Könner & Söhnen KS JSP-1200 User manual

Owner’s Manual
Please, read this manual
carefully before use!
Jump starter with air compressor
KS JSP-1200
USA

INTRODUCTION
Thank you for your purchase of Könner & Söhnen®products. This manual contains a brief description of
safety, use and debugging. More information can be found on the ocial manufacturer’s website in the
support section: konner-sohnen.com/manuals
You can also go to the support section and download the manual by scanning the QR code, or on the
website of the ocial importer of Könner & Söhnen®products: www.konner-sohnen.com/en-us
Manufacturer reserves the right to make alterations into the generators, which may not be reected in this
manual. Pictures and photos of the product may vary from its actual appearance. At the end of this manual,
You may nd contact information which you are free to use in case of any issues occurrence.
All data, specied in this operation manual is the most up to date for the moment of its publishing. The current
list of service centers you can nd at the website of ocial importer: www.konner-sohnen.com/en-us
Jump starter has following functions
Please, read this manualPlease, read this manual
carefully before use!carefully before use!
Failure to follow the recommendations marked with this
sign may lead to serious injury of the operator or third
parties.
Useful information while operating the machine.
ATTENTION – DANGER!
IMPORTANT!
JUMP STARTER WITH AIR COMPRESSOR 1
MAIN OVERVIEW 2
Manufacturer reserves the right to make changes and/or
improvements in design, components set and technical
attributes without notice and without incurring obliga-
tion. The pictures in this manual are schematical and may
not match the parameters of original product.
IMPORTANT!
konner-sohnen.com |1
Cordless air compressorJump starter Device charging function Flashlight function
Jump starter KS JSP-1200 can instantly start 12V vehicles up to 2.1 gal. (6L) gasoline or
1 gal. (4L) diesel engines. To avoid safety risks, please do not jump start the car with
an unsuitable low capacity.

HOW TO USE LED EMERGENCY LIGHTINGHOW TO USE LED EMERGENCY LIGHTING
Press and hold the key for 3 seconds to turn on the ashlight, then
the light button function changes from solid light to ashing, SOS
distress signal light. Press and hold again for three seconds to turn
o the ashlight.
FUNCTIONS/OPERATION 4
1. Air hose connector
2. Air compressor switch
3. Pressure down
4. Mode selection
5. Pressure up
6. Intelligent digital display
7. DC connector/Output for connecting the terminals
of the jump starter
8. Power switch
9. Charging port
10. USB outputs
THE PACKAGE INCLUDES:THE PACKAGE INCLUDES:
• Jump starter
• Packaging
• Operating instruction
55
33
1199
1010
77
66
88
22
44
TECHNICAL SPECIFICATION 3
Model KS JSP-1200 parameters Value
Battery 14000 mAh
Max. pneumatic pressure 150 psi
USB output 2x5V/2А
USB input 5V/2А
Rated starting current 600 A
Peak current 1200 A
Charging time 4-5 hours
Net dimensions (LхWхH) 7.9’’*5.1’’*2’’
Net weight 2.2 lbs
Operating temperature (-4 °F) – (+140 °F)
1212
1111
1313
1414
11. Smart clamp
12. USB charging cable
13. Nozzle adapters+Accessories storage bag
14. Air hose
konner-sohnen.com |2

