Bosch HBL 43 Series Service manual

BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBL 43../44../45../46..
MANUEL D'INSTALLATION
four 61ectrique Bosch encastr6,
simple et double
Models HBL 43../44../45../46..
Ed. 01-02

BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBL 43../44../45../46..
BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
IMPORTANT: Save these instructions for the local electrical inspector's use
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Please keep this manual for future reference

Table of Contents
INTRODUCTION .............................................................................................................................
TOOLS YOU WILL NEED ........................................................................................................
POWER REQUIREMENTS .......................................................................................................
CHOOSING OVEN LOCATION ...............................................................................................
STEPS FOR INSTALLATION ..................................................................................................
TECHNICAL DATA .........................................................................................................................
SINGLE OVEN ............................................................................................................................
DOUBLE OVEN ..........................................................................................................................
UNDERCOUNTER INSTALLATION ..........................................................................................
SINGLE OVEN ............................................................................................................................
WALL INSTALLATION .................................................................................................................
SINGLE OVEN ............................................................................................................................
DOUBLE OVEN ..........................................................................................................................
ELECTRICAL SUPPLY ..................................................................................................................
WIRING REQUIREMENTS ......................................................................................................
CONNECTING TO 208 VOLT CIRCUIT ...............................................................................
ELECTRICAL CONNECTIONS ...................................................................................................
3-WIRE BRANCH CIRCUIT .....................................................................................................
4-WIRE BRANCH CIRCUIT .....................................................................................................
FINAL CHECKLIST ........................................................................................................................
3
3
3
3
3
4
4
4
5
5
6
6
7
8
8
9
10
10
10
11

INTRODUCTION
Please read these instructions COMPLETELY
AND CAREFULLY. They will save you time and
effort and help to ensure optimum oven perform-
ance. Be sure to observe all WARNINGS.
These installation instructions are intended for
use by a qualified installer. In addition to these in-
structions the oven shall be installed:
• In the United States, in accordance with the Na-
tional Electric Code/State and Municipal codes
and/or local codes.
• In Canada, in accordance with Canadian Elec-
tric Code C22.1-1atest edition/Provincial and
Municipal codes and/or local codes.
These shall be carefully followed at all times.
Note: If installing your oven in Canada please
check to make sure that you have a model
with the UL Canadian listing mark, as
shown below:
The UL Canadian listing mark consists of the cir-
cled UL symbol preceded by the letter "C", as
shown. This should appear on the oven's rating
plate along with the UL United States listing
mark, which is the circled UL symbol above but
not preceded by the letter "C".
TOOLS YOU WILL NEED
The following tools are needed to install your new
oven:
• Tape measure and straightedge or ruler
• Pencil
• Phillips screwdriver
• Level
• Wire cutters and wire stripper
• 1" hole saw
• Hand or saber saw.
POWER REQUIREMENTS
The oven must be supplied with the proper volt-
age and frequency. The oven is manufactured to
be connected to a three wire or four wire, single
phase, 240 volt, 60 Hz AC electrical supply on a
separate circuit fused on both sides of the line. If
a 208 volt circuit must be used, wiring inside the
oven must be modified.
See Connection to a 208 Volt Circuit, in this
manual. A circuit breaker or time-delay fuse sized
not to exceed the circuit rating of the appliance
specified on the rating plate located on the frame
behind the door of the oven is recommended.
The oven must be supplied with copper wires
ONLY.
It is recommended that you have the electrical
wiring and hook-up of your oven performed by a
qualified electrician.
After installation is complete have the electrician
show you where the main disconnect is and which
of the circuit breakers/fuses are for the oven.
CHOOSING OVEN LOCATION
Carefully select the location where the oven will
be placed.
The oven should be located for convenient use in
the kitchen, but away from strong drafts.
Strong drafts may be caused by open doors or
windows, or by heating and/or air conditioning
vents or tans.
Make sure that electrical power can be provided
to the location selected.
STEPS FOR INSTALLATION
The following pages provide the necessary infor-
mation for proper installation of the oven ar-
ranged as tk_llows:
• Technical Data
• Installation Cutout Dimensions, Required
Clearances and Mounting instructions for:
> Undercounter Installation, Single Oven
>Wall Installation, Single Oven
>Wall Installation, Double Oven
• Electrical Supply and Wiring Requirements
• Modifications required if Connecting to 208
Volt Circuit.
• Electrical Connections for 3-wire or 4-wire
Branch Circuit.
• Final Checklist.

