Bosch HBG8755.1 User manual

Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
Oven
HBG8755.1
[en] User manual and installation instructions

en Safety
2
Futher information and explanations are available
online:
Table of contents
USER MANUAL
1 Safety ....................................................................2
2 Preventing material damage ...............................5
3 Environmental protection and saving en-
ergy .......................................................................5
4 Familiarising yourself with your appliance ........6
5 Operating modes .................................................8
6 Accessories..........................................................9
7 Before using for the first time ...........................11
8 Basic operation ..................................................11
9 Rapid heating .....................................................12
10 Time-setting options..........................................13
11 AutoPilot.............................................................14
12 Childproof lock...................................................15
13 Sabbath mode ....................................................15
14 Basic settings.....................................................16
15 Cleaning and servicing......................................16
16 Cleaning function Pyrolytic self-cleaning ........18
17 Cleaning assistance...........................................19
18 Rails ....................................................................20
19 Appliance door...................................................20
20 Troubleshooting.................................................23
21 Disposal..............................................................25
22 Customer Service...............................................25
23 How it works.......................................................26
24 INSTALLATION INSTRUCTIONS .......................31
24.1 General installation instructions.......................31
1 Safety
Observe the following safety instructions.
1.1 General information
¡Read this instruction manual carefully.
¡Keep the instruction manual and the
product information safe for future refer-
ence or for the next owner.
¡Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
This appliance is designed only to be built
into kitchen units. Read the special installation
instructions.
Only a licensed professional may connect ap-
pliances without plugs. Damage caused by in-
correct connection is not covered under the
warranty.
Only use this appliance:
¡To prepare meals and drinks.
¡In private households and in enclosed
spaces in a domestic environment.
¡Up to an altitude of max. 4000m above
sea level.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Do not let children play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.

Safety en
3
1.4 Safe use
Always place accessories in the cooking com-
partment the right way round.
→"Accessories", Page9
WARNING‒Risk of fire!
Combustible objects that are left in the cook-
ing compartment may catch fire.
▶Never store combustible objects in the
cooking compartment.
▶If smoke is emitted, the appliance must be
switched off or the plug must be pulled out
and the door must be held closed in order
to stifle any flames.
Loose food remnants, fat and meat juices
may catch fire.
▶Before using the appliance, remove the
worst of the food residues and remnants
from the cooking compartment, heating ele-
ments and accessories.
Opening the appliance door creates a
draught. Greaseproof paper may come into
contact with the heating element and catch
fire.
▶Never place greaseproof paper loosely
over accessories when preheating the ap-
pliance and while cooking.
▶Always cut greaseproof paper to size and
use a plate or baking tin to hold it down.
WARNING‒Risk of burns!
The appliance and its parts that can be
touched become hot during use.
▶Caution should be exercised here in order
to avoid touching heating elements.
▶Young children under 8 years of age must
be kept away from the appliance.
Accessories and cookware get very hot.
▶Always use oven gloves to remove ac-
cessories or cookware from the cooking
compartment.
When the cooking compartment is hot, any al-
coholic vapours inside may catch fire.
▶Only use small quantities of drinks with a
high alcohol content in food.
▶Open the appliance door carefully.
WARNING‒Risk of scalding!
The accessible parts of the appliance become
hot during operation.
▶Never touch these hot parts.
▶Keep children at a safe distance.
Hot steam may escape when you open the
appliance door. Steam may not be visible, de-
pending on the temperature.
▶Open the appliance door carefully.
▶Keep children at a safe distance.
If there is water in the cooking compartment
when it is hot, this may create hot steam.
▶Never pour water into the cooking compart-
ment when the cooking compartment is
hot.
WARNING‒Risk of injury!
Scratched glass in the appliance door may
develop into a crack.
▶Do not use any harsh or abrasive cleaners
or sharp metal scrapers to clean the glass
on the oven door, as they may scratch the
surface.
The appliance and its parts that can be
touched may have sharp edges.
▶Take care when handling and cleaning
them.
▶If possible, wear protective gloves.
The hinges on the appliance door move when
the door is opened and closed, which could
trap your fingers.
▶Keep your hands away from the hinges.
Components inside the appliance door may
have sharp edges.
▶Wear protective gloves.
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
If the insulation of the power cord is dam-
aged, this is dangerous.
▶Never let the power cord come into contact
with hot appliance parts or heat sources.
▶Never let the power cord come into contact
with sharp points or edges.
▶Never kink, crush or modify the power
cord.
An ingress of moisture can cause an electric
shock.
▶Do not use steam- or high-pressure clean-
ers to clean the appliance.

en Safety
4
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶Call customer services. →Page25
WARNING‒Danger: Magnetism!
Permanent magnets are used in the control
panel or in the controls. These may affect
electronic implants, e.g. heart pacemakers or
insulin pumps.
▶Wearers of electronic implants must stay at
least 10 cm away from the control panel.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.
Children may breathe in or swallow small
parts, causing them to suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
1.5 Halogen bulb
WARNING‒Risk of burns!
The bulbs in the cooking compartment get
very hot. There is still a risk of burning for
some time after they have been switched off.
▶Do not touch the glass cover.
▶Avoid contact with your skin when cleaning.
WARNING‒Risk of electric shock!
When changing the bulb, the bulb socket con-
tacts are live.
▶Before replacing the bulb, ensure that the
appliance is switched off in order to pre-
vent a potential electric shock.
▶Also unplug the appliance from the mains
or switch off the circuit breaker in the fuse
box.
1.6 Cleaning function
WARNING‒Risk of fire!
Loose food remnants, fat and meat juices
may catch fire when the cleaning function is in
progress.
▶Before starting the cleaning function, al-
ways remove the worst of the food residues
and remnants from the cooking compart-
ment and accessories.
The outside of the appliance gets very hot
when the cleaning function is in progress.
▶Never hang combustible objects, e.g. tea
towels, on the door handle.
▶Leave the front of the appliance clear.
▶Keep children at a safe distance.
If the door seal is damaged, a large amount
of heat is generated around the door.
▶Do not scrub or remove the seal.
▶Never operate the appliance if the seal is
damaged or missing.
WARNING‒Risk of serious harm to
health!
The appliance gets very hot when the clean-
ing function is in progress. The non-stick coat-
ing on baking trays and tins is destroyed and
noxious gases are released.
▶Never clean non-stick baking trays or bak-
ing tins using the cleaning function.
▶Only clean enamelled accessories at the
same time.
WARNING‒Risk of harm to health!
The cleaning function heats up the cooking
compartment to a very high temperature so
that food left over from roasting, grilling and
baking will burn off. This process releases va-
pours, which can irritate mucous membranes.
▶Keep the kitchen well ventilated while the
cleaning function is running.
▶Do not remain in the room for long periods.
▶Keep children and pets away.
WARNING‒Risk of burns!
The cooking compartment gets very hot when
the cleaning function is in progress.
▶Never open the appliance door.
▶Allow the appliance to cool down.
▶Keep children at a safe distance.
The outside of the appliance gets very hot
when the cleaning function is in progress.
▶Never touch the appliance door.
▶Allow the appliance to cool down.

