
11
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The symbol for the time-setting
option that is visible in the display is shown in brackets.
To call up the Utimer, rcooking time, pend time or 0
clock, press the 0button repeatedly until the brackets are
around the relevant symbol. The display shows the value for a
few seconds.
End time
You can change the time at which you wish your dish to be
ready. The oven starts automatically and finishes at the desired
time. You can, for example, put your dish in the cooking
compartment in the morning and set the cooking time so that it
is ready at lunch time.
Ensure that food is not left in the cooking compartment for too
long as it may spoil.
Example in the picture: it is 10:30 am, the cooking time is
45 minutes and the oven is required to finish cooking at
12:30 pm.
1. Adjust the function selector.
2. Set the temperature selector.
3. Press the 0button twice.
4. Use the @or Abutton to set the cooking time.
5. Press the 0button.
The brackets are around p. The time when the dish will be
ready is displayed.
6. Use the @or Abutton to set a later end time.
After a few seconds, the oven adopts the settings and switches
to standby position. The time at which the dish will be ready is
shown in the display and the psymbol is in brackets. The U
and 0symbols go out. When the oven starts, you can see the
cooking time counting down in the display and the rsymbol is
in brackets. The psymbol goes out.
The cooking time has elapsed
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the 0button. You can set a new cooking time
using the @or Abutton. Or press the 0button twice and turn
the function selector to the off position. The oven switches off.
Changing the end time
Use the @or Abutton to change the end time. After a few
seconds, the change is adopted. If the timer has been set, first
press the 0button twice. Do not change the end time if the
cooking time has already started to elapse. The cooking result
would no longer be correct.
Cancelling the end time
Use the Abutton to reset the end time to the current time. After
a few seconds, the change is adopted. The oven starts. If the
timer has been set, first press the 0button twice.
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The symbol for the time-setting
option that is visible in the display is shown in brackets.
To call up the Utimer, rcooking time, pend time or 0
clock, press the 0button repeatedly until the brackets are
around the relevant symbol. The display shows the value for a
few seconds.
Clock
After the appliance is connected or following a power cut, the
0symbol and four zeros flash in the display. Set the clock.
1. Press the 0button.
The clock in the display shows 12:00. The time symbols light
up and the brackets are around 0.
2. Use the @or Abutton to set the clock.
After a few seconds, the time that has been set is adopted.
Changing the clock
No other time-setting option should have been set.
1. Press the 0button four times.
The time symbols light up in the display and the brackets are
around 0.
2. Use the @or Abutton to change the clock.
After a few seconds, the time that has been set is adopted.
Hiding the clock
You can hide the clock. For more information, please refer to
the section Changing the basic settings.
Childproof lock
The oven has a childproof lock to prevent children from
switching it on by accident.
The oven will not respond to any settings.You can still set the
clock and the timer when the childproof lock is activated.
If the type of heating and temperature or grill setting are set, the
childproof lock interrupts the heater element.
Note: If a hob is connected, it will not be affected by the
childproof lock on the oven.
Activating the childproof lock
No cooking time or end time should be set.
Press and hold the Dbutton for approx. four seconds.
The Dsymbol appears in the display. The childproof lock is
activated.
Deactivating the childproof lock
Press and hold the Dbutton for approx. four seconds.
The Dsymbol goes out in the display. The childproof lock is
deactivated.