TECHNICAL DATA
SINGLE OVEN
For cutout dimensions see following sections titled:
Preparing Location
Single Oven
Models
HBL 432A UC
HBL 435A UC
HBL 436A UC
HBL 442A UC
HBL 445A UC
HBL 446A UC
Electrical Ratings
and Maximum Connected Load
Volts Hertz Amperes
@240V/208V
240/208 60 14/14.1
240/208 60 14/14.1
240/208 60 14/14.1
240/208 60 14/14.1
240/208 60 14/14.1
240/208 60 14/14.1
Watts
@240V/208V
3,350/2,925
3,350/2,925
3,350/2,925
3,350/2,925
3,350/2,925
3,350/2,925
Convection
Oven
No
No
No
Yes
Yes
Yes
J
DOUBLE OVEN
For cutout dimensions see following sections titled:
Preparing Location
Double Oven
Models
HBL 452A UC
HBL 455A UC
HBL 456A UC
HBL 462A UC
HBL 465A UC
HBL 466A UC
Electrical Ratings
and Maximum Connected Load
Volts Hertz Amperes
@240V/208V
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
Watts
@240V/208V
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
Convection
Oven
(top/bottom)
Yes/No
Yes/No
Yes/No
Yes/Yes
Yes/Yes
Yes/Yes
J
.g
J
J

UNDERCOUNTER INSTALLATION, SINGLE
<'3
wI
I
I
I
I
I
I
I
I
I
I
I
Oven electrical supply:
Locate unction box in
ad acent cab net or be ow
bottom support surface.
28' opening width
Bottom support surface must
be solid level and able to
support at least of 150 Ibs,
toe space area
29-1/4' width of oven door frame
!/4' min, distance
between oven door
frame and adjacent
doors or drawer fronts.
Note: Decorative inserts must
maintain minimum spacing as shown,
Secure oven to cabinet using the screws
provided. Screws should be inserted through the
mounting holes in the positions indicatedin the
frame (open door to see frame and mounting
holes), Do not overtighten screws,
Note: Decorative inserts must
maintain minimum spacing as shown.
Refer to and follow Notes and Warning listed under Wall Installation, Single Oven (facing page)

WALL INSTALLATION, SINGLE OVEN
28" openin width
Secure oven to cabinet usingtbe screws
provided. Screws should be inserted
through the mounting holes in the
positions indicated in the frame (open
door to see frame and mounting holes).
Do not overtighten screws.
o
Note: l. Do not slide oven across floor. Dam-
age to floor covering or floor could re-
sult.
2. The oven support surt:ace must be a
minimum 3/4" thick plywood plat-
form, solid, level and flush with the
bottom of the cabinet cutout.
3. Use extreme caution when moving or
installing the oven. It is very heavy.
4. Be very careful when moving or in-
stalling the oven to avoid damage to
the oven frame or damage to the cabi-
nets.
5. Be sure to level oven. An oven that is
not level may provide poor or incon-
sistent baking results.
6. Be careful when placing oven. DO
NOT pinch the conduit between the
oven back or wall and the inner cabi-
net wall or floor.
Securely t:asten oven to cabinet using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or per-
sonal injury.

WALL INSTALLATION, DOUBLE OVEN
28" open_r_ width
Secure oven to cabinet using the screws
provided. Screws should be inserted
through the mounting holes in the
positions indicated in the frame (open
door to see frame and mounting holes),
Do not overtighten screws,
Note: 1. Do not slide oven across floor. Dam-
age to floor covering or floor could re-
sult.
2. The oven support surface must be a
minimum 3/4" thick plywood plat-
form, solid, level and flush with the
bottom of the cabinet cutout.
3. Use extreme caution when moving or
installing the oven. It is very heavy.
4. Be very careful when moving or in-
stalling the oven to avoid damage to
the oven frame or damage to the cabi-
nets.
5. Be sure to level oven. An oven that is
not level may provide poor or incon-
sistent baking results.
6. Be careful when placing oven. DO
NOT pinch the conduit between the
oven back or wall and the inner cabi-
net wall or floor.
Securely fasten oven to cabinet using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or per-
sonal injury.