Preventing material damage en
5
▶Keep children at a safe distance.
2 Preventing material damage
2.1 General
ATTENTION!
Objects on the cooking compartment floor at over
50°C will cause heat to build up. The baking and
roasting times will no longer be correct and the enamel
will be damaged.
▶Do not place any accessories, greaseproof paper or
foil of any kind on the cooking compartment floor.
▶Only place cookware on the cooking compartment
floor if a temperature above 50°C has been set.
When the cooking compartment is hot, any water in-
side it will create steam. The change in temperature
may cause damage.
▶Never pour water into the cooking compartment
when it is still hot.
▶Never place cookware containing water on the
cooking compartment floor.
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶Allow the cooking compartment to dry after use.
▶Do not keep moist food in the cooking compartment
for a long time with the door closed.
▶Do not store food in the cooking compartment.
Leaving the appliance to cool down with the door open
will damage the front of neighbouring kitchen units over
time.
▶Always allow the cooking compartment to cool
down with the door closed after cooking at high
temperatures.
▶Take care not to trap anything in the appliance
door.
▶Only leave the cooking compartment to dry with the
door open if a lot of moisture was produced during
operation.
Fruit juice dripping from the baking tray leaves stains
that cannot be removed.
▶When baking very juicy fruit flans, do not pack too
much on the baking tray.
▶If possible, use the deeper universal pan.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
If the seal is very dirty, the appliance door will no
longer close properly during operation. This may dam-
age the front of adjacent kitchen units.
▶Keep the seal clean at all times.
▶Never operate the appliance if the seal is damaged
or missing.
Sitting or placing objects on the appliance door may
damage it.
▶Do not place or hang objects on the appliance door.
▶Do not place cookware or accessories on the appli-
ance door.
With certain models, accessories may scratch the door
pane when closing the appliance door.
▶Always push accessories fully into the cooking com-
partment.
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶Sort the individual components by type and dispose
of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Only preheat the appliance if the recipe or the recom-
mended settings tell you to do so.
¡Not preheating the appliance can reduce the en-
ergy used by up to 20%.
Use dark-coloured, black-coated or enamelled baking
tins.
¡These types of baking tin absorb the heat particu-
larly well.
Open the appliance door as little as possible during
operation.
¡This maintains the temperature in the cooking com-
partment and eliminates the need for the appliance
to reheat.
When baking multiple dishes, do so in succession or
in parallel.
¡The cooking compartment is heated after baking
the first dish. This reduces the baking time for the
second cake.
If the cooking time is relatively long, you can switch
the appliance off 10minutes before the cooking time
ends.
¡There will be enough residual heat to finish cooking
the dish.
Remove any accessories that are not being used from
the cooking compartment.
¡Accessories that are not being used do not need to
be heated.
Allow frozen food to defrost before cooking.
¡This saves the energy that would otherwise be re-
quired to defrost it.

en Familiarising yourself with your appliance
6
Note:
The appliance requires:
¡A maximum of 1W when the appliance is in opera-
tion with the display switched on
¡A maximum of 0.5W when the appliance is in oper-
ation with the display switched off
4 Familiarising yourself with your appliance
4.1 Control panel
You can use the control panel to configure all functions
of your appliance and to obtain information about the
operating status.
Note:On certain models, specific details such as col-
our and shape may differ from those pictured.
1 12 23
4
1
Buttons
The buttons on the left- and right-hand side of
the control panel have a pressure point. Press-
ing a button will execute its function. On appli-
ances without a stainless steel front, the but-
tons are also touch-sensitive.
2
Touch fields
Touch fields are touch-sensitive surfaces. To
select a function, simply press lightly on the rel-
evant field.
3
Control ring
The control ring can be turned infinitely in either
direction. Press down lightly on the control ring
and move it in the direction you require.
4
Display
The display shows the current settings, options
or relevant information.
4.2 Buttons
Use the buttons on the left- and right-hand side of the control panel to switch your device or the operating mode on
and off.
Button Function Use
On/Off Switch the appliance on or off.
Start/Stop Short press: Start or pause operation.
Press and hold for approx. three seconds: Cancel operation.
4.3 Touch fields
Use the touch fields to select different functions dir-
ectly.
The touch fields on the outside of the control panel are
designed for general functions; the touch fields on the
inside of the control panel are for the cooking mode.
The touch field for the function that is currently selected
lights up red.
Touch field
on the out-
side
Function Use
Timer Select the timer.
Childproof lock Press and hold for approx. four seconds: Activate or deactivate the child-
proof lock.
Information Display additional information about a function or setting.
To call up the basic settings, press and hold this for ap-
prox.threeseconds when the appliance is switched off.
Pyrolytic self-cleaning Select the cleaning function operating mode.

