Bradley Express GLX Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1901 Rev. C: ECO 20-08-028B
© 2021 Bradley
Page 1 of 70 1/21/2021
GLX-2 and TLX-2
Express Lavatory System –
GLX & TLX Series
Système lave-mains Express –
Série GLX et TLX
Sistema de lavabo Express –
Series GLX y TLX
WARNING
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.
Electrical power MUST remain off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 lb. NOTICE
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our
website at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.
GLX-2 shown with WashBar Duo WBD1
GLX-2 illustré avec WashBar Duo WBD1
Se muestra GLX-2 con WashBar Duo WBD1
TLX-2 shown with Verge™ Soap & Faucet
TLX-2 illustré avec robinet et distributeur de savon Verge™
Se muestra TLX-2 con llave y jabón Verge™

GLX-2 / TLX-2 Installation
21/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Table of Contents
Components .................................................................................................................................................................................... 3
Supplies Required ........................................................................................................................................................................... 4
Dimensions................................................................................................................................................................................ 4–11
Rough-Ins ................................................................................................................................................................................ 12–19
Bracket Mounting........................................................................................................................................................................... 20
Drain Assembly ............................................................................................................................................................................. 21
Verge Soap & Faucet or WashBar Duo Component Assembly..................................................................................................... 21
Bowl Mounting............................................................................................................................................................................... 22
Strainer and P-Trap ....................................................................................................................................................................... 22
Adjust Temperature........................................................................................................................................................................ 23
Access Panel................................................................................................................................................................................. 23
Cleaning and Maintenance............................................................................................................................................................ 24
Table des matières
Composants .................................................................................................................................................................................. 26
Fournitures requises...................................................................................................................................................................... 27
Dimensions...............................................................................................................................................................................27-34
Poses préliminaires .................................................................................................................................................................35-42
Fixation du support........................................................................................................................................................................ 43
Assemblage de l’écoulement......................................................................................................................................................... 44
Assemblage des composants Verge eau et savon ou WashBar Duo ........................................................................................... 44
Montage de la vasque................................................................................................................................................................... 45
Tamis et siphon en P..................................................................................................................................................................... 45
Régler la température.................................................................................................................................................................... 46
Panneau d’accès ........................................................................................................................................................................... 46
Nettoyage et entretien ................................................................................................................................................................... 47
Contenido
Componentes ................................................................................................................................................................................ 49
Materiales necesarios ................................................................................................................................................................... 50
Dimensiones............................................................................................................................................................................ 50–57
Tuberías empotradas................................................................................................................................................................58-65
Montaje de los soportes................................................................................................................................................................ 66
Conjunto de desagüe .................................................................................................................................................................... 67
Conjunto de componentes de llave y jabón Verge o WashBar Duo.............................................................................................. 67
Montaje de la palangana............................................................................................................................................................... 68
Filtro y sifón en P .......................................................................................................................................................................... 68
Ajuste de temperatura ................................................................................................................................................................... 69
Panel de acceso............................................................................................................................................................................ 69
Limpieza y mantenimiento............................................................................................................................................................. 70

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 3
Components
Access Panel
(186-2290)
Bowl
Contact your Bradley Representative
for color options
Individual Rough-In Option
Chrome P-Trap (S29-094)
Plastic P-Trap (269-1697)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Prepack
(S45-3008) *Screw
Strainer
Wall Bracket
(140-1128)
Access Panel
Bracket
(140-1172)
#10 Access Panel
Thumb Screw
(160-536)
GLX-2
(187-367)
(color dependent) TLX-2
(187-366)
(color dependent)
Combined Rough-In Option
Chrome Waste Assembly (S45-2654)
Plastic Waste Assembly (S45-2662)
TMV Valve
(½" NPTM Outlet)
(S45-2701)
Hose Prepack
(S45-2730)
TMV Supply Connections
Plastic Hose
Hose Prepack
(S45-2731)
Tempered Supply Connections
Plastic
Hose
Plastic Hose
Stainless
Steel
Hose
Supply Fittings
(Standard)
(S45-2510)
and
(S45-2999)
for Verge Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700
Supply Fittings
(Standard)
(S45-2511)
and
(S45-3000)
for Verge Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700