ELECTRICAL SUPPLY
Before installing the oven have a qualified electri-
cian verify that your home is provided with ade-
quate electrical service and that the addition of
the oven will not overload the branch circuit on
which it is to be installed. A separate three-wire
or four-wire single phase, 240 Volt, 60 Hz., or a
208 Volt, 60 Hz. branch circuit is required.
Note: For use with 208 V, 60 Hz supply voltage
the wiring must be modified as shown in
Connecting to 208 Volt Circuit.
For hook-up of the oven you will need to have an
approved junction box installed where it will be
easily reached through the front of the cabinet
where the oven will be located. The oven has 3
feet of conduit. Allow two to three feet of slack in
the line so that the oven can be moved if servicing
is ever necessary. DO NOT shorten the flexible
conduit.
ELECTRICAL SHOCK HAZARD
• The electrical power to the oven branch cir-
cuit must be shut off while line connections
are being made.
• Do not use an extension cord with this ap-
pliance.
• Electrical ground is required on this appli-
ance. The free end of the green wire (the
ground wire) must be connected to a suit-
able ground.
This wire must remain grounded to the
oven.
• If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or
other insulating materials, DO NOT use for
grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEU-
TRAL or GROUNDING circuit could result
in an electrical shock.
• Check with a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
Failure to follow these instructions could re-
sult in serious injury or death.
WIRING REQUIREMENTS
When making the wire connections, use the entire
length of the conduit provided (3 feet). The con-
duit must not be cut.
Before making connections make sure the power
is off and read and observe the following:
1. A separate three-wire or four wire, single
phase, 240 Volt, 60 Hz. or 208 Volt, 60 Hz
branch circuit is required for the oven.
2. The oven must be connected with COPPER
WIRE ONLY.
3. In the United States:
Wiring must conform to the National Electri-
cal Code, ANSI/NFPA No. 70 latest edition.
You can obtain a copy of the National Elec-
trical Code by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada:
Wiring must conform to Canadian Electrical
Code C22.1- latest edition. You can obtain
copies of the Canadian Electrical Code by
writing:
Canadian Standards Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario, Canada
M9W 1R3
4. Wire size (COPPER WIRE ONLY) and con-
nections must be suitable for the rating of the
appliance per the National Electrical Code
requirements. The flexible armored cable ex-
tending from the oven should be connected
directly to the junction box.
5. The junction box should be located so as to
allow as much slack as possible between the
junction box and the oven so it can be moved
if servicing is ever required.
6. A U.L. listed conduit connector must be pro-
vided at each end of the power supply cable.

CONNECTING TO 208 V CIRCUIT
The ovens are pre-wired for connection to 240
volt, 60 Hertz supply. If connecting to a 208 volt,
60 Hz. supply a jumper must be used across two
terminals. For the double oven models there are
two jumpers, one for the upper oven and one for
the lower oven. For the single ovens there is one
jumper.
Please refer to figures below for placement of
jumper for 208 volt, 60 hertz connection.
To connect to 208 volt circuit:
1 Remove the access panel(s) located on the
back of the oven(s).
2. Loosen the first and second screws in the ter-
minal block as shown in applicable figure
above.
3. Place the metal jumper between the first
and second screws and tighten screws to
hold jumper in place.
4. Replace access panel(s).
Placing of jumper for single oven
or upper oven of double oven,
for connection to 208 volt, 60 Hz.
Before
Jumper
Jumper
After
Placing of jumper for lower oven
of double oven, for connection to
208 volt, 60 Hz.
Before
Jumper
Jumper
After