Familiarising yourself with your appliance en
7
Touch field
on the in-
side
Function Use
4D hot air Directly select the "4D hot air" type of heating.
Top/bottom heating Select the "Top/bottom heating" type of heating directly.
Types of heating Select the operating mode types of heating.
Temperature Select the temperature in the cooking compartment.
AutoPilot Select the AutoPilot operating mode with cooking programmes.
Weight Select the weight for the operating mode.
Time-setting options Select the time-setting options.
Rapid heating Starts or cancels rapid heating for the cooking compartment.
4.4 Control ring
You can use the control ring to change the setting val-
ues that are shown in the display.
If you have reached the maximum value for setting val-
ues, such as the temperature, minimum or maximum
value, this value remains in the display. If required, use
the control ring to turn the value back again.
For lists, e.g. the types of heating, the first value starts
again after the last value.
4.5 Display
The display shows the current setting values on differ-
ent levels.
Value in the
foreground
The value in the foreground is high-
lighted in white. You can use the control
ring to change the value directly.
Once operation has started, the temper-
ature or level is displayed in the fore-
ground.
Value in the
background
Values in the background are displayed
in grey. To change the value using the
control ring, select the required function
in advance.
Enlarge-
ment
As long as you use the control ring to
change a value, only this value will be
displayed as enlarged.
Display ring
The display ring is located around the outside of the
display.
¡Position indicator
If you change a value, the display ring shows you
where you are in the selection list. The display ring
may be continuous or divided into segments de-
pending on the settings area and the length of the
selection list.
¡Progress indicator
During operation, the display ring displays the pro-
gress and turns red at second-long intervals.
As the cooking time counts down, one segment of
the display ring disappears every second.
Temperature display
The heating line and the residual heat indicator show
you the temperature in the cooking compartment.
Due to thermal inertia, the temperature that is displayed
may differ slightly from the actual temperature inside
the cooking compartment.
¡Heating line
Once operation has started, the white line below the
temperature turns red as the cooking compartment
heats up. When you are preheating the appliance,
the optimal time to place your food in the cooking
compartment is as soon as the entire line has
turned red.
With set levels such as grill settings, the heating line
turns red immediately.
¡Residual heat indicator
When the appliance is switched off, the display ring
shows the residual heat in the cooking compart-
ment. As the residual heat dissipates, the display
ring gets darker before eventually disappearing
completely.
4.6 Cooking compartment
The functions in the cooking compartment make your
appliance easier to use.
Shelf supports
The rails in the cooking compartment enable you to
place accessories at different heights.
→"Accessories", Page9
Your appliance has five shelf positions. The shelf posi-
tions are numbered from bottom to top.
The rails are equipped with pull-out rails on one or
more levels, depending on the appliance type.
You can remove the rails, e.g. for cleaning.
→"Rails", Page20

en Operating modes
8
Lighting
One or more oven lights illuminate the cooking com-
partment.
When you open the appliance door, the light in the
cooking compartment switches on. If the appliance
door remains open for longer than 15minutes, the light
switches off again.
For most operating modes, the lighting is switched on
during operation. The lighting switches off again when
the operation ends.
Cooling fan
The cooling fan switches on and off depending on the
appliance's temperature. The hot air escapes above
the door.
ATTENTION!
Do not cover the ventilation slot above the appliance
door. The appliance overheats.
▶Ensure that the ventilation slots are unobstructed.
To ensure that the appliance cools down more quickly
after operation, the cooling fan continues to run for a
certain period afterwards.
Appliance door
If you open the appliance door during operation, the
operation stops. When you close the appliance door,
the operation continues automatically.
5 Operating modes
This is where you can find an overview of your appli-
ance's operating modes and main functions.
Operating
mode
Use
Types of
heating
Select finely tuned types of heating for
the optimal preparation of your food.
→"Types of heating", Page8
Operating
mode
Use
AutoPilot Programmed, recommended settings
for various types of food.
→"AutoPilot", Page14
Cleaning Select the cleaning function for the
cooking compartment.
→"Cleaning function Pyrolytic self-clean-
ing", Page18
→"Cleaning assistance", Page19
5.1 Types of heating
To ensure that you always use the right type of heating
to cook your food, we explain the differences and ap-
plications below.
The symbols for each type of heating help you to re-
member them.
When you select a type of heating, the appliance sug-
gests a suitable temperature or setting. You can use
these values or change them within the specified
range.
For temperature settings above 275°C and grill set-
ting3, the appliance reduces the temperature to ap-
prox. 275°C or grill setting1 after approx. 40minutes.
Symbol Type of heating Temperature What it's used for and how it works
Possible additional options
4Dhot air 30–275°C Bake and roast on one or more levels.
The fan distributes the heat from the ring-shaped heating element
in the back wall evenly around the cooking compartment.
Top/bottom heating 30–300°C Traditionally bake or roast on one level. This type of heating is
ideal for cakes with moist toppings.
The heat is emitted evenly from above and below.
Hot air eco 30–275°C Cook selected dishes gently on one level without preheating.
The fan distributes the heat from the ring-shaped heating element
in the back wall evenly around the cooking compartment. The
food is cooked in phases using residual heat.
This type of heating is most effective between 125 and 275°C.
Always keep the appliance door closed when cooking.
This type of heating is used to determine the energy consump-
tion in air recirculation mode and the energy efficiency class.
Top/bottom heating
eco
30–300°C Gently cook selected dishes.
Heat is emitted from above and below.
This heating function is most effective between 150 and 250°C.
This type of heating is used to measure the energy consumption
in the conventional mode.

Accessories en
9
Symbol Type of heating Temperature What it's used for and how it works
Possible additional options
Circulated air grilling 30–300°C Roast poultry, whole fish or larger pieces of meat.
The grill element and the fan switch on and off alternately. The
fan circulates the hot air around the food.
Grill, large area Grill settings:
1 = low
2 = medium
3 = high
Grill flat items such as steak and sausages, or make toast. Grat-
inate food.
The entire area below the grill element becomes hot.
Grill, small area Grill settings:
1 = low
2 = medium
3 = high
Grill small quantities, such as steak, sausages or toast. Gratinate
small quantities of food.
The central area below the grill element becomes hot.
Pizza setting 30–275°C Cook pizza or dishes that require a lot of heat from below.
The bottom heating element and the ring-shaped heating ele-
ment in the back wall heat the cooking compartment.
Slow cooking 70–120°C Slowly and gently cook seared, tender pieces of meat in un-
covered cookware.
The heat is emitted evenly from above and below at a low tem-
perature.
Bottom heating 30–250°C Final baking or cooking food in a bain marie.
Heat is emitted from below.
Defrosting 30–60°C Gently defrost frozen food.
Keeping food warm 60–100°C Keep cooked food warm.
Plate warming 30–70°C Plate warming.
6 Accessories
Use original accessories. These have been made espe-
cially for your appliance.
Note:Accessories may become deformed if they get
hot. Deformation has no effect on function. As the ac-
cessory cools down, it will regain its original shape.
The accessories supplied may differ depending on the
appliance model.
Accessories Use
Wire rack ¡Cake tins
¡Ovenproof dishes
¡Cookware
¡Meat, e.g. roasting joints or steak
¡Frozen meals
Universal pan ¡Moist cakes
¡Baked items
¡Bread
¡Large roasts
¡Frozen meals
¡Catch dripping liquids, e.g. fat when
grilling food on the wire rack.
Baking tray ¡Tray bakes
¡Small baked items

