/4" Wiz Nut. Attach the assembled Shooting Rail to the outside
of the Armrests using two (2) (I) 1/4" x 2 1/2"Carriage Bolts (already installed) two (2)
(2) (K) 3/8" Nylon Spacers and two (2) (L) 1/4" Delta Nuts. Next attach Shooting Rail
Foam and Armrest Foams to Shooting Rail and Armrests. Install Armrest Covers and
Shooting Rail Cover by laying them over foam and securing Velcro. Install Accessory
Hooks and Drink Holder in desired locations. (Fig. 5)
FIGURE 5
WARNING! Shooting rail is provided for comfort and should be used as a shooting rail only. The shooting rail is
not designed to carry the full weight of the user. Never place more than fifteen (15) lbs of force on the shooting rail.
Failure to follow these instructions may result in serious injury or death!
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
STEP 6. Attach the Left
and Right Backrest
Supports to the Rear Foot
Platform using three (3)
1/4” 1/4” x 2” Hex Bolt (D),
six (6) Nylon Washers and
three (3) 1/4”
Nylock Nut.
(Fig. 5)
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

[G]
[G]
[J]
[J]
FIGURE 6
STEP 8. Attach Jaws to rear frame
support installing one Jaw on top
of Rear Frame Support and one Jaw
on bottom of Rear Frame Support (as
shown in Fig. 6) using two (2) (G)
5/16" x 3 1/2" Hex Bolts, six (6) Nylon
Washers, and two (2) 5/16" Nylock
Nuts. Note: one of the Nylon Washers
go between the Jaw and the Rear
Frame Support. Next attach the two (2)
(J) 1/4" x 4 1/4" Eye Bolts to Rear
Frame Support, one (1) (J) Eye Bolt,
two (2) Nylon Washers (on top & bottom
of Eye Bolt) and one (1) 1/4" Nylock Nut
on top matching top Jaw and one (1) (J)
Eye Bolt, two (2) Nylon Washers (one
top & bottom of Eye Bolt) and one (1)
1/4" Nylock Nut on bottom matching
bottom Jaw (Fig. 6)
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

[J]
[J]
FIGURE 7
STEP 9. String one (1) Jaw Tightening Cable with eyelet bolt loop end first thru
(J) 1/4"x4 1/4" Eye Bolt, attach eyelet bolt end of cable to top Jaw using two
(2) Nylon Washers and one (1) 5/16" Nylock Nut and repeat for bottom Jaw
using second cable and two (2) Nylon Washers and one (1) 5/16" Nylock
Nut. (Fig. 7)
STEP 10. Securely tighten every nut and bolt at this time.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

FIELD INSTALLATION
-THE GENERAL XT -
WARNING! DO NOT attempt to install
this product on a tree that is not straight,
healthy, and devoid of dead branches,
limbs, vines, or anything that might
interfere with the installation. DO NOT
attempt to install this treestand on a
tree that is leaning, diseased, crooked,
has loose bark, or does not meet the
minimum installation diameter of nine (9)
inches (23 cm) at treestand height (i.e.
seating platform height) or exceeds the
maximum installation diameter of twenty
(20) inches (51 cm) at treestand height
(i.e. seating platform height).
Failure to follow these instructions may
result in injury or death!
FIGURE 8
FIGURE 9
Install the snap pins from the outside in.
STEP 1. Select a straight, healthy tree; one
devoid of dead branches and loose bark.
DO NOT attempt to install this product on a
tree that is not healthy.
STEP 2. Assemble ladder sections to the
main section. Each ladder section has
slight design differences and need to be
assembled in the proper order for correct
installation. The ladder sections are labeled
ladder section A, two ladder sections B,
ladder section C, and ladder section D.
(Fig. 8) After assembling the ladder, insert
snap pins in every joint, wrapping the
closure around back of tubing and securing
over end of pin.(Fig. 9)
Note: Ladder Sections B has two pieces.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

NOTE: Confirm the two (2) Jaws are in the fully open
position and the Jaw Tightening Cables are run properly
through the cable guide Eye Bolts.The extra cable length
should be lying on the ground next to the ladderstand,
and free from tangles or knots.
FIGURE 10
STEP 3. Confirm that the two (2) Jaw Tightening Cables are attached to each Jaw
and run through the cable guide eye bolts properly (Fig. 10).
STEP 4: Place the ladderstand flat on the ground in front of the tree with the
bottom Ladder Section (D) approximately three (3) feet away from the base of
the trunk (Fig. 11).
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