GLX-2 / TLX-2 Installation
41/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – GLX-2 (shown with Verge™ Soap & Faucet)
Front View – GLX-2 (shown with Verge Soap & Faucet)
Supplies Required
• (6) ³⁄₈" fasteners and wall anchors (minimum pull-out rating of 1,000 lb)
• (4) ¼" fasteners (2 for the bowl, 2 for the bracket)
• ½" hot/cold or tempered stub-out(s)
• 1½" NPT drain stub-out(s)
• OPTIONAL: (3) 110V GFCI protected electrical outlets for 100–120 VAC plug-in transformers
• Screen filter(s) as needed, if not included with faucet(s)
20⁵⁄₈"
(525)
6" (152)
4⁵⁄₈" (118)
2⁹⁄₁₆" (65)
5¹⁄₈" (130)
55³⁄₈" (1406)
28" (711)
13¹¹⁄₁₆" (348)
47¾" (1213)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 5
Dimensions (mm)
Top View – GLX-2 (shown with WBD1)
Front View – GLX-2 (shown with WBD1)
20⁵⁄₈"
(525)
4" (102)
5¹⁄₈" (130)
55³⁄₈" (1406)
28" (711)
13¹¹⁄₁₆" (348)
47¾" (1213)
34"
(864)
19¹⁄₈"
(486)
Finished Floor
7¹⁄₈" (181)

GLX-2 / TLX-2 Installation
61/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – TLX-2 (shown with Verge Soap & Faucet)
Front View – TLX-2 (shown with Verge Soap & Faucet)
20⁵⁄₈"
(525)
6" (152) 6" (152)
2⁹⁄₁₆" (65)
5¹⁄₈" (130)
55⁵⁄₁₆" (1404)
25⁵⁄₁₆" (642)
15" (381)
47¾" (1213)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 7
Dimensions (mm)
Top View – TLX-2 (shown with WBD1)
Front View – TLX-2 (shown with WBD1)
20⁵⁄₈"
(524)
4" (102)
5" (127)
55⁵⁄₁₆" (1404)
25⁵⁄₁₆" (642)
15" (381)
47¾" (1213)
7¹⁄₈" (181)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

GLX-2 / TLX-2 Installation
81/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – GLX-2
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6⁷/₈" (175)
6⁷⁄₈" (175)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 9
Dimensions (mm)
Side View – GLX2
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
12⁷⁄₈"
(326)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6⁷/₈" (173)
6⁷⁄₈" (173)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-2 / TLX-2 Installation
10 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – TLX-2
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 11
Dimensions (mm)
Side View – TLX-2
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½"(445)
12¾"
(325)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-2 / TLX-2 Installation
12 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
AInstall (1) ³⁄₈" wall anchor with a minimum pull-out force of 1,000 lb per local codes at locations shown 2
B Install (2) wall anchors per bracket with a minimum pull-out force of 100 lb per local codes at locations shown 2
C Provide structural backing compliant with local building codes. 2
Structural Rough-Ins (mm)
Areas highlighted in gray require sufficient backing
compliant with local building codes.
RIM
HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE NOTES
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Secure bracket to wall using min. (2) ³⁄₈"
anchor bolts to the left of C/L and min. (2)
³⁄₈" anchor bolts to the right of C/L. The (2)
anchor bolts to the right of C/L must be
min. 16" apart from the anchor bolts to the
left of C/L. When mounting is complete,
check to ensure the bracket is level.
34"
(864)
31¼"
(794)
C
L
B
A A
B
Finished
Floor
36½" (927)
C
31½"
(801)
12"
(305)
23" (584)
5⁵/₁₆" (135)
5³/₁₆" (131)
16"
(407)
30½"
(775)
¾" (19)
Access Panel
Mounting Bracket

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 13
Plumbing & Electrical Rough-Ins – GLX Combined Waste (mm)
Mounting for Standard ADA and TAS height shown.
Combined waste option is not available for use with
WBD1 faucet assembly.
Electric outlet locations shown below reflect potential locations.
Refer to the tech data for power supply and outlet information.
3" (76)
3" (76)
1½" (38)
6" (152)
16½"
(419)
20"
(508)
34"
(864)
22"
(559)
Finished Floor
EE A
HC
C
L
C
L
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, combined waste option 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 2
14¼" (368) 14" (356)
Finished Floor
A
34"
(864)

GLX-2 / TLX-2 Installation
14 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Plumbing & Electrical Rough-Ins – GLX Individual Waste (mm)
Mounting for Standard ADA and TAS height shown.
VERGE SOAP & FAUCET POWER SUPPLY
1-Station 2-Station 3-Station
Faucet Only AC Adapter x 1
1 duplex outlet req. AC Adapter x 2 1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req.
Soap Only AC Adapter x 1
1 duplex outlet req. AC Adapter x 2 1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req.
Faucet & Soap AC Adapter x 2
1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req. AC Splitter* x 2 1 duplex outlet req.
Soap & Multi-Feed NA NA AC Splitter* x 1
1 duplex outlet req.
Faucet, Soap, & Multi-Feed NA NA AC Splitter* x 2
1 duplex outlet req.
*AC splitter assembly includes one adapter, one 4-way splitter, and four extensions.
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, individual waste option 2
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 2
3" (76)
3" (76)
1½" (38)
6" (152)
14" (356) 14" (356)
16½"
(419)
20"
(508)
34"
(864)
27"
(686)
Finished Floor
EE
A A
HC
C
L