ELECTRICAL CONNECTIONS
This appliances is manufactured with a green
GROUND wire connected to the oven chassis.
After making sure that the power has been turned
off connect the flexible conduit from the oven to
the junction box using a U.L. listed conduit con-
nector. Figures A and B and the instructions pro-
vided below present the most common way of
connecting the ovens. Your local codes and ordi-
nances, of course, take precedence to these in-
structions. Complete electrical connections ac-
cording to local codes and ordinances.
3-WIRE BRANCH CIRCUIT
Refer to Figure A, where local codes allow the
connection of GROUND wire from the oven to
the branch circuit NEUTRAL wire (grey or white
colored wire):
• If local codes permit, connect the green
GROUND wire from the oven and the white
wire from the oven to the branch circuit NEU-
TRAL wire (grey or white colored wire).
• Connect the red and black leads from the oven
to the corresponding leads in the junction box.
Junction box _ Cable from
... power supply
Red wires _"_
White wires
Bare or 9reen wire / /2_
CabUe
from oven
Grounded Neutral
_ BUaekwires
U.k.qisted conduit connector
I
Figure A.
4-WIRE BRANCH CIRCUIT
Refer to Figure B:
• Connect the green GROUND wire from the
oven to the GROUND wire in the junction box
(bare or green colored wire).
• Connect the red and black leads from the oven
to the corresponding leads in the junction box.
• Connect the white wire from the oven to the
NEUTRAL (grey or white) wire in the junction
box.
Junction box _ CaNe from
_ power supply White wires
Ungrounded Neutral
Bare or green wires BUackwires
CaNe _.
from oven _ U.L.qisted conduit connector
Figure B.
10

FINAL CHECK LIST
To prevent improper connections leading to dam-
age of electrical components and so voiding the
warranty, the following steps must be performed:
1. Check the electrical requirements and make
sure you have the correct electrical supply
and that the oven is properly grounded.
2. Make sure all control knobs are in the off po-
sition.
3. Turn on the power supply to the oven. When
the oven is first turned on the display will
come on showing all the call-outs and then
will become blank with the Set Clock sym-
bol in the upper right corner, as shown be-
low.
SET (_
0
@
J
.Check power at the junction box wires using
a volt meter having a range of 0-250 VAC. If
you have installed the oven for use on 240
volt supply you should find that the voltage
reading between the black and red wires
(Line to Line) should be 220 to 240 volts. If
you have modified the oven(s) for use on 208
volt the voltage reading between the black
and red wires should be 190 to 208 volts.
5. Set the time of day by pressing the Set
Clock button and pressing the plus (+) or mi-
nus (-) button, to the right of the display to
set the correct time. Once the time is set de-
press the Set Clock button to enter the time.
A "beep" will sound and the Set Clock sym-
bol in the upper right will disappear.
6. Turn the Mode Selector knob to Manual po-
sition, the Selector knob to Bake and turn the
Temperature knob to 350 °F. The cooling
fan, the oven lights and the heat light should
come on to indicate that the oven is heating.
The heat light will turn off when the set tem-
perature (350 °F) is reached. Turn Tempera-
ture knob to off. If you have installed a dou-
ble oven repeat test tk_r second oven.
7. To check the other oven functions refer to
the Using the Oven Controls section of the
Use and Care Manual.
8. If the oven is working properly turn the Se-
lector knob(s) and the Temperature Control
knob(s) to their off positions and turn off the
power supply to the oven.
9. Place the cover on the junction box and
make sure the cover is securely fastened and
turn on the power to the oven.
10. Leave these INSTALLATION instructions
as well as the USE AND CARE MANUAL
with the owner.
11

BOSCH
MANUEL D'INSTALLATION
four 61eetrique Bosch eneastr6, simple et double
Models HBL 43../44../45../46..
VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE COMMENCER
L'INSTALLATION
IMPORTANT: Conservez ce manuel pour l'inspecteur 61ectrique local.
INSTALLATEUR: Veuillez remettre ce manuel au propri6taire de l'appareil pour r6f6rence.
PROPRII_TAIRE: Veuillez garder ce manuel et vous en servir pour r6f6rence.

Table des mati_res
INTRODUCTION .............................................................................................................................
OUTILS DONT VOUS ALTREZ BESOIN ................................................................................
SPECIFICATIONS ELECTRIQUESREQUISES .....................................................................
CHOIX DE L'EMPLACEMENT DU FOUR ............................................................................
ETAPES DE L'INSTALLATION ..............................................................................................
DONNI_ES TECHNIQUES ..............................................................................................................
FOUR SIMPLE ............................................................................................................................
FOUR DOUBLE ..........................................................................................................................
INSTALLATION SOUS LE COMPTOIR ....................................................................................
FOUR SIMPLE ...........................................................................................................................
INSTALLATION MURALE ...........................................................................................................
FOUR SIMPLE ............................................................................................................................
FOUR DOUBLE ..........................................................................................................................
ALIMENTATION EN I_LECTRICITI_ ........................................................................................
FILS t_LECTRIQUES REQUIS .................................................................................................
CONNEXION A UN CIRCUIT )t 208 VOLTS .......................................................................
LES CONNEXIONS I_LECTRIQUES ..........................................................................................
CIRCUIT )t 3 FILS .....................................................................................................................
CIRCUIT )t 4 FILS .....................................................................................................................
LISTE DE ¥1_RIFICATION FINALE ..........................................................................................
15
15
15
15
15
16
16
16
17
17
18
18
19
20
20
21
22
22
22
23
14