The device is suitable only for 12V batteries!
WARNING!
HOW TO START A CAR WITH A FLAT BATTERY:HOW TO START A CAR WITH A FLAT BATTERY:
When starting the car, please conrm that the power of the product is more than 20%.
STEP 2:STEP 2: Сonnect the battery clamp to the
positive and negative poles of the car battery
(Red for the positive terminal and black for the
negative terminal).
STEPSTEP 1:1: Open the silicone stopper of the
product and insert the battery clamp into
the corresponding hole of the product.
STEPSTEP 3:3: Start the engine. Do not cycle the jump
starter for more than 3 seconds, pause for 1 minute
between jump start attempts. This is necessary to
let the jump starter battery cool down.
STEPSTEP 4:4: The plug is withdrawn from the
jump starter rst, and then the battery clips
are removed from the positive and negative
terminals.
When the connection is successful, the indicator lights up green.
The red light indicates that the supply voltage is too low or that the positive and negative electrode terminals
have been swapped.
DEVICE CHARGING FUNCTION:DEVICE CHARGING FUNCTION:
Plug the USB charging cable into the product 5V/2A USB interface. Plug the other end of the charging cable
into the corresponding interface of the mobile phone or digital product. After connecting the cable, press
the SWITCH key (device switch) to start power supply.
The device is protected against overheating. If the device gets overheated, the red indicator light will be on
continuously, and the buzzer will emit 2 beeps per second. Once the fault has been rectied, the buzzer will
return to normal status. Overtemperature protection is is triggered at 176 °F.
The device features protection against overcurrent. If the protection is triggered, the device will automati-
cally shut down, the protection indicator will light up, and the buzzer will emit 4 beeps per second. After the
fault has been rectied, the indicator will immediately return to normal status.
It is recommended that you use an AC adapter with an output of at
least 5V/1A or preferably 5V/2A for charging. It can be a smartphone
or tablet charger.
TYPE-C
Insert the matching adapter and charger plug into the USB Type-C input port of the product.
konner-sohnen.com |3

1. Read the operating instructions carefully before using the device.
2. The device must never be used as a substitute for a car battery.
3. Keep children and animals away from the working area of the device.
4. Only use the jump starter for 12 V batteries.
5. Keep the clips and their connection points clean and tidy. Never connect the clips together.
6. Avoid using the device near explosive substances, flammable gases, or in dusty environments.
7. Avoid overheating the device, smoking near the device, and exposing the device to extreme moisture;
keep the device away from open flames and never immerse it in water.
8. The device must not be stored at temperatures exceeding 140 °F.
9. After successfully jump-starting the vehicle, disconnect the jump starter from the battery within
30 seconds to prevent equipment damage.
10. Do not use the jump starter cable to charge other devices.
11. Keep it supervised while charging.
12. Using the device at current and voltage ranges other than those specified on the device nameplate may
cause charging and discharging problems and deterioration of battery capacity and performance. This
is also dangerous and may cause the device to malfunction.
13. When the battery is stored for more than three months, the product needs to be charged to ensure the
normal performance of the product.
14. Never do anything that may cause mechanical damage to the device.
15. Do not disassemble or transform the product without authorization.
16. Ifthedevicecasingisbulged,leaking,orgivingoffanunpleasantodor,stopusingthedeviceimmediately.
17. If you notice battery acid leaking from the battery, do not touch it with bare hands. If battery acid
contacts the skin or eyes, rinse immediately with plenty of running cold water and soap. Flush eyes for
at least 10 minutes. Seek medical advice if necessary.
18. The device features a lithium rechargeable battery that must be disposed of under the applicable laws
in your country.
19. Please connect the starting cable correctly according to the manual.
AIR COMPRESSOR FUNCTIONAIR COMPRESSOR FUNCTION
Connect one end of the
ination line to the air hole
Connect one end of the
ination cable to the tire
Then press the M key to select the mode
(cars, motorcycles, bicycles, sports
equipment).
Turn on the ination switch to inate and
automatically stops when the desired
parameters are reached
After connecting the wires,
press the key to start the
machine
WARNING 5
konner-sohnen.com |4

20. Never attempt to jump-start the vehicle in continuous mode! With standard power, the start cycle
should take no more than 3 seconds, and the interval between cycles should be at least 1 minute. Do
not exceed 3 consecutive start attempts.
21. After starting the car with the starting power, the temperature of the starting power supply itself will rise,
please do not charge the starting power at this time, at least 8-10 minutes before charging.
22. Only use the jump starter cable supplied with the jump starter.
23. Do not charge the device immediately after jump-starting the vehicle’s battery.
24. Never use the device to start the vehicle’s battery and charge the device’s internal battery simultaneously.
konner-sohnen.com |5

CONTACTS
The United States:The United States:
KS Energy Solutions, Inc.
Balcones Drive STE 100 Austin,
TX 78731, USA
Authorized Warranty ServiceAuthorized Warranty Service
[email protected]
www.konner-sohnen.com/us