Bosch WAE20060UC/18 User manual

-The washing machine is heavy. TO AVOID RISK OF INJURY lift with caution.
-Erozen hoses can tear/burst. Do not install the washing machine outdoors or in an area
exposed to freezing conditions.
-- These installation instructions are intended for use by qualified installers. In addition to these
instructions, ifinstalling the washing machine:
In the United States comply with the National Electric Code, ANSI/NFPA70 - latest
edition/State and municil_al and/or local regulations.
In Canada comply with the Canadian Electric Code C22.1 - latest edition!provincial and
municipal and/or local regulations.
_lf the washing machine is located in a room which will be exposed to temperatures below
freezing, or if it is located in a cabin that is being shut down for the winter, any residual water
in the pump or water inlet hose(s) must be drained.
_Take care not to damage the washing machine. Do not hold on to protruding parts
(e,g. door) when lifting.
--In addition to the safety information listed here, the local water end electricity supplier may
have special requirements.
-If in doubt, have the washing machine connected by an authorized technician.
--The washer must not be stacked on top of the dryer. Serious injury and damage may result.
- Risk of personal injury or death. DO NOT stack adryer on top of the washer without the use
of one of the stacking kit accessories listed in the dryer manual.
- Stability is important to prevent washer from moving excessively during usage.
- The installation area must be firm and level.
- Soft floors/floor coverings are not suitable.
Power cord
Drainage hose F
_ , _!_;!iiiiii_
Watersupplyhoses for
hot water (redmarking)
Water supply hoses for
cold water (blue
marking)
Covers
A
w
Wrench (according to model)
Elbow
used with drain hose
Depending on the connection
- 1 hose clip ® 0.94" /24mm - 1.57" /40mm (commercially available) for connection of the
siphon -> page 4; Water connection.
Useful tools
- Bubble levelfor levelling the water.
- Y-connector (can be optained from any hardware store) in case there is only a cold water
connection.
order no. WMZ 20450.
To protect the washer drum from shifting, do not remove transportation bolt assemblies prior
............................................................to installing the washer on the pedestal.
I!
[] []
a = 39in. /100cm (approx.) d = 57in. /145cm (approx.)
b = 57in. /145cm (approx.) e = 37in. /95cm (approx.)
c = 33in. /85cm (approx.) f = 53in. !135cm (approx.)
Available commercially or from customer service:
- Longer supply hose 86 1/2 inches (2.2m approx.).
g = rain. 23in. /60cm
h = max. 39in. /100cm
II

BeforeUsingtheapplianfor firsttime,removeallthetransportation
protection devices and retain for subsequent transportation of the
/ future transport, the transport braces must be refitted -this
prevents the machine from being damaged. _> page 6,
_Keep the bolt and sleeve screwed together.
i i!i ii:i i/ :
;,, until they are freelymovable in the sleeves.
i
Water supply hose:
Attention: The water supply hose must not be kinked, bent or flattened in such a way as to
potentially diminish water flow, Also, do not cut or modify the hose.
Optimum water pressure should be between: 14.5 to 120 p.s.i. (1-10bar)
- When the faucet isturned on, the water flow is at least 2,2 U.S. gallons (8 liters) per minute.
- Ifthe water pressure is higher, install a pressure reducing valve.
Connect water supply hose to the faucet.
Attention: Plastic threads of water connections must
be hand-tightened ONLY, Do not tighten with a or:
wrench or pliers Use a Y-connector to split a single cold
Turn on the faucet (faucets) fully, water outlet in order toprovide two water
Check for leaks at the connection points, supply hose inlets.
A- c01dwater
B-hot water
(max. 60_C/140F)
- The washing machine must only be operated with cold and hot (max. 140°F/60%) faucet
water. Do not connect the appliance to the mixer faucet of an unpressurized hot-water
boiler.
- To prevent water damage, the hot and cold water valves should be accessible when the
washing machine is in place and should always be turned off when the washing machine is
not in use.
- If installing the washing machine in a new building or a building in which the plumbing system
was recently installed or upgraded, flush the lines before installing the washing machine to
remove any sand, dirt or residue.
- The connection points are under full water pressure. Check seal with faucet fully open.
- To prevent leakage or water damage, follow the instructions in this chaPrLer!
- Use only new water supply hoses, do not re-use an old hose. Only use the inlet hose
SUl_pliedor one which was purchased from an authorized dealer.
- Ifin doubt, have the appliance connected by a technician.
Water drainage hose:
Attention: Do not kink or overextend the drain hose,
Height difference between installation area and outlet:
min. 23in. /60cm - max. 39in. /100cm
Drainage into a sink/bath tub:
Attention: Secure the drainage hose to prevent it from slipping out of the sink.
Attention: The plug must not be in the plug hole. When the water is being
pumped out of the washing machine, check that the water drains away
quickly enough. Do not insert the end of the drainage hose into the
pumped off water! There is a risk that water will be drawn back into the
washing machine!
Drainage into a standpipe or in wall installation:
Use the U-bracket. Attach the U-bracket to the end of the hose and insert
end of hose into standpipe or wall drain. Use a strap or cable tie connected
to U-bracket to hold hose in place.
Drainage into a siphon:
Attention: Secure connection point with hose clip,
Q 0.94" /24mm - 1.57" /40mm
II

