Bright Networking TC300 User guide

5
Table of Contents
NOTE:4
CHAPTER 1 SYSTEM CONFIGURATION 1
1-1 SYSTEM GENERAL INFORMATION 1
1-2 PRECAUTIONS 5
1-3 START TO ASSEMBLY YOUR SYSTEM UNIT 6
1-4 INSTALLATION OF SLIM HDD 7
1-5 INSTALLATION OF SLIM FDD 1.44 MB 8
1-6 INSTALLATION OF SMART CARD READER 9
1-7 INSTALLATION OF CPU 10
1-8 INSTALLATION OF MEMORY 