en Accessories
10
6.1 Locking function
The locking function prevents the accessories from tilt-
ing when they are pulled out.
You can pull out the accessories approximately halfway
without them tipping. The accessories must be inserted
into the cooking compartment correctly for the tilt pro-
tection to work properly.
6.2 Sliding accessories into the cooking
compartment
Always slide the accessory into the cooking compart-
ment the right way round. This is the only way to en-
sure that accessories can be pulled out approximately
halfway without tipping.
1. Turn the accessories so that the notch ⁠ is at the
rear and is facing downwards.
2. Insert the accessory between the two guide rods for
a shelf position.
Wire rack Insert the wire rack with the open
side facing the appliance door and
the curved lip ⁠ facing downwards.
Baking tray
E.g. univer-
sal pan or
baking tray
Slide the tray in with the sloping
edge ⁠ towards the appliance door.
3. To place the accessory at shelf positions with pull-
out rails, pull out the pull-out rails.
Wire rack
or baking
tray
Position the accessory so that its
edge is behind the lug ⁠ on the pull-
out rail.
Note:The pull-out rails lock in place when they are
fully pulled out. Gently push the pull-out rails back
into the cooking compartment.
4. Push the accessory all the way in, making sure that
it does not touch the appliance door.
Note:Take any accessories that you will not be using
out of the cooking compartment while the appliance is
in operation.
Combining accessories
You can combine the wire rack with the universal pan
to catch any liquid that drips down.
1. Place the wire rack on the universal pan so that
both spacers ⁠ are on the rear edge of the univer-
sal pan.
2. Insert the universal pan between the two guide rods
for a shelf position. In so doing, the wire rack is on
top of the upper guide rod.
Wire rack
on univer-
sal pan
6.3 Other accessories
You can purchase other accessories from our after-
sales service, specialist retailers or online.
You will find a comprehensive range of products for
your appliance in our brochures and online:
www.bosch-home.com
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance.
You can find out which accessories are available for
your appliance in our online shop or from our after-
sales service.

Before using for the first time en
11
7 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
7.1 Initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you need to configure the settings before you can use
it. It may take a few seconds for the settings to appear
in the display.
1. Turn the control ring to change the setting as re-
quired.
Possible settings:
– Language
– Clock
2. Press ⁠ to confirm.
aThe next setting appears.
3. Work through the settings and make changes as re-
quired.
aAfter the last setting, a note appears in the display
confirming that the initial configuration is complete.
aThe time that is set appears on the display.
4. To check the appliance before heating for the first
time, open and close the appliance door once.
7.2 Cleaning the appliance before using it
for the first time
Clean the cooking compartment and accessories be-
fore using the appliance to prepare food for the first
time.
1. Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
the adhesive tape that is in or on the appliance.
2. Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3. Press ⁠ to switch the appliance on.
4. Apply the following settings:
Type of heating 4D hot air ⁠
Temperature Maximum
Cooking time 1hour
→"Basic operation", Page11
5. Press ⁠ to start.
‒Keep the kitchen ventilated while the appliance is
heating.
aOnce the time has elapsed, an audible signal
sounds and the display shows the time as zero.
6. Press ⁠ to switch the appliance off.
7. Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with
soapy water and a dish cloth.
8. Clean the accessories thoroughly using soapy water
and a dish cloth or soft brush.
8 Basic operation
8.1 Switching on the appliance
▶Press ⁠ to switch the appliance on.
aThe Bosch logo appears in the display. The types of
heating then appear.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
▶Press ⁠ to switch the appliance off.
aThe appliance switches off. Any functions currently
in progress are cancelled.
aThe time or residual heat indicator appears in the
display.
8.3 Starting operation
You must start each operation.
▶Press ⁠ to start.
aThe settings, the running time, the display ring and
the heating line appear in the display.
8.4 Pausing or cancelling operation
You can briefly pause operation and then continue. If
you cancel operation completely, the settings will be re-
set.
1. To pause operation briefly:
‒Briefly press ⁠.
‒To continue operation, press ⁠.
2. To cancel operation completely, press and hold ⁠
for approx. 3 seconds.
aOperation will stop and all the settings will be reset.
8.5 Setting the operating mode
Once you have switched on the appliance, it suggests
an operating mode, e.g. types of heating.
1. If you want to use a different operating mode to the
one suggested, press the relevant touch field.
aThe touch field lights up red.
→"Operating modes", Page8
2. To implement other settings, press the relevant
touch fields.
3. Use the control ring to change the values.
4. Press ⁠ to start.

en Rapid heating
12
8.6 Setting the type of heating and
temperature
Requirement:The operating mode "Types of
heating" ⁠ has been selected.
1. Use the control ring to set the required type of heat-
ing.
2. Press ⁠.
aThe temperature is highlighted in white.
3. Use the control ring to set the temperature.
4. Press ⁠ to start.
aThe appliance starts heating.
aThe target temperature, the time and how long the
appliance has already been in operation are shown
in the display.
5. When the food is ready, press ⁠ to switch the appli-
ance off.
Tip:The most suitable type of heating for your food
can be found in the description of the type of heating.
→"Types of heating", Page8
Note:You can also set a cooking time and end time on
the appliance.
→"Time-setting options", Page13
Changing the type of heating
When you change the type of heating, the other set-
tings will also be reset.
1. Press ⁠ to pause operation.
2. Press ⁠.
aThe first type of heating appears in the display with
the corresponding default temperature.
3. Use the control ring to change the type of heating.
Changing the temperature
Once operation has started, you can change the tem-
perature directly.
▶Use the control ring to change the temperature.
aThe temperature is applied immediately.
Directly selecting types of heating
You can select certain types of heating directly using a
touch field.
1. Press the touch field for the required type of heat-
ing.
Available types of heating with direct selection:
– 4D hot air ⁠
– Top/bottom heating ⁠
aThe temperature is highlighted in white.
2. Use the control ring to set the temperature.
3. Press ⁠ to start.
aThe appliance starts heating.
aThe target temperature, the time and how long the
appliance has already been in operation are shown
in the display.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance dis-
plays some information, e.g. to ask you to do/confirm
something or to issue a warning, automatically.
1. Press ⁠.
aIf available, information is displayed for a few
seconds.
2. Use the control ring to scroll through longer pas-
sages of text.
9 Rapid heating
To save time, you can shorten the preheating time for
set temperatures of 100°C and higher.
You can use rapid heating for the following types of
heating:
¡4D hot air ⁠
¡Top/bottom heating ⁠
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note:Do not set a cooking time until rapid heating has
come to an end.
1. Set a suitable type of heating and a temperature of
at least 100°C.
2. Press ⁠.
aThe symbol lights up red.
3. Press ⁠ to start.
aRapid heating starts.
aWhen rapid heating has come to an end, an audible
signal sounds. The red symbol goes out.
4. Place the food in the cooking compartment.
Cancelling rapid heating
▶Press ⁠.
aThe red symbol goes out.