Strong odor. vibrations and "walking" can be the result of incorrect leveling!
Loosen counter nut with wrench counterclockwise.
Change height by rotating the appliance feet.
Attention:All four appliance feet must be firmly on the floor.
The washing machine must not wobble!
Check alignment of the washing machine with a bubble level and, if required,
correct.
Tighten the counter nut against the housing.
Hold the feet while doing this and do not change the height.
Attention: The counter nuts of all four washer feet must be screwed tightly
against the housing'
Make sure that:
- the power Iqlug fits into the socket.
_ the wire size is sufficient.
--the grounding system is properly installed.
The ROwercord maybe re_laced bYan electrician OnlYlReplacement power cords are available
from Customer Service. To reduce the risk of fire or electrical shock, DO NOT use an extension
cord or an adapter to connect the washing machine to the power supply.
Use of a Ground Fault Circuit Interrupter (GFCI) is recommended,
EleCtriCalplug:
-do not insert!pull out of the socket with damp hands.
Cdo not p,ul!the plug out of the socket by tugging the iqowercord.
- never pull out the plug while the alqpliance is operating.
Releasethe water pressure in the supply hose.
-> operating instructions, page 9; Filter in the water SUPlqly.
Drain any residual detergent solution.
-> operating instructions, page 9; Detergent solution pumA.
Isolate the washing machine from the power SUplqly.
Z_ WARNING
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will
reduce the risk of electrical shock by providing a path of least resistance for the electric current.
This appliance features a cord with an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet which has been properly installed and
grounded in accordance with all local regulations and ordinances.
Improper connection of the equipment grounding conductor may result in electric shock. Have
the appliance checked by a qualified electrician or service technician if you are in doubt as to
whether the washer has been properly grounded.
Do sot modify the plug provided with the appliance - if it will not fit in the outlet, have a proper
outlet installed by a qualified electrician.
The washing machine must only be connected to an individual branch circuit via a socket
which qas been properly installed and grounded,
The household electrical voltage must correspond to the voltage slqecifications on the washing
machine.
Connection specifications as well as the required fuses are stipulated on the appliance rating
plate.
Volts Hertz Amperes
208-240 60 10
Manufacturer (see Operating instructions) 0909 9000 351 256
!lil!

O efore calling custorner service, please check whether you can eliminate the fault yourself.
-> operating instructions, What to do if...
,,,,,,,,,,,User information explained in the instructions provided and troubleshooting issues found in the
Operating Instructions "What to do if.." section may not be covered by warranty service. Please
carefully rule any of these issues before calling for service,
... Contact inforrnation for custorner service is found in list or via our website -> operating
instruction. Please give custorner service the product number (E-Nr.) and the production
number (FD) of the appliance. You can find the rating plate which contains this
Jinformation in the frame of the open washing
E-Nr FD_, rnachine door and in the thick bordered box
Product nurnber Production nurnber on the appliance rating plate at the back of the
appliance.
,,,,,,,,,,,Please help ensure faster service by providing the product number and production number to
prevent unnecessary service calls. This will save you additional costs.
Dimensions (width x depth x height)
Weight
Mains connection (according to model)
Water pressure
23.6 x 23.2 x 33.2in. /60 x 59 x 84,2cm
167,71bs. (76kg) depending on model
Nominal voltage 208-240V, 60Hz
Nominal current 10A
Nominal power 2000-2300W
14.5 to 120p.s.i. (1-10bar)
t
Under-counter / in-cabine, installation before connection to power supply.
Installation in kitchen cabinet (under-counter or incabinet)
- Cubicle width of 23.62in. /60cm is required.
- Only install the washing machine under a continuous counter top which is securely fastened
to the neighboring cabinets.
- Ifinstalling the washer in a closet, observe the minimum distances:
Side: Oin.,rear: 3.35in. /85mm, top: Oin., front: 3.54in. /90mm
Built-under appliance
Risk of electric shock!
- 23.62in. /60cm cavity width required.
-Instead of the appliance cover panel, have a technician install a sheet metal cover;,
order no. WMZ 2420.
i
CCC_ Washing machine
Installation instructions en-us
Page
• Safety instructions ..................... 1
Installation area ........................ 1
! Scope of delivery ...................... 2
Hose and cable lengths ................. 2
IIIIIllRemove transportation safety devices ..... 3
Water connection .................... 3/4
III1!!_,.i,!.!!Leveling .............................. 5
III1!!_,.i,!.!!Electrical connection ................. 5/6
III1_Transportation (such as when moving) ..... 6
Customer service ...................... 7
W Technical specifications ................. 7
f
Under-counter/closet installation of the
rnachine ............................. 7
WARNING -to reduce the risk of fire, electric shock, or injury to persons,
//_ read the Important Safety instructions before operating this appliance.
Also follow the separate operating instructions.
Retain all documents for subsequent use or for the next owner.