Bradley Express GLX Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1900 Rev. C: ECO 20-08-028B
© 2021 Bradley
Page 1 of 58 1/21/2021
GLX-1 and TLX-1
Express Lavatory System –
GLX & TLX Series
Système lave-mains Express –
Série GLX et TLX
Sistema de lavabo Express –
Series GLX y TLX
WARNING
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.
Electrical power MUST remain off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 lb. NOTICE
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our
website at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.
GLX-1 shown with WashBar Duo WBD1
GLX-1 illustré avec WashBar Duo WBD1
Se muestra GLX-1 con WashBar Duo WBD1
TLX-1 shown with Verge™ Soap & Faucet
TLX-1 illustré avec robinet et distributeur de savon Verge™
Se muestra TLX-1 con llave y jabón Verge™

GLX-1 / TLX-1 Installation
21/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Table of Contents
Components .................................................................................................................................................................................... 3
Supplies Required ........................................................................................................................................................................... 4
Dimensions................................................................................................................................................................................ 4–11
Rough-Ins ................................................................................................................................................................................ 12–15
Bracket Mounting........................................................................................................................................................................... 16
Drain Assembly ............................................................................................................................................................................. 17
Verge Soap & Faucet or WashBar Duo Component Assembly..................................................................................................... 17
Bowl Mounting............................................................................................................................................................................... 18
Strainer and P-Trap ....................................................................................................................................................................... 18
Adjust Temperature........................................................................................................................................................................ 19
Access Panel................................................................................................................................................................................. 19
Cleaning and Maintenance............................................................................................................................................................ 20
Table des matières
Composants .................................................................................................................................................................................. 22
Fournitures requises...................................................................................................................................................................... 23
Dimensions...............................................................................................................................................................................24-30
Poses préliminaires .................................................................................................................................................................31-33
Fixation du support........................................................................................................................................................................ 35
Assemblage de l’écoulement......................................................................................................................................................... 36
Assemblage des composants Verge eau et savon ou WashBar Duo ........................................................................................... 36
Montage de la vasque................................................................................................................................................................... 37
Tamis et siphon en P..................................................................................................................................................................... 37
Régler la température.................................................................................................................................................................... 38
Panneau d’accès ........................................................................................................................................................................... 38
Nettoyage et entretien ................................................................................................................................................................... 39
Contenido
Componentes ................................................................................................................................................................................ 41
Materiales necesarios ................................................................................................................................................................... 42
Dimensiones............................................................................................................................................................................ 43–49
Tuberías empotradas................................................................................................................................................................50-53
Montaje de los soportes................................................................................................................................................................ 54
Conjunto de desagüe .................................................................................................................................................................... 55
Conjunto de componentes de llave y jabón Verge o WashBar Duo.............................................................................................. 55
Montaje de la palangana............................................................................................................................................................... 56
Filtro y sifón en P .......................................................................................................................................................................... 56
Ajuste de temperatura ................................................................................................................................................................... 57
Panel de acceso............................................................................................................................................................................ 57
Limpieza y mantenimiento............................................................................................................................................................. 58

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 3
Components
Access Panel
(186-2273)
Bowl
Contact your Bradley Representative
for color options
Individual Rough-In Option
Chrome P-Trap (S29-094)
Plastic P-Trap (269-1697)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Prepack
(S45-3008) *Screw
Strainer
Access Panel
Bracket
(140-1172)
#10 Access Panel
Thumb Screw
(160-536)
Wall Bracket
(140-1153)
TMV Valve
(½" NPTM
Outlet)
(S45-2701)
Hose Prepack
(S45-2730)
Supply
Fittings
(S45-2712)
Hose Prepack
(S45-2702)
Plastic Hose
Plastic
Hose
TMV & Tempered Supply Connections
TMV Supply Connections
Two (2) connections
are required for TMV.
Use for faucets not
supplied by Bradley
that require a TMV.
GLX-1
(187-365)
(color dependent)
TLX-1
(187-364)
(color dependent)

GLX-1 / TLX-1 Installation
41/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – GLX-1 (shown with Verge™ Soap & Faucet)
Front View – GLX-1 (shown with Verge Soap & Faucet)
Supplies Required
• (4) ³⁄₈" fasteners and wall anchors (minimum pull-out rating of 1,000 lb)
• (4) ¼" fasteners (2 for the bowl, 2 for the bracket)
• ½" hot/cold or tempered stub-out(s)
• 1½" NPT drain stub-out(s)
• OPTIONAL: (3) 110V GFCI protected electrical outlets for 100–120 VAC plug-in transformers
• Screen filter(s) as needed, if not included with faucet(s)
20⁵⁄₈"
(525)
6"
(152)
26³⁄₈" (670)
13¹⁄₈" (335)
5¹⁄₈" (130)
18⁷⁄₈" (478)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 5
Dimensions (mm)
Top View – GLX-1 (shown with WBD1)
Front View – GLX-1 (shown with WBD1)
18⁷⁄₈" (478)
34"
(864)
19¹⁄₈"
(486)
Finished Floor
20⁵⁄₈"
(525)
26³⁄₈" (670)
13¹⁄₈" (335)
8¹⁄₈"
(233)
5¹⁄₈" (130)