Time-setting options en
13
10 Time-setting options
Your appliance has different time-setting options, with
which you can control its operation.
10.1 Overview of the time-setting options
You can set a cooking time and end time for the opera-
tion. The timer can be set independently of the appli-
ance when it is in operation.
Time-setting
option
Use
Timer ⁠ The timer can be set independently
of the appliance when it is in opera-
tion. It does not affect the appliance.
Cooking time
⁠
If you set a cooking time for the op-
eration, operation of the appliance
stops automatically once this time
has elapsed.
End ⁠ For the cooking time, you can set the
time at which operation ends. The
appliance starts up automatically so
that it finishes cooking at the re-
quired time.
10.2 Setting the timer
The timer runs independently of the appliance when it
is in operation. The timer can be set when the appli-
ance is switched on or off, up to 23 hours and 59
minutes. The timer has its own audible signal so that
you can tell whether it is the timer or a cooking time
which has elapsed.
1. Press ⁠.
aThe symbol lights up red.
2. Use the control ring to set the timer duration.
3. Press ⁠ to start the timer.
The timer starts automatically after a few seconds.
aThe timer counts down.
aWhen the appliance is switched off, you will still be
able to see the timer counting down in the display.
aWhen the appliance is switched on, the display
shows the settings for the current operation. To dis-
play the timer for a few seconds, press ⁠.
aAn audible signal sounds once the timer duration
has elapsed. The red symbol goes out.
4. Once the timer duration has elapsed:
‒To stop the signal early, press any touch field.
‒To set another timer, press ⁠ and use the control
ring to set the time.
Changing the timer
You can change the timer duration at any time.
1. Press ⁠.
2. Use the control ring to change the duration of the
timer.
3. Press ⁠ to confirm.
Cancelling the timer
You can cancel the timer duration at any time.
1. Press ⁠.
2. Use the control ring to reset the duration of the
timer to zero.
3. Press ⁠ to confirm.
aThe red symbol goes out.
10.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement:An operating mode and temperature or
setting have been set.
1. Press ⁠.
aThe symbol lights up red.
2. Use the control ring to set the cooking time.
Direction of rotation Default value
Left 10minutes
Right 30minutes
The cooking time can be set in one-minute incre-
ments up to one hour, and then in five-minute incre-
ments. The end time is calculated automatically.
3. Press ⁠ to start.
aThe appliance starts to heat and the cooking time
counts down.
aWhen the time has elapsed, a signal sounds. The
time shown in the display is zero.
4. When the cooking time has elapsed:
‒To stop the signal early, press any touch field.
‒To set another cooking time, press ⁠ and use
the control ring to set the time.
‒To continue without setting a cooking time, press
⁠ to start.
‒When the food is ready, press ⁠ to switch the
appliance off.
Changing the cooking time
You can change the cooking time at any time.
1. Press ⁠.
2. Use the control ring to change the cooking time.
3. Press ⁠ to confirm.
Cancelling the cooking time
You can cancel the cooking time at any time.
1. Press ⁠.
2. Use the control ring to reset the cooking time to
zero.
3. Press ⁠ to confirm.
‒To continue without setting a cooking time, press
⁠ to start.
10.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡In order to achieve a good cooking result, do not
delay the end time once the appliance is already in
operation.
¡Food will spoil if you leave it in the cooking com-
partment for too long.

en AutoPilot
14
Requirements
¡An operating mode and temperature or setting have
been set.
¡A cooking time is set.
1. Press ⁠ again.
2. Use the control ring to delay the end time.
3. Press ⁠ to start.
aThe display shows the start time. The appliance is in
standby mode.
aOnce the start time has been reached, the appli-
ance starts to heat up and the cooking time starts
counting down.
aWhen the time has elapsed, a signal sounds. The
time shown in the display is zero.
4. When the cooking time has elapsed:
‒To stop the signal early, press any touch field.
‒To set another cooking time, press ⁠ and use
the control ring to set the time.
‒To continue without setting a cooking time, press
⁠ to start.
‒When the food is ready, press ⁠ to switch the
appliance off.
Changing the end time
In order to achieve a good cooking result, only change
the set end time before operation starts and the cook-
ing time is counting down.
1. Press ⁠ to pause operation.
2. Press ⁠ twice.
3. Use the control ring to change the end time.
4. Press ⁠ to continue operation.
Cancelling the end time
You can delete the set end at any time.
1. Press ⁠ to pause operation.
2. Press ⁠ twice.
3. Use the control ring to reset the end time to zero.
4. Press ⁠ to continue operation.
aThe appliance starts to heat and the cooking time
counts down.
11 AutoPilot
The "AutoPilot" operating mode helps you to use your
appliance to prepare different dishes by selecting the
optimum settings automatically.
11.1 Cookware
The cooking result depends on the composition of the
meat and the size of cookware.
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300°C. Glass or
glass ceramic cookware is best. The joint should cover
approx. two thirds of the cookware base.
Cookware made from the following material is not
suitable:
¡Bright, shiny aluminium
¡Unglazed clay
¡Plastic or plastic handles
11.2 Settings for the dishes
To make the dishes perfectly, the appliance uses differ-
ent settings.
Note:The cooking result depends on the quality and
composition of the food. Use fresh and, ideally, chilled
food.
Information on the settings
Once you start a dish, the display shows relevant
information for this dish, e.g.:
¡Suitable shelf position
¡Suitable accessory or cookware
¡Added liquid
¡Time for turning or stirring
When this time is reached, a signal sounds.
Programmes
The ideal type of heating, temperature and cooking
time are preset for programmes.
In order to obtain an optimal cooking result, you must
also set the weight. Unless otherwise indicated, set the
total weight for your dish. You can set the weight only
in the intended range.
11.3 Overview of the dishes
You can see which individual dishes are available to
you here.
Dishes
¡Chicken, unstuffed
¡Turkey breast
¡Pork neck, without bones
¡Pot-roasted beef
¡Joint of veal, marbled
¡Boned leg of lamb, medium
¡Meat loaf made from fresh mince
¡Goulash
¡Beef roulades
¡Stew with vegetables
11.4 Adjusting the dish
Note:Once it has started, you can no longer change or
interrupt the dish and the settings.
Requirement:To start the operation, the cooking com-
partment must be cooled down.
1. Press ⁠.
2. Use the control ring to set the required dish.
3. Press ⁠.
4. Turn the control ring to set the weight of your dish.
The cooking time is calculated automatically.
‒For some dishes, you can also delay the end
time.
→"Setting the end time", Page13
5. Press ⁠ to start.
aThe appliance starts to heat and the cooking time
counts down. The heating line does not appear.
aOnce the dish is ready, a signal sounds. The appli-
ance stops heating.

