BOLTPOWER N02 User manual

EN
DANGER.
Prior to use, please read and understand product Safety information. Failure to
follow the instructions may result in ELECTRICAL SHOCK, EXPLOSION, or FIRE,
which may result in serious INJURY, DEATH, DAMAGE to device or PROPERTY!
DO NOT discard this INFORMATION!
What’s in the BOX
- N02 Lithium Jump Starter (Built-in Anti-reverse Protection)
- 12V/1A portable car charger (DC 3.5*1.35mn, cable length 100cm)
- jumper clamps
- 16.8V cigarette lighter car battery charger (for charging a car battery with N02)
(DC 5.5*2.1mm, cable length 230mm)
- Micro USB cable
- 12V/1A wall charger (DC 3.5*1.35mm, cable length 100cm)
- User guide & information guide and Warranty
N02 Introduction
The N02 is an ultra-compact and portable Lithium-Polymer used jump starter for
cars, motorcycles, boats, RVs, lawn mowers, ATVs, tractors, trucks and more. It’s
extremely safe for anyone to use. The N02 can instantly jump start most
single-battery devices, up to 20 times with a single charge. The N02 is also
equipped with a USB power bank function and LED flashlight, making it the
ultimate emergency tool.
Before Started
The N02 come partially charged and needs to be fully charged before use.
Carefully read and understand the vehicle owner’s manual on precautions
and recommended methods for jump-starting the vehicle. Make sure to
determine the voltage and chemistry of the battery by referring to your battery
owner’s manual prior to using this product. The N02 is for jump starting
12-volt lead-acid batteries only.
-1-

Connecting to the Battery
Verify that you have a 12-volt lead-acid battery before connecting to the battery.
The N02 is not suitable for any other type of battery. Identify the correct polarity
of the battery terminals for your vehicle. The positive battery terminal is typically
marked by three letters or symbol {POS, P, +}. The negative battery
terminal is typically marked by these letters or symbol {NEG, N, -} Do not make
any connections to the fuel lines, carburetor, or thin sheet metal parts. The below
instructions are for a negative ground system {most common}. If your vehicle is
a positive ground system {very uncommon}, follow the instructions below in
reverse order.
1} Connect the positive {red} battery clamp to the positive { POS, P, +} battery
terminal.
2} Connect the negative {black} battery clamp to the negative {NEG, N, -} battery
terminal or vehicle chassis.
3} When disconnecting in the reverse sequence, removing the negative first or
{positive first for positive ground systems}
Jump Starting Steps
1} Verify the voltage and chemistry of the battery.
2} Make sure all of the vehicle’s power loads {headlights, air conditioning, radio,
etc.} are turned off before attempting to jump start the vehicle.
3} Connect the EC5 connector to the N02. The boost LED will flash red and
green, the N02 go into standby mode
4} Confirm the battery clamps are connected to the correct polarity battery
terminals. Press the BOOST Button, LED light will turn into a solid green
light, the N02 is ready to jump start your vehicle.
5} If the battery clamps are connected correctly, but the boost LED is still
flashing red and green, press the BOOST button for 3 seconds, then
the Boost LED will turn into solid green, the N02 is ready to jump start your
vehicle.
-2-

6} Try starting the vehicle, most vehicles will immediately start. Some
vehicles may require the N02 to be connected for up to 30 seconds before
starting. If the vehicle does not start right away, wait 20-30 seconds and try
again. Do not attempt more than five (5) consecutive jump starts within a fifteen
(15) minute period. Allow the N02 to rest for fifteen (15) minutes before
attempting to jump start the vehicle again.
7} Once you have started your vehicle, disconnect the battery clamps, and
remove the N02.
Low voltage batteries & manual override
The N02 is designed to jump start 12-volt lead-acid batteries down to 2-volts. If
your battery is below 2-volts, the boost LED will flash in red. This is an indication
that the N02 can not detect a battery. If you need to jump start a battery 2-volts
there is a Manual Override Feature, which allows you to force “on the jump start
function.
Caution on Manual Override Mode
Use this mode with extreme care. This mode is for 12-volt lead-acid batteries
only. Both the built-in anti-reverse protection and reverse polarity protection
features are disabled. Pay very close attention to the polarity of the battery
before using this mode. Do not allow the positive and negative battery clamps to
touch or connect to each other as the product will generate sparks. This mode
uses very high current {up to 1200 AMPS} that can cause sparks and high heat
if not used properly. If you are unsure about using this mode, do not attempt
and seek professional help.
-3-
CAUTION!