INTRODUCTION
Veuillez lire enti_rement et attentivement les in-
structions contenues dans ce manuel. Cela vous
permettra de gagner du temps et d'obtenir de
meilleurs rdsultats de votre four. Prenez soin de
respecter toutes les MISES EN GARDE.
Les instructions d'installation sont destindes/_ un
installateur qualifid. En plus de ces instructions,
le four dolt etre installd comme suit:
• Aux t_tats-Unis, conformdment aux Normes d-
lectriques nationales/Normes provinciales et
municipales et/ou Normes locales.
• Au Canada, conformdment au normes cana-
diennes de l'dlectricitd, Code C22.1-derni_re d-
dition/Normes provinciales et municipales
et/ou normes locales.
Ces normes doivent etre respectdes en tout temps.
Note: Si ce four est installd au Canada, veuillez
vous assurer que votre module comporte
le symbole canadien UL indiqud ci-des-
SOUS_
Ce symbole canadien UL consiste en un cercle
dans lequel sont inscrites les lettres UL et le tout
est precede d'un "C". Ce signe doit apparaitre sur
la plaque de specifications du four, accompagnd
du symbole amdricain (meme dessin UL, mais
non precede du "C").
OUTILS DONT VOUS AUREZ BESOIN
Pour installer votre nouveau four, vous aurez be-
soin des outils suivants:
• Un ruban il mesurer et une ragle.
• Un crayon.
• Un tournevis Phillips.
• Un niveau/_ bulle d'air.
• Un coupe-ill dlectrique et un ddnudeur de fil d-
lectrique.
• Une scie pour trous de 1".
• Un scie manuelle.
SPI_CIFICATIONS I_LECTRIQUES
REQUISES
Le four doit etre alimentd par un courant de volta-
ge et de frdquence addquats. I1 doit etre relid/_ une
source de courant alternatif (C.A.) sdparde, par un
circuit /_ trois ou quatre ills /_ phase unique, 240
volts, 60Hz. Si vous devez utiliser un circuit de
208 volts, il taut absolument modifier le filage/_
l'interieur du tkmr.
Rdfdrez-vous il Connexions fi un circuit de 208
volts, dans ce manuel.
I1 est recommandd d'avoir un disjoncteur ou un
fusible empechant l'appareil d'aller au-deli_ des
limites indiqudes sur la plaque de specifications
fixde sur le cadre du four, derriere la porte.
Ce four doit etre connectd /_l'aide de ills dlectri-
ques en cuivre SEULEMENT.
Nous vous recommandons de faire installer et
brancher votre four par un dlectricien qualifid. A-
pros que l'installation est achevde, demandez /_
l'dlectricien de vous montrer o/1 se trouve le dis-
positif principal de ddbranchement et quel est le
disjoncteur/fusible du four.
CHOIX DE L'EMPLACEMENT
DU FOUR
Choisissez avec soin l'endroit o/1 vous placerez le
four.
I1 devrait etre facile d'acc_s dans la cuisine, mais
loin des courants d'air. Les courants d'air sont
causes par des portes ou fenetres ouvertes, ou en-
core par le chauffage et/ou la climatisation/venti-
lation.
Assurez-vous que l'endroit que vous avez choisi
peut facilement etre alimentd en dlectricitd.
l_TAPES DE L'INSTALLATION
Vous trouverez dans les pages qui suivent une
description, dtape par dtape, de l'installation de
votre tour. En voici les principaux elements:
• Donndes techniques
• Dimensions de l'emplacement, espacements re-
quis et instructions de montage pour:
> une installation sous le comptoir, four simple
> une installation murale, four simple
> une installation murale, four double
• Alimentation en dlectricitd et filage requis
• Modifications ndcessaires pour un circuit de
208 volts.
• Connexions dlectriques pour un circuit/_ 3 ills
ou/_ 4 ills
• Liste de verification finale
15

