Campania International Juliet Fountain User manual

F
T
-
310
Juliet
Fountain
Revised
June26, 2017
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
Pump KitPartsList
PK140 pump (1)
#7 stopper(1)
Approx.9”length of1/2”BlackNon-Kinktubing (1)**
2”length of5/8”clearvinyltubing (1)**
2”length of1/2"PVCpipe (1)**
Wedges(2)
Hose clamps(2)*
*Hoseclampsmaybe used as flow restrictor
**Black non-kink tubing and clear vinyltubing havebeen preassembled
FOUNTAININFORMATION:
Thisfountain holdsapproximately3gallonsof water.
Thisfountain usesasmallfountain cover.
(FTNCOV-SM)
Norefill device orsubmersible lightsare suggested for
thisfountain
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
OEMPF140 - 140GPH Pump
6FTcord length

F
T
-
310
Juliet
Fountain
Revised
June26, 2017
Assemble your fountainon alevel surface capable ofholding aminimumof215
poundswithanapproximate1squarefootfootprint.
FT-310C(174 lbs)
27.25”Lx24.75”Wx37”H
FT-310B(3 lbs)
8.25”Wx2”H
FT-310A(3 lbs)
7.25”Wx3”H
1. Position thebasin(FT-310C) wherethefountainis
tobeinstalled, ensuring that it islevel.
2. Assemble thepumpkit
a. Connect thetubingtothepumpoutlet.
b. Place thestopper around thepumpcord
approximately6”fromthepump.
3. Feedthepumpcordthrough thehole and channel in
thebasin(FT-310C).
4. FIRMLYpressthestopper intothehole evenly.
a. Note: Using thehandle ofascrewdriver or
hammerworksbesttopress thestopper in
place.
5. Place thePumpHouseRing (FT-310B) insideofthe
basin, ensuring that it iscenteredand level.
6. Holding thewaterfeaturedisc(FT-310A) over the
basin, insertthePVCconnectedtothenon-kink
tubing intothePVCcoupling protruding fromthe
bottomofthedisc.
7. Carefullyplace water featureontothePumpHouse
Ring (FT-310B) ensuring that it iscenteredand
level.
8. Fill thefountainwithwater.