Brateck LPA13-444 User manual

INSTALLATION INSTRUCTIONS
Full-motion Wall Mount
ISSUED: OCT. 2012
4. Adjustment
Adjust to desired location or tilt.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
7
+15°
-15°
+5°
-5°
Tighten the two bolts by using a proper phillips screwdriver to secure bracket.
wall
safety bolt
120°
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
200x200/300x300
400x200/400x400 47"
MAX 45kg45kg
(99lbs)(99lbs)
MAXMAX
45kg
(99lbs)
MAX
LPA13-444
400x200/400x400
600x400/800x400 63"
MAX 60kg60kg
(132lbs)(132lbs)
MAXMAX
60kg
(132lbs)
MAX
LPA13-484

21
NOTE: Read the entire instruction manual before you start installation and assembly. Component Checklist
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. Use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package W
ST6.3x55 (x6)
W-A
concrete anchor (x6)
W-B
D6 washer (x6)
W-C
adapter bracket (x2)
B
articulated arm assembly (x1)
A
Package M
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer (x4)
M-F
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G

4
3
X X
√
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
1a. Mount on Wood Stud Wall
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1b. Mount on Solid Brick and Concrete Block
Screw the wall
mount onto
the wall
Screw the wall
mount onto
the wall
X X
√
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
2
1
Drill pilot holes
3
Find and mark the
exact location of
mounting holes
Drill pilot holes
1
2
Mark the
exact location of
mounting holes
W-A
W-B
W-C
W-A
W-C

65
2-2 For Recessed Back Screen or to Access A/V Inputs
TV
TV
TV
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the display.
· Screw the adapter brackets onto the display.
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
2. Install Adapter Brackets
2-1 For Flat Back Screen
TV
TV
TV
Top of display
M-A
M-B
M-C
M-F
or or or
M-C M-C
M-D
M-E
M-F
M-G
M-F
M-G
M-D
M-E
M-F
M-H
M-D
M-E
M-F
M-H
M-G
M-G
3. Hook the Display onto the Wall Mount
wall