DONNI_ES TECHNIQUES
FOUR SIMPLE
Pour les dimensions, rdfdrez-vous _ la section intitulde
Prdparation de l'emplacement
Mod61es h
four simple
HBL 432A UC
HBL 435A UC
HBL 436A UC
HBL 442A UC
HBL 445A UC
HBL 446A UC
Spdcifications dlectriques et
charge dlectrique maximale
Volts Hertz
240/208 60
240/208 60
240/208 60
240/208 60
240/208 60
240/208 60
Amperes Watts
240V/208V 240V/208V
14/14.1 3,350/2,925
14/14.1 3,350/2,925
14/14.1 3,350/2,925
14/14.1 3,350/2,925
14/14.1 3,350/2,925
14/14.1 3,350/2,925
Fourfi
convection
Non
Non
Non
Oui
Oui
Oui
FOUR DOUBLE
Pour les dimensions, rdfdrez-vous il la section intitulde
Prdparation de l'emplacement.
Mod61es
four double
HBL 452A UC
HBL 455A UC
HBL 456A UC
HBL 462A UC
HBL 465A UC
HBL 466A UC
Spdcifications dlectriques et
charge dtectrique maximale
Volts Hertz Amperes
240V/208V
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
240/208 60 26.5/25.5
Watts
240V/208V
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
6,350/5,300
Four '_
convection
(haut/bas)
Oui/Non
Oui/Non
Oui/Non
Oui/Oui
Oui/Oui
Oui/Oui
J
J
16

INSTALLATION SOUS LE COMPTOIR, FOUR SIMPLE
O3
w
dO
I
I
I
I
I
I
I
I
I
I
I
I
I
Alimentation en electrique du four:
Localisez la bdite de derivation dans
larmoire adjacente ou sous la surface
de support inferieure,
28' Largeur de Iouverture
La surface de support inferieure dolt
@re solide, de niveau et capable de
supporter au moins !50 Ibs,
Espace de la butee
29-1/4 ' Largeur du cadre de la porte du four
1/4 ' min. de distance
entre le cadre de la
porte du four et les
portes au tiroirs adjacents.
Note: les panneaux decoratifs doivent maintenir
le minimum d'espace requis, tel quindique.
Fixez le four & I armoire & laide des vis fournies.
Les vis doivent @re inser6es dans les trous de
montage, dans les positions indiquees sue le
cadre (ouvrez la porte pour voir le cadre et les
trous de montage), Ne serrez pas les vis trop
fort,
Note: les panneaux decoratifs doivent maintenir
le minimum d'espace requis, tel quindique.
Veuillez vous rdfdrer aux notes et mises en garde mentionndes sous. Installation murale, four simple
(page opposde).
17

INSTALLATION MURALE, FOUR SIMPLE
28" Largeur de/,ouverture
Fixez le four a I'armoire & I'aide des vis fournies.
Les vis doivent _tre ins@ees dans les trous de
montage dans les positions indiquees sur le ca-
dre (ouvrez la porte pour voir le cadre et les trous
de montage), Ne serrez paa les vis trop fort,
_o
Note: 1. Ne faites pas glisser le four sur le
plancher car cela pourrait endommager
le plancher.
2. La surface de support du tour doit etre
en contre-plaqud d'une dpaisseur d'au
moins 3/4", solide, de niveau et encas-
trd dans l'alignement de l'armoire.
3. Soyez tr_s prudent lorsque vous ddpla-
cez ou installez le four. I1 est tr_s
lourd.
4. Faites attention /_ ne pas endommager
le cadre du tour ou les armoires, lors-
que vous installez le four.
5. Veillez/_ placer le four de niveau. S'il
n'est pas de niveau, les rdsultats de la
cuisson s'en ressentiront.
6. En placant le four, prenez soin de ne
pas coincer le conduit entre l'arri_re
du four ou lemur et la paroi de l'ar-
moire ou le plancher.
Fixez bien le four/_ l'armoire/_ l'aide des vis
fournies. Si vous ne le t:aites pas, cela pourrait
rdsulter en un ddplacement ou un basculement
du tour et pourrait endommager le four, les ar-
moires ou encore causer des blessures.
18