Childproof lock en
15
6. When the cooking time has elapsed:
‒To stop the signal early, press any touch field.
‒For some dishes, you can continue cooking if ne-
cessary.
→"Adding extra cooking time", Page15
‒When the dish is ready, press ⁠ to switch the ap-
pliance off.
Adding extra cooking time
For some dishes, the appliance offers the option to add
extra cooking time once the cooking time has elapsed.
You can do this as often as required.
1. If you do not want to continue cooking, press ⁠ and
switch off the appliance using ⁠.
2. To continue cooking the dish, press ⁠.
aA cooking time appears in the display.
3. Use the control ring to change the cooking time, if
required.
4. Press ⁠ to start.
aThe appliance starts to heat and the cooking time
counts down.
aWhen the time has elapsed, a signal sounds. The
appliance stops heating. The notification to continue
cooking appears again.
5. When the cooking time has elapsed:
‒To stop the signal early, press any touch field.
‒If you want to continue cooking again, press ⁠.
‒When the dish is ready, press ⁠ and use ⁠ to
switch the appliance off.
12 Childproof lock
You can secure your appliance to prevent children
from accidentally switching it on or changing the set-
tings.
12.1 Activating and deactivating the
childproof lock
You can activate and deactivate the childproof lock re-
gardless of whether the appliance is switched on or off.
1. Press and hold ⁠ for approx. 4 seconds to activate
the childproof lock.
aA confirmation note appears on the display.
aThe control panel is locked. The appliance can only
be switched off using ⁠.
aWhen the appliance is on, ⁠ lights up. When the ap-
pliance is off, ⁠ does not light up.
2. Press and hold ⁠ for approx. 4 seconds to deactiv-
ate the childproof lock.
aA confirmation note appears on the display.
13 Sabbath mode
You can set a cooking time of up to 74hours using
Sabbath mode. You can use top/bottom heating to
keep food warm between 85°C and 140°C during
this time without having to switch the appliance on or
off.
13.1 Starting Sabbath mode
Notes
¡If you open the appliance door during operation, the
appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again.
¡Once it has started, you can no longer change or in-
terrupt Sabbath mode.
Requirement:Sabbath mode is activated in the basic
settings.
→"Basic settings", Page16
1. Use the control ring to set the ⁠ Sabbath mode
type of heating.
2. Press ⁠.
aThe temperature is highlighted in white.
3. Use the control ring to set the temperature.
4. Press ⁠.
aThe symbol lights up red.
5. Use the control ring to set the cooking time.
The end time cannot be delayed.
6. Press ⁠ to start the operation.
aThe appliance starts to heat and the time starts to
count down.
7. Once the cooking time has elapsed, an audible sig-
nal sounds. The cooking time is at zero. The appli-
ance stops heating up and responds again as usual
outside of Sabbath mode.
‒Press ⁠ to switch the appliance off.
The appliance automatically switches off after ap-
prox.10to 20 minutes.

en Basic settings
16
14 Basic settings
You can configure the appliance to meet your needs.
14.1 Overview of the basic settings
Here you can find an overview of the basic settings
and factory settings. The basic settings depend on the
features of your appliance.
Basic setting Selection
Language See selection on the appli-
ance.
Clock Clock in 24-hour format.
Audible signal Short duration (30 seconds)
Medium duration (1 minute)1
Long duration (5 minutes)
Button tone Switched on
Switched off (tone remains
for ⁠)1
Display brightness 5 settings
Clock display Off
Digital1
Lighting Off during operation
On during operation1
Childproof lock Button lock only1
Door lock and button lock
Operation after switch-
on
Main menu
Types of heating1
AutoPilot
Night-time dimming Switched off1
Switched on
Brand logo Display1
Do not display
Fan run-on time Recommended1
Minimum
Pull-out system Not retrofitted (if shelf sup-
ports and a single set of
pull-out rails are fitted)1
Retrofitted (if two or three
sets of pull-out rails are fit-
ted)
1Factory setting (may vary according to model)
Basic setting Selection
Sabbath mode Switched on
Switched off1
Factory setting Reset
Do not reset1
1Factory setting (may vary according to model)
14.2 Changing the basic settings
Requirement:The appliance is switched off.
1. Press and hold ⁠ for approx. threeseconds.
2. Press ⁠ to confirm the messages in the display.
aThe first basic setting is shown in the display.
3. Use the control ring to change the basic setting.
4. Press ⁠.
aThe next basic setting appears in the display.
5. Use ⁠ to scroll through the basic settings and, if re-
quired, usethe control ring to change any of these
settings.
6. To save the changes, press and hold ⁠ for approx.
threeseconds.
Note:Your changes to the basic settings will be re-
tained even after a power failure.
Discarding changes to the basic settings
▶Press ⁠.
aAll changes will be discarded and not saved.
14.3 Setting the time
Requirement:The appliance is switched off.
1. Press and hold ⁠ for approx. threeseconds.
2. Press ⁠ to confirm the messages in the display.
aThe first basic setting is shown in the display.
3. Press ⁠.
aThe "Time" basic setting is shown in the display.
4. Use the control ring to change the time.
5. To save the change, press and hold ⁠ for approx.
threeseconds.
15 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
15.1 Cleaning products
In order to avoid damaging the various oven surfaces
on the appliance, do not use unsuitable cleaning
products.
WARNING‒Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶Do not use steam- or high-pressure cleaners to
clean the appliance.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶Do not use harsh or abrasive cleaning products.
▶Do not use cleaning products with a high alcohol
content.
▶Do not use hard scouring pads or cleaning
sponges.
▶Do not use any special cleaners for cleaning the ap-
pliance while it is hot.