GLX-1 / TLX-1 Installation
61/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – TLX-1 (shown with Verge Soap & Faucet)
Front View – TLX-1 (shown with Verge Soap & Faucet)
20⁵⁄₈"
(525)
6" (152)
26¼" (668)
13¹⁄₈" (335)
5¹⁄₈" (130)
18⁷⁄₈" (478)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 7
Dimensions (mm)
Top View – TLX-1 (shown with WBD1)
Front View – TLX-1 (shown with WBD1)
20⁵⁄₈"
(525)
4" (102)
26¼" (668)
13¹⁄₈" (335)
5¹⁄₈" (130)
18⁷⁄₈" (478)
7¹⁄₈" (181)
34"
(864)
19¹⁄₈"
(486)
Finished Floor

GLX-1 / TLX-1 Installation
81/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – GLX-1
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6⁷/₈" (175)
6⁷⁄₈" (175)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 9
Dimensions (mm)
Side View – GLX-1
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
12⁷⁄₈"
(326)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6⁷/₈" (173)
6⁷⁄₈" (173)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-1 / TLX-1 Installation
10 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – TLX-1
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 11
Dimensions (mm)
Side View – TLX-1
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½"(445)
12¾"
(325)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-1 / TLX-1 Installation
12 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
AInstall (1) ³⁄₈" wall anchor with a minimum pull-out force of 1,000 lb per local codes at locations shown 2
B Install (2) wall anchors per bracket with a minimum pull-out force of 100 lb per local codes at locations shown 2
C Provide structural backing compliant with local building codes. 2
Structural Rough-Ins – GLX & TLX (mm)
RIM
HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE NOTES
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Areas highlighted in gray require sufficient backing
compliant with local building codes.
Secure bracket to wall using min. (2) ³⁄₈"
anchor bolts to the left of C/L and min. (2)
³⁄₈" anchor bolts to the right of C/L. The (2)
anchor bolts to the right of C/L must be
min. 16" apart from the anchor bolts to the
left of C/L. When mounting is complete,
check to ensure the bracket is level.
34"
(864)
31¼"
(794)
C
L
A A
B
Finished Floor
Access Panel
Mounting Bracket
10" (254)
¾" (19)
C
31½"
(801)
Bracket Slots
to Finished
Floor
8¼"
(210)
Wall Bracket
16"
(407)
30½"
(775) Bottom of Wall
Bracket to
Finished Floor

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 13
Plumbing & Electrical Rough-Ins – GLX & TLX (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 1
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
1" (25)
27"
(686)
34"
(864)
18½"
(470)
22½"
(571)
Finished Floor
A
E
H C
C
L

GLX-1 / TLX-1 Installation
14 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Plumbing & Electrical Rough-Ins – Verge Soap & Faucet (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
F#10 Anchors for Faucet Control Box Installation
Provide sufficient backing behind the mounting locations. 2
G#10 Anchors for Soap Tank Bracket (100 lb pull out force)
Provide sufficient backing behind the mounting locations. 2
5½" (139)
10"
(254)
6"
(152)
5¹⁄₈"
(131)
34"
(864)
6½" (165)
6³⁄₈" (161) 3¹⁄₈" (80)
6⁵⁄₈" (169)
9" (229)
Finished
Floor
Soap Battery
Box
Faucet Box
Individual
Top-Feed
Control
Box/Tank
F
G G
F
C
L
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 15
Plumbing & Electrical Rough-Ins – WBD1 (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Bracket (100 lb pull out force)
Provide sufficient backing behind the mounting locations. 6
Combined waste option is not available for use with
WBD1 faucet assembly.
2"
(51)
2"
(51)
17³⁄₈"
(441)
10"
(254)
6"
(152)
34"
(864)
5½" (140)
7¾" (197)
4¹⁄₈" (105) 3½" (89)
5" (127)
5" (127)
4" (102)
2½" (64)
Finished
Floor
Soap
Tank
Mixing
Valve
G
G
G
G
G
G
C
L
Master Controller

