Bosch GV 630 S Setup guide

R
R
RE
E
EP
P
PA
A
AI
I
IR
R
R I
I
IN
N
NS
S
ST
T
TR
R
RU
U
UC
C
CT
T
TI
I
IO
O
ON
N
NS
S
S
GV630 N
1SAFETY .......................................................3 4.14 Level sensor with safety function ....................................25
4.15 Filter system ......................................................................26
2INSTALLATION ...........................................5 4.16 Spray system .....................................................................27
4.17 Rinsing and pumping system...........................................28
2.1 Aligning the appliance........................................................ 5
4.18 Door seal ............................................................................29
2.2 Electrical connection.......................................................... 5
4.19 Door spring ........................................................................30
2.3 Water connection................................................................ 5
4.20 Circulation pump (SICASYM) ...........................................31
3OPERATION................................................6
4.21 Water inlet without heat exchanger .................................33
3.1 Function............................................................................... 6 4.22 Water points.......................................................................34
3.2 Special funtions .................................................................. 8 4.23 Montage of the electronic module....................................35
3.3 General information on control ......................................... 9 5FUNCTIONS .............................................. 36
4COMPONENTS..........................................12
5.1 3 in 1 detergent detection function ..................................36
4.1 Actuator ............................................................................. 12 6REPAIR ..................................................... 37
4.2 Aqua sensor (optional)..................................................... 13
6.1 Diagnosis aids ...................................................................37
4.3 Aqua Stop valve ................................................................ 14
7FAULT DIAGNOSTICS.............................. 38
4.4 Worktop (optional) ............................................................ 16
4.5 Flow sensor....................................................................... 17
7.1 Controller / module with display ......................................38
4.6 NTC .................................................................................... 18
7.2 Draining ..............................................................................39
4.7 Regeneration / drainage valve ......................................... 18
7.3 Odour..................................................................................40
4.8 Optical low rinse-aid sensor (optional)........................... 19
7.4 Noises.................................................................................41
4.9 Hinge.................................................................................. 20
7.5 Rinsing result.....................................................................42
4.10 Dispenser........................................................................... 21
7.6 Drying result ......................................................................50
4.11 Instantaneous water heater.............................................. 22
7.7 Circulation pump ...............................................................51
4.12 Water softening system.................................................... 23
8TECHNICAL SPECIFICATIONS ................ 52
4.13 Detergent-solution pump ................................................. 24
202_58300000104305_ara_en_b – 02.11.a Seite 1 von 52

8.1 General technical specifications ..................................... 52
8.2 Consumption rates ........................................................... 52
202_58300000104305_ara_en_b – 02.11.a Seite 2 von 52

1 SAFETY
DANGER
Repairs may be carried out by a qualified electrician only!
The user may be put at risk and injured by improper repairs!
To prevent electric shocks, always comply with the following
instructions:
►
►
►
►
►
►
►
The protective conductor resistance must never exceed the
values specified in the standard! The protective conductor is
crucial for personal safety and appliance function.
When repairs are complete, conduct a test in accordance with
VDE 0701 or the corresponding national regulations!
When repairs are complete, perform a function and leak test.
If the appliance is faulty, the housing or frame may be live!
Electric shock may occur if live components are touched
inside the appliance!
Before commencing repairs, disconnect the appliance from
the power supply!
If tests have to be performed while the appliance is live,
always use a residual-current-operated circuit-breaker!
202_58300000104305_ara_en_b – 02.11.a Seite 3 von 52

Sharp edges: Wear protective gloves.
Electrostatic sensitive devices!
Please observe handling regulations.
WARNING
Comply with the following instructions:
If conducting the test in accordance with VDE 0701 via the connector,
the heater (instantaneous water heater) must be tested directly for
insulation faults due to all-pole disconnection (relays; pressure switch)
or the differential current must be measured on the appliance!
If replacing the dispensing device and the pump sump, beware of
sharp edges in the area of the stainless-steel modules.
Before commencing repairs, always disconnect the appliance from the
power supply! If tests have to be performed while the appliance is live,
always use a residual-current-operated circuit-breaker!
202_58300000104305_ara_en_b – 02.11.a Seite 4 von 53

2 INSTALLATION
2.1 Aligning the appliance
To ensure a perfect locking function and prevent leaks in the area of
the door, the appliance must be aligned precisely via the height-
adjustable feet. If the appliance is integrated, the middle rear height-
adjustable foot can be adjusted from the front.
Note: Built-under and built-in appliances.
Using the height-adjustable feet, raise the appliance until the housing
touches the worktop.
The installation instructions (drilling template) are required for
attaching the furniture front to integrated and fully integrated
appliances.
The tensile force of the door springs in integrated and fully integrated
appliances can be adjusted to the weight of the furniture door (See
Door spring point).
To prevent injury, a side cover 481271 can be fitted near the hinges of
end appliances which are built in or under or are free-standing.
2.2 Electrical connection
Connect the appliance to a correctly installed earthed socket only.
Comply with the specifications on the rating plate.
2.3 Water connection
If the appliance is connected to the drain with the standard hose
length, the max. permitted height from the floor is 90 cm. If the
drainage hose is extended, a max. height of 80 cm must not be
exceeded. The water connection (¾ inch) requires a conventional
water line with a water pressure of at least 0.5 bar (0.5 at.) (when the
tap is turned on, the water flow rate must be more than 8 l/min.). If the
water pressure is more than 10 bar (10 at.), a pressure reducing valve
must be installed.
The appliances can be connected to warm water up to 60 °C.
However, it is recommended to connect the appliance to cold water
(better drying and washing results).
Connection dimensions for all 60 cm dishwashers
a = 1.3 m
b = 1.6 m
c = 1.4 m (3.6 m with extension set)
d = 1.2 m (3.4 m with extension set)
e = 1.6 m (3.6 m with extension set)
f = 1.2 m (3.2 m with extension set)
202_58300000104305_ara_en_b – 02.11.a Seite 5 von 52