Cleaning and servicing en
17
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
New sponge cloths contain residues from production.
▶Wash new sponge cloths thoroughly before use.
Suitable cleaning agents
Only use cleaning agents that are suitable for the differ-
ent surfaces on your appliance.
Follow the instructions on cleaning the appliance.
→"Cleaning the appliance", Page18
Appliance front
Surface Suitable cleaning agents Information
Stainless steel ¡Hot soapy water
¡Special stainless steel
cleaning products
suitable for hot sur-
faces
To prevent corrosion, remove any limescale, grease, starch or albu-
min (e.g. egg white) stains on stainless steel fronts immediately.
Apply a thin layer of the stainless steel cleaning product with a soft
cloth.
Plastic or painted
surfaces
E.g. control panel
¡Hot soapy water Do not use glass cleaner or a glass scraper.
To avoid permanent stains, remove any descaling agent that gets
onto the surface immediately.
Appliance door
Area Suitable cleaning agents Information
Door panels ¡Hot soapy water Do not use a glass scraper or a stainless steel wool.
Tip:Remove the door panels in order to clean them thoroughly.
→"Appliance door", Page20
Door cover ¡Made of stainless
steel:
Stainless steel cleaner
¡Made of plastic:
Hot soapy water
Do not use glass cleaner or a glass scraper.
Do not use stainless steel care products.
Tip:Remove the door cover for thorough cleaning.
→"Appliance door", Page20
Stainless steel in-
terior door frame
Stainless steel cleaner Discolouration can be removed using stainless steel cleaner.
Do not use stainless steel care products.
Door handle ¡Hot soapy water To avoid permanent stains, remove any descaling agent that gets
onto the surface immediately.
Door seal ¡Hot soapy water Do not remove or scrub.
Cooking compartment
Area Suitable cleaning agents Information
Enamel surfaces ¡Hot soapy water
¡Vinegar water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Leave the appliance door open to dry the cooking compartment
after cleaning it.
Notes
¡It is best to use the cleaning function.
→"Cleaning function Pyrolytic self-cleaning", Page18
¡Enamel burns at very high temperatures, causing minor discol-
ouration. The functionality of your appliance is not affected by
this.
¡The edges of thin trays cannot be completely enamelled and may
be rough. This does not impair corrosion protection.
¡Food residues will leave a white coating on the enamel surfaces.
The coating does not pose a health risk. The functionality of your
appliance is not affected by this. You can remove residues with
lemon juice.
Glass cover for
the oven light
¡Hot soapy water Use oven cleaner to remove very heavy soiling.

en Cleaning function Pyrolytic self-cleaning
18
Area Suitable cleaning agents Information
Rails ¡Hot soapy water Soak any heavily soiled areas and use a brush or steel wool.
Note:To clean thoroughly, detach the rails.
→"Rails", Page20
Pull-out system ¡Hot soapy water Use a brush to remove very heavy soiling.
Clean the pull-out rails while they are pushed in so that you do not
remove the lubricant.
Do not clean in the dishwasher.
Note:To clean thoroughly, detach the pull-out system.
→"Rails", Page20
Accessories ¡Hot soapy water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Enamelled accessories are dishwasher-safe.
15.2 Cleaning the appliance
In order to avoid damaging the appliance, you must
clean your appliance only as specified, and with suit-
able cleaning products.
WARNING‒Risk of burns!
The appliance and its parts that can be touched be-
come hot during use.
▶Caution should be exercised here in order to avoid
touching heating elements.
▶Young children under 8 years of age must be kept
away from the appliance.
WARNING‒Risk of fire!
Loose food remnants, fat and meat juices may catch
fire.
▶Before using the appliance, remove the worst of the
food residues and remnants from the cooking com-
partment, heating elements and accessories.
Requirement:Read the information on cleaning
products.
→"Cleaning products", Page16
1. Clean the appliance using hot soapy water and a
dish cloth.
‒For some surfaces, you can use alternative
cleaning agents.
→"Suitable cleaning agents", Page17
2. Dry with a soft cloth.
16 Cleaning function Pyrolytic self-cleaning
With the "Pyrolytic self-cleaning" cleaning function, the
cooking compartment is cleaned virtually automatically.
Use the cleaning function to clean the cooking com-
partment every two to three months. You can use the
cleaning function more often, if required. The cleaning
function requires approx.2.5–4.7 kilowatt hours.
16.1 Preparing the appliance for the
cleaning function
To achieve a good cleaning result and prevent dam-
age, prepare the appliance carefully.
WARNING‒Risk of fire!
Combustible objects that are left in the cooking com-
partment may catch fire.
▶Never store combustible objects in the cooking
compartment.
▶If smoke is emitted, the appliance must be switched
off or the plug must be pulled out and the door
must be held closed in order to stifle any flames.
Loose food remnants, fat and meat juices may catch
fire when the cleaning function is in progress.
▶Before starting the cleaning function, always remove
the worst of the food residues and remnants from
the cooking compartment and accessories.
The outside of the appliance gets very hot when the
cleaning function is in progress.
▶Never hang combustible objects, e.g. tea towels, on
the door handle.
▶Leave the front of the appliance clear.
▶Keep children at a safe distance.
If the door seal is damaged, a large amount of heat is
generated around the door.
▶Do not scrub or remove the seal.
▶Never operate the appliance if the seal is damaged
or missing.
1. Remove coarse dirt from the cooking compartment
and from the accessories.
2. Use a detergent solution and a soft cloth to clean
the surfaces at the edges of the cooking compart-
ment around the door seal.
Do not remove or scrub the door seal.
Use oven cleaner to remove stubborn dirt from the
inner door pane.
3. To clean an accessory as well, insert the accessory
at level 2.
Note:Only clean accessories that were included
with the appliance and that are enamelled, e.g. the
universal pan or the baking tray. Wire racks are not
suitable for the cleaning function and will become
discoloured.
4. Remove any objects from the cooking compartment.
The cooking compartment must be empty except for
the accessory that is also being cleaned.

