BRAND-MAN BG2211A3 User manual

OWNER’S MANUAL
MD
CONVERSION INSTRUCTION FROM
PROPANE TO NATURAL GAS
WARNING
with the manufa cturer’ s instructions and all appli cable codes and requirements
of the authority having jurisdiction. If the information in these inst ructions is not
agency is responsible for the proper and complete until the operation of the con-
-
plied with the kit.”
Conversion kit suitable for BG2211A3/BG2211B3/
BG2211A4 /BG2211A6
TEL: [phone]
Tools are NOT included.

WARNING!
PRECAUTIONARY LEAK TEST
LEAK TESTS MUST BE CARRIED OUT IN A WELL VENTILATED AREA
• ‘OFF’
position.
•Open the gas control valve on the gas cylinder or regulator.
•To check for gas leaks a solution of soapy water is required
NEVER USE AN OPEN FLAME TO CARRY OUT A GAS LEAK TEST
•The gas piping system MUST be checked for leaks by brushing the soapy water solution across
each joint including valve connections, hose connections, side burner connections and regulator
connections
•If bubbles appear across any joint or connection there is a leak:
oImmediately turn the gas cylinder valve ‘OFF’.
oCheck and retighten all gas connections and joints.
oRepeat section PRECAUTIONARY LEAK TEST.
oIf the leak has been corrected then the barbecue can be used.
o DO NOT USE YOUR BARBECUE, contact the customer
service centre as listed on the warranty card for assistance.
IT IS RECOMMENDED THAT A LEAK TEST BE CARRIED OUT ON A YEARLY BASIS
CHECK GAS CYLINDER CONNECTION WHEN EXCHANGING GAS CYLINDER
BARBECUE NATURAL GAS DETAILS
•Main burner: 10,000 BTU
•Side burner: 12,000BTU

ASSEMBLY INSTRUCTIONS (CONTINUE)
ASSEMBLY INSTRUCTIONS
Step 1 1) Open the BBQ hood.
3) Put it aside.
Step 2 1) Remove the R-pin at the end of the burner as in Figure 4.
2) Remove all the burners carefully and put it aside as in Figure 5.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5

ASSEMBLY INSTRUCTIONS
1) Unscrew the Propane injectors out in the anti-clockwise direction.
2) Put the Propane injectors in a safe place. The injector is a 2 step unit. Remove the
Propane injector and the NG injector is already there and ready for use.
Note: when unscrew and screw on the injectors from or onto the valve carefully and
dont overpressure. Please use a 6mm nut driver to operate (Tool is NOT included).
Step 3
Step 4 1) Insert back all burner as in Figure 6 and 7.
2) Secure all burner with the R Pin as in Figure 8 and 9.
Figure 6
Figure 7
Figure 8
Figure 9

ASSEMBLY INSTRUCTIONS
Step 5
Figure 1
Figure 2
Figure 3
Figure 5
Figure 6
Figure 4
Step 6 1) Remove the two screws underneath the side burner as in Figure 1.
2) Remove the trivet and the side burner (Figure 2).
3) Replace the LPG injector carefully as shown in Figure 3.
Don’t use too much force that can break the valve.
4) Put back in the side burner (Figure 4).
5) Secure back the side burner with the two screws removed in step 1 as in Figure 5.
6) Put back the trivet (Figure 6).
Note: This step does not apply to BG2211A3.

ASSEMBLY INSTRUCTIONS
Step 7
Figure 1
Figure 2
1) Remove the Propane hose & regulator from the manifold as shown below.
2) Connect the Natural Gas hose onto the connector at the end of the manifold as
show below.
3) Connect to the Natural Gas supply connector at your property.
Note: Ensure to run a leak test with soapy water after the NG hose changeover.
Natural Gas Hose
Step 8 1) Stick on the Natural Gas Warning Label behind the cart door as shown below.

ASSEMBLY INSTRUCTIONS
Step 9
Pull back collar on
connector
1) Connecting the NG quick connect to the NG supply as shown below.
Note: ensure the NG supply valve is in OFF position before connecting or disconnecting.

OPERATING INSTRUCTION
Operating Main Burners
First Use
moved from the Barbecue.
2. Light Barbecue per “Lighting” section.
3. Remove manufacturing oils before cooking on this Barbecue for the
4. Season your Barbecue cooking surface per “Seasoning Barbecue”
section.
Lighting
CAUTION: Keep outdoor gas cooking appliance area clear and free
liquids.
CAUTION: Check and clean burner/venturi tubes for insects and insect
CAUTION: Do NOT use non-stick cooking sprays because they contain
a lot of water and can burn onto the Barbecue, damaging the surface.
CAUTION: Do NOT use corn oil as it contains a high level of sugar, which
can carmelize and burn onto the surface.
1. Open hoods.
webs can clog the burner/venturi tube. A clogged burner tube can
3. All control knobs must be in the “OFF ” position (Figure 1).
4. Ensure the natural gas hose is connected.
Figure 3
Figure 4
Figure 1
Figure 2
5. Turn NG gas valve to “OPEN.”
6. Push and turn any control knob to (HIGH). The burner should light. If it
does not, repeat up to three times.
7. If ignition does not occur in 5 seconds, turn burner control knob “OFF”, wait
5 minutes, and repeat lighting procedure.
8. If igniter does not light burner, use a lit match secured with the Lighting
Rod (included with the Barbecue) to light burners. Access the burners as
(Figures 3 and 4). Position lit match near side of burner (Figures 3 and 4).
Important: Always use the Lighting Rod (included) when lighting burners with
a match.
Note: Each burner lights independently - repeat steps 5-9 for the other burners.
the control knobs to the “OFF” position, turn the LP gas tank valve to
“CLOSED” and open lid to let the gas clear for 5 minutes before relighting.
Figure 5
Burner
Flame Slight
Yellow
Slight
Blue
Dark
Blue

OPERATING INSTRUCTION
1. Turn NG gas valve to“CLOSED”.
3. Turn all control knobs clockwise to the “OFF” position.
Note: A “poof”sound is normal as the last of the NG gas is burned.
Controlling Flare-ups
CAUTION:
in serious burns, bodily harm or other damage.
ur.
Do NOT attempt to extinguish with water.
Important:
DO NOT
Minimize Flare-ups:
1. Trim excess fat from meats prior to cooking.
2. Cook high fat content meats on (LOW) setting or indirectly.
3. Ensure that your Barbecue is on a hard, level, non-combustible surface and the grease is allowed to drain
into grease receptacle.