BOND MANUFACTURING Y96598A User manual

DO NOT RETURN TO RETAILER
IF YOU HAVE ANY
QUESTIONS OR CONCERNS
PLEASE CALL
BOND MANUFACTURING
TOLLFREE AT
1-866-771-BOND(2663)
MONDAY –FRIDAY 8AM TO 4:30 PM PST
OR EMAIL TO
[e-mail]
OR VISIT OUR WEBSITE ON
www.bondmfg.com
STOP

Assembly Instructions
Item#: Y96598A
* * WARNING * *
Read these instructions carefully and keep the fountain power off until the following
assembly process is strictly completed.
Notes:
⚫Choose an appropriate location for the fountain.
⚫Excessive weight or pressure on any of the fountain sections may cause it to fall. Keep pets, children,
or anyone f rom sitting, leaning, or climbing on any of the f ountain components.
⚫While fountain is designed to operate as splash free as possible, some water splashing out of the
fountain is inevitable. Place the fountain in a location where any splashing will not cause dam age.
⚫The National Electric Code requires that a ground fault circuit interrupter (GFCI) be used in the
branch circuit supplying fountain pump and other pond equipment. Seek your electrical supplies
dealer f or this device.
⚫Always keep the fountain working with sufficient water and clean of debris and dirt to ensure proper
functioning of the pump.
⚫If necessary, clean the f ountain with a sof t cloth and change the water frequently. Due to water
evaporation, you may see a buildup of white residue on the fountain surface from mineral content
in the water supply. To prevent such buildup, regularly clean the f ountain with soap and water, do
not use any abrasive, which may damage the applied finish.
⚫Use of water clarifier, or algaecide of any kind will damage the paint on the fountain and
will not be covered under the manufactures warranty.
⚫See the pump instructions for pump safety, maintenance, and warranty information.
⚫Keep this manual f or future reference.
Installation & Assembly
⚫Place the fountain on a level surface, away from areas where it is likely to get clogged with leaves
and make sure that the cable will reach the socket.
⚫Take out all the packaged parts from the carton
⚫Follow steps to assemble as illustrated below
Step (1). Pull out the f lexible hose from the back door- ＂location ①＂of the fountain,
then connect it to pump outlet, showed as ②
Step (2). Pull out the cable line of the light from the back door ＂location ①＂of the fountain,
then connect the connector of LED light to the adaptor, showed as ③
Step (3). Closed up the back cover to the fountain as showed ④in Figure ‘1’.
Figure’2’
Fill the reservoir with clean water caref ully. Always make sure the water can submerge the pump
completely to work properly and prevent the pump damage.
Plug the pump and adaptor then switch on, the water will start to flow in minutes, and lights will be
shining instantly.
⚫Adjust the pump flow rate to achieve the desired effect and to minimize any splashing, showed as
(F). Splashing can occur if the f low rate is too high or the reservoir is too full. The flow rate can be
increased or decreased by moving the f low rate control slider on the pump body. Moving the s lider
towards ‘+/ Max.’ will increase the flow rate and moving it towards ‘-/Min’ will decrease it.
On some type of pumps, flow regulator may be turned clockwise or counterclockwise to adjust.
1

2

Troubleshooting
- - TURN OFF THE POWER BEFORE YOU CHECK THE FOLLOWING - -
If pump does not run, or lights are not on --
(1) Check the circuit breaker, try another outlet.
(2) Check the water level in the fountain. Running the pump without suff icient water can damage the
pump.
(3) Check the setting of the flow control on the pump and adjust the flow.
(4) Check the pump discharge and intake f or dirt and debris.
(5) Check the f ountain for kinks and obstructions.
(6) The pump might be “air locked”. Plug and unplug the pump several times to release the air inside the
pump.
(7) Check and reconnect the cord and try again.
IF YOU HAVE QUESTIONS OR CONCERNS
PLEASE CALL BOND TOLL FREE #
+1-866-771-BOND(2663) OR TO BETTER
EXPEDITE YOUR REQUEST FEEL FREE TO EMAIL US
Customer.service@bondmf g.com
OR LOG IN TO OUR WEBSITE UNDER CUSTOMER SERVICE SUPPORT
www.bondmfg.com
3