Cleaning assistance en
19
16.2 Setting the cleaning function
Ventilate the kitchen while the cleaning function is run-
ning.
WARNING‒Risk of harm to health!
The cleaning function heats up the cooking compart-
ment to a very high temperature so that food left over
from roasting, grilling and baking will burn off. This pro-
cess releases vapours, which can irritate mucous mem-
branes.
▶Keep the kitchen well ventilated while the cleaning
function is running.
▶Do not remain in the room for long periods.
▶Keep children and pets away.
WARNING‒Risk of burns!
The cooking compartment gets very hot when the
cleaning function is in progress.
▶Never open the appliance door.
▶Allow the appliance to cool down.
▶Keep children at a safe distance.
The outside of the appliance gets very hot when the
cleaning function is in progress.
▶Never touch the appliance door.
▶Allow the appliance to cool down.
▶Keep children at a safe distance.
Note:The oven light does not light up while the clean-
ing function is running.
Requirement:→"Preparing the appliance for the
cleaning function", Page18.
1. Press ⁠.
aThe cleaning setting is highlighted in white.
2. Use the control ring to set the cleaning setting.
Cleaning set-
ting
Cleaning
level
Duration in hours
1 Low Approx. 1:15
2 Medium Approx. 1:30
3 High Approx. 2:00
Select a higher cleaning setting for heavier or older
soiling.
The duration cannot be changed.
3. Press ⁠.
aA notification stating that you should carry out the
necessary preparatory work for the cleaning func-
tion appears in the display.
4. Press ⁠ to start.
aThe cleaning function starts and the duration counts
down. The heating line does not appear.
aFor your safety, the appliance door locks once a
certain temperature is reached in the cooking com-
partment. ⁠appears in the display.
aWhen the cleaning function ends, a signal sounds
and the duration is at zero in the display.
5. Press ⁠ to switch the appliance off.
When the appliance has cooled down, the appliance
door is unlocked and ⁠goes out.
6. →"Preparing the appliance for use following the
cleaning function", Page19.
16.3 Preparing the appliance for use
following the cleaning function
1. Allow the appliance to cool down.
2. Wipe off any ash that has been left behind in the
cooking compartment, on the rails and around the
appliance door with a damp cloth.
3. Slide the pull-out rails in and out several times.
While the cleaning function is running, the rails may
become discoloured. This discolouration does not
compromise the functionality of the appliance.
4. Remove white residues with lemon juice.
Note:White residues on the enamel surfaces may
be caused by heavy soiling. These food residues
are harmless. The deposits do not compromise the
functionality of the appliance.
17 Cleaning assistance
The cleaning assistance is a quick alternative for occa-
sionally cleaning the cooking compartment. The clean-
ing assistance softens dirt by vaporising the soapy wa-
ter. It is then easier to remove dirt.
17.1 Setting the cleaning assistance
WARNING‒Risk of scalding!
If there is water in the cooking compartment when it is
hot, this may create hot steam.
▶Never pour water into the cooking compartment
when the cooking compartment is hot.
Requirement:The cooking compartment has cooled
down completely.
1. Remove the accessories from the cooking compart-
ment.
2. Mix 0.4litres water with a drop of washing-up liquid
and pour into the centre of the cooking compart-
ment floor.
Do not use distilled water.
3. Press ⁠.
4. Use the control ring to set the bottom heating ⁠.
5. Press ⁠.
6. Use the control ring to set the temperature to
80°C.
7. Press ⁠.
8. Use the control ring to set the cooking time to
fourminutes.
9. Press ⁠ to start.
aThe appliance starts to heat and the cooking time
counts down.
aWhen the time has elapsed, a signal sounds. The
time shown in the display is zero.
10. Use ⁠ to switch the appliance off and leave the
cooking compartment to cool for approx.
20minutes.

en Rails
20
17.2 Wiping down the cooking compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶After using the cleaning assistance, wipe the cook-
ing compartment and allow it to dry completely.
Requirement:The cooking compartment must have
cooled down.
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Remove stub-
born food remnants using a stainless steel scouring
pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. In order to dry the cooking compartment, leave the
appliance door open in the detent position (approx.
30°) for approx.one hour.
18 Rails
To thoroughly clean the rails and the cooking compart-
ment, or to replace the rails, you can remove the rails.
18.1 Detaching the rails
WARNING‒Risk of burns!
The shelf supports get very hot
▶Never touch the shelf supports when hot.
▶Always allow the appliance to cool down.
▶Keep children at a safe distance.
1. Lift the rail forwards slightly ⁠ and detach it ⁠.
2. Pull the whole rail to the front ⁠ and remove it.
3. Clean the rail.
→"Cleaning products", Page16
18.2 Attaching the rails
Notes
¡The rails only fit on the right or left.
¡For both pull-out rails, ensure that you can pull them
forwards and out.
1. First, push the rail into the middle of the rear
socket ⁠ until the rail rests against the cooking
compartment wall, and then push this back ⁠.
2. Push the rail into the front socket ⁠ until the rail
also rests against the cooking compartment wall,
and then press this downwards ⁠.
3
4
19 Appliance door
To clean the appliance door thoroughly, you can disas-
semble the appliance door.
19.1 Detaching the appliance door
WARNING‒Risk of injury!
Components inside the appliance door may have sharp
edges.
▶Wear protective gloves.
The hinges on the appliance door move when the door
is opened and closed, which could trap your fingers.
▶Keep your hands away from the hinges.
1. Open the appliance door fully and push in the direc-
tion of the appliance.