1. Internal Battery Level.
Indicates the power percentage of the internal battery LCD screen will display
“USB Out, if no load, it will turn off for 30s
2. Power Button
Push and hold to turn unit “On” & “Off”
3. DC Output.
Press Power button, connect to the cigar lighter to the charge the car battery
N02 user Interface
-4-
Before using the manual override feature, Make sure the battery clamps are
connected to the correct polarity battery terminals and the clamp connect is
connected to the N02. To use the manual override feature, press and hold
the BOOST button for {3} seconds The Green Boost LED will be green indicating
you have successfully entered into Manual Override and it is ready to jump start
your vehicle. If connected in reverse polarity the RED error LED will illuminate
and the unit will not operate.
Power Button/Light Mode Button
Internal Battery Level

-5-
Understanding Error Conditions
The N02 shall display and error condition when you reverse polarity condition is
present, a battery below two (2) volts, or internal battery overheating. When one
of these error conditions are present, the following will happen
Error Reason/Solution
Reverse polarity/
Reverse the battery
Connections
Error LED
Solid Red
Boost LED
Boost Button DC Output
Error LED
Blinking Red
w/cables connected
Properly
Boost Light does
not come on
w/cables connected
properly
The internal battery
is too hot/bring the unit
into cooler enviroment
Connected battery is below
2-volts/ remove all loads,
and try again, or use
manual override mode

-6-
USB Charging Rating
15V/1A
3.5hr
Estimated
Time
5V/2A
6hr
Charging the N02
Connect the N02 using the included USB charge cable to the USB in port and the
USB car charger. It can be recharged from any USB powered port like an AC
adapter, Car charger. laptop and more. The USB In port is rated at 5V/2.1 Amps
and 15V/V1 amps to ensure safe and ensure safe and efficient charging of the
internal lithium battery due to FCC regulations, we recommend not to charge and
discharge the unit at the same time.
N02 charging times
The time to recharge the N02 will differ based on the discharge level
and the power source used. Actual results may vary due to battery
conditions.
Charging your USB Devices
You can charge virtually any USB devices. Connect the included USB charge
cable to the USB Out port and connect to your USB device. Any 5V USB (White)
devices, Quick Charge 3.0 USB (Blue) 3.6V˜12V devices.
LED Flashlight
The N02 has an integrated ultra-bright LED flashlight. It has three (3)
light modes: Flashlight, SOS, Strobe
The N02 has a built in energy saving feature that will automatically turn the
unit off after one (1) minute. To continue using simply power on the unit
again.
Technical Specifications
Internal Battery: Lithium Polymer
Peak Current Rating 1200A
Operating Temperature -20ºC to +50ºC
-4.0 F to + 122 F
-20ºC to +50ºC
-4.0 F to + 122 F (Avg. Temp)
Capacity: 44.4Wh
Input 5V/2A 15V/1A
USB 1 (output) 5V, 2.1A
USB 2 (output) QC 3.0
DC (output) 12V/8A
Dimensions { L x W x H} 7.1x3.2x1.4 Inches
Weight
Cold Craking Amps
2.4 Pounds
600A
Storage Temperature
-7-

Technical Specifications
Internal Battery: Lithium Polymer
Peak Current Rating 1200A
Operating Temperature -20ºC to +50ºC
-4.0 F to + 122 F
-20ºC to +50ºC
-4.0 F to + 122 F (Avg. Temp)
Capacity: 44.4Wh
Input 5V/2A 15V/1A
USB 1 (output) 5V, 2.1A
USB 2 (output) QC 3.0
DC (output) 12V/8A
Dimensions { L x W x H} 7.1x3.2x1.4 Inches
Weight
Cold Craking Amps
2.4 Pounds
600A
Storage Temperature
-7-