Three (3) inches
Three (3) Feet
NOTE: Repeat Step 6 if the treestand needs additional adjustment to make the
seating and standing platforms parallel with the ground.
STEP 5. With at least three (3) adults, gently raise the ladderstand to a vertical
position allowing the bark biters on the rear frame support to come in direct
contact with the tree.
STEP 6: Once elevated completely, carefully pull the base away from the tree
until the seating and standing platforms are parallel to the ground. (Fig. 11)
Bounce on the bottom ladder section rung to set the ladder into the ground at
least three (3) inches deep.
NOTE: The bottom ladder section is specially designed to
allow the bottom to drive into the ground. This is part of
normal installation. Check again to ensure seating and
standing platforms are parallel with the ground.
FIGURE 11
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

LADDER
SECTION C
LOWER BARK BITER
TREE BRACE
LOWER BARK BITER
LADDER BRACE
LOWER BARK BITER
LADDER BRACE
LOWER BARK BITER
TREE BRACE
LADDER
SECTION C
RATCHET
STRAPA
STEP 7. Attach the two (2) Lower Bark Biter Ladder Braces to
the Ladder Section (Ladder Section C) using two (2) 1/4" x 1
3/4" Hex Bolts [C] and two (2) 1/4"Wing Nuts [O] (Fig. 12) on
the dedicated bracket mounting location. NOTE: This is on the
second ladder section up from the ground.
FIGURE 12
Next, slide the two (2) lower bark biter tree braces into the
two (2) lower bark biter ladder braces. Adjust the length so
the bark biter teeth are hitting the tree evenly and install the
snap pins to secure (Fig. 11). Then, attach the ratchet strap
to the lower bark biter. This ratchet strap will be labeled
(Ratchet Strap A). Ratchets are attached to the dedicated
contact points on each lower bark biter. (Fig. 13) Carefully
tighten the ratchet strap securely.
FIGURE 13
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
C
C

LADDER
SECTION C
BRACE
NOTE: While doing Step 8 you will be able to visibly see
the Jaws moving to the point the Jaw bark biters touch
the tree. (Fig 14).
NOTE: Make sure the
Jaws contact the tree
evenly and are not
obstructed by knots,
branches, etc.
19
FIGURE 15
FIGURE 14
STEP 8b. Criss-cross the
cables behind the tree trunk
pulling snug. (Fig. 17) Then
run each Jaw Tightening Cable
through the eyelets that are
welded to the Lower Bark Biter
Ladder Braces. (Fig. 15)
JAW
REAR FRANE
SUPPORT
JAW
TREE TRUNK
STEP 8a. When the Lower
Bark Biters are secured
using the Ratchet Strap
(Ratchet Strap A) and
the lower bark biter is
assembled properly
(Fig. 13), grab the Jaw
Tightening Cables.
Holding one (1) cable in
each hand, stand behind
the tree and pull down
on each cable.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

STEP 1. Thread strap through slot in the
center of the ratchet reel. (see
fig. 1) Remove slack from strap by pulling
loose end as tightly as possible.
(see fig. 2)
STEP 2. Then ratchet handle back and forth
to tighten straps, a minimum
of two (2) wraps around the ratchet reel is
required. (see fig. 3)
STEP 3. After strap is tight, close handle to
the lock position.
STEP 4. To remove tension, pull spring loaded
retaining lock and open
ratchet completely, then manually pull strap
to loosen. (see fig. 4)
2X Min.
FIGURE 1 FIGURE 2
FIGURE 3 FIGURE 4
VITAL RATCHET INSTRUCTIONS
STEP 9. Once the Jaw Tigh-
tening Cables are crisscross-
ed around the back of the
tree and run through the eye-
lets on the Lower Bark Biter
Ladder pieces, then attach
the two (2) Jaw Tightening
Cables to the two (2) cara-
biners on Ratchet Strap B
assembly (Fig. 15). Next,
attach the S-hook on the
opposite end of the ratchet
strap to the dedicated loca-
tion on the bottom ladder
section (Fig. 16). Carefully
tighten the Ratchet Strap
(Ratchet Strap B) until stand
is secure.
NOTE: Your lower bark biters should be firmly gripping the tree at this time, and the
Jaws should be firmly gripping the tree. Shake the bottom ladder section of your
ladderstand to confirm the treestand is solid and connected to the tree firmly. Make
sure all straps are tight before each use.
FIGURE 16
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.