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 15
Plumbing and Electrical Rough-Ins – TLX Waste (mm)
Mounting for Standard ADA and TAS height shown.
VERGE SOAP & FAUCET POWER SUPPLY
1-Station 2-Station 3-Station
Faucet Only AC Adapter x 1
1 duplex outlet req. AC Adapter x 2 1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req.
Soap Only AC Adapter x 1
1 duplex outlet req. AC Adapter x 2 1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req.
Faucet & Soap AC Adapter x 2
1 duplex outlet req. AC Splitter* x 1 1 duplex outlet req. AC Splitter* x 2 1 duplex outlet req.
Soap & Multi-Feed NA NA AC Splitter* x 1
1 duplex outlet req.
Faucet, Soap, & Multi-Feed NA NA AC Splitter* x 2
1 duplex outlet req.
*AC splitter assembly includes one adapter, one 4-way splitter, and four extensions.
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 2
3" (76)
3" (76)
1½" (38)
6" (152)
16½"
(419)
34"
(864)
27"
(686)
Finished Floor
EE
A
HC
C
L

GLX-2 / TLX-2 Installation
16 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Plumbing & Electrical Rough-Ins – Verge Soap & Faucet (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
F#10 Anchors for Faucet Control Box Installation
Provide sufficient backing behind the mounting locations. 4
6½" (165)
10"
(254)
2¹⁄₈"
(55)
5⁵⁄₈"
(143)
34"
(864)
15"
(381)
13½" (343)13" (330)
6" (152)
1³⁄₁₆" (30)
4¾" (121)
Finished Floor
Mixing Valve
Faucet Box
(2x)
FF
FF
C
L

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 17
Plumbing & Electrical Rough-Ins – WBD1 (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Bracket (100 lb pull out force)
Provide sufficient backing behind the mounting locations. 12
6¾"
(171)
3¼"
(83)
10"
(254)
2" (51)
6½" (165)
34"
(864)
17³⁄₈"
(441)
3½" (89)
18⁵⁄₁₆" (466)
16½" (419)
6³⁄₁₆" (156)
5" (127)
5" (127)16¼" (413)5½" (140)
6" (152)
5¼"
(133)
4¹⁄₈" (105)
Finished Floor
Master Controller
(2x)
Soap Tank
(2x)
Mixing
Valve
G
G
G
G
G
G
G
G
G G
G G
C
L
Combined waste option is not available for use with
WBD1 faucet assembly.

GLX-2 / TLX-2 Installation
18 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Rough-Ins – Verge Individual Top-Feed Soap (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Installation
Provide sufficient backing behind the mounting locations. 4
7"
(178)
3¹/₈" (80)
5½" (140) 18" (457)
10½"
(267)
5¹⁄₈" (131)
34"
(864)
4½" (114) 6¹⁄₁₆" (155)
Finished Floor
Soap Battery Box
(2x)
Individual Top-Feed
Control Box/Tank
(2)
C
L
G GG G

Installation GLX-2 / TLX-2
Bradley • 215-1901 Rev. C: ECO 20-08-028B 1/21/2021 19
Rough-Ins – Verge Multi-Feed Soap (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Installation
Provide sufficient backing behind the mounting locations. 4
6⁷⁄₁₆"
(164)
5½" (140) 3¹/₈" (80) 7" (178)
18" (457)
6⁵⁄₁₆" (161) 15⁹⁄₁₆" (395)
10½"
(267)
5¹⁄₈" (131)
34"
(864)
4½" (114) 6¹⁄₁₆" (155)
Finished Floor
Multi-Feed
Control Box
(2x)
Soap Battery Box
(2x)
Use Velcro to attach battery box
to front top ledge of the tank.
Multi-Feed
Tank
G GG G

GLX-2 / TLX-2 Installation
20 1/21/2021 Bradley • 215-1901 Rev. C: ECO 20-08-028B
Bracket Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
1
13¹⁄₈"
(333)
28" (711)
12¼" (311) 12¼" (311)
28" (711)
30½"
(775)
Locating Notch
Install wall bracket to wall
per structural rough-in
dimensions. Check to
ensure the bracket is
level. Example anchor
locations shown.
A
Locating Notch
Finished Floor
Measure down using the center location
notch on the wall bracket. Draw a
horizontal line and mark 28"locations to
the right and left of the center bracket.
B
Install the remaining trap cover brackets at the
locations defined by the horizontal line draw in
Step B and marked at 28"both to the left and right
of the center bracket. Secure the brackets to the wall
anchors using fasteners per the structural rough-in
requirement (supplied by installer) (2x).
C
Mounting height per structural rough-in dimensions.