GLX-1 / TLX-1 Installation
16 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Bracket Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
1
13¹⁄₈" REF
(333)
30½"
(775)
Install wall bracket to wall
per structural rough-in
dimensions. Check to
ensure the bracket is
level. Example anchor
locations shown.
A
Locating Notch
Finished Floor
Measure down 13¹⁄₈" to top of
bracket. Secure the bracket to the
wall anchors using fasteners per
the structural rough-in requirement
(supplied by installer) (1x).
B
Mounting height per structural rough-in dimensions.
(mm)

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 17
Drain Assembly
Verge Soap & Faucet or WashBar Duo Component Assembly
2
3
For ease of drain installation, lay the bowl on its back.
IMPORTANT: While the bowl is free from the wall, assemble
the components for the Verge soap & faucet or WashBar Duo
assemblies. Refer to the Verge soap & faucet and WashBar Duo
installation instructions.
O-Ring
Drain
Adapter
Packing
Washer
#10-24
Screw
Assemble the components as shown and
thread the four screws through the drain
adapter and into the basin inserts. Ensure
the screws compress the drain adapter
evenly onto the basin.
A

GLX-1 / TLX-1 Installation
18 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Bowl Mounting (to Frame and Wall)
4
Strainer and P-Trap
5
Strainer
Thread the strainer screw
through the strainer and
into the stand off on the
drain adapter.
A
Position bowl above wall bracket.
Press firmly on the back of the bowl
to seat the bowl flange into the wall
bracket lip. Ensure bowl is level.
ASecure the bowl to the wall anchors
using fasteners per the structural
rough-in requirement (supplied by
installer).
B
Ensure not to overtighten the strainer screw.
WARNING! Ensure bowl is level and completely seated in the wall bracket.

Installation GLX-1 / TLX-1
Bradley • 215-1900 Rev. C: ECO 20-08-028B 1/21/2021 19
Make all connections before installing access panel. Combined
waste arms to be cut in field to accommodate rough in location.
Shown with WashBar Duo. Verge Soap and Faucet similar.
Access Panel
7
Hang the access panel onto
the access panel bracket as
shown, and then secure the
access panel with the thumb
screw provided.
A
Adjust Temperature with Water Running
H
C
ALoosen Cap Screw about ¹⁄₄" (4-6 turns)
and lift up cover (do not remove).
B
Using cover, turn cartridge gently until
desired water temperature is reached.
Do not turn past stops as this may
damage unit. Push cover down and
tighten screw.
This valve is NOT factory preset.
Upon installation, the temperature
of this valve must be checked and
adjusted to ensure delivery of a
safe water temperature. Water
in excess of 110°F (43°C) may
cause scalding.
6

GLX-1 / TLX-1 Installation
20 1/21/2021 Bradley • 215-1900 Rev. C: ECO 20-08-028B
Cleaning and Maintenance for Terreon®(Basin)
Material Description: Terreon is a densified solid surface material composed of bio based resin and is resistant to chemicals,
stains, burns and impact. Surface can be easily repaired with everyday cleansers or fine grit abrasives. Because Terreon is a
unique cast material, its aggregate flow and distribution, and shades of color can vary from product to product creating natural
characteristics.
Routine Cleaning: For regular cleaning, use mild neutral base cleaners.
Stubborn Stains: Remove tough stains with Soft-Scrub®and a green Scotch-Brite®pad or lightly sand in a circular motion with
240 grit wet/dry sandpaper. The finish can then be renewed with a maroon Scotch-Brite pad.
Scratches: Remove scratches with a green Scotch-Brite pad. The finish can then be renewed with a maroon Scotch-Brite pad.
Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly
after cleaning.
Restoring the surface: Use Hope’s
®
Perfect Countertop to refresh and protect the Terreon Solid Surface material. Dark Terreon
colors may require additional care and maintenance. For complete instructions on this additional maintenance, visit bradleycorp.com.
Repair Kits: Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing.
Repair kits are made to order and have a shelf life of 30 days.
NOTICE! Do not use strong acid or alkaline chemicals and cleaners to clean Terreon. If these chemicals
come in contact with the surface, wipe them off immediately and rinse with soapy water. Avoid
contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot
pans and objects.
Cleaning and Maintenance for Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly
under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the
cleaning solution per the manufacturer's instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®stainless steel
cleaner or a soft abrasive. Always follow the manufacturer's instructions and apply in the same direction as the polish lines.
NOTICE! Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool
or stainless steel brushes.
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance
with the manufacturer's instructions. Many of these products leave a protective coating that helps prevent future smears and
fingerprints.
Grease and Oil: To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the
manufacturer's instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
NOTICE! Do not permit salty solutions to evaporate and dry on stainless steel.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source
of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
NOTICE! Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use
of these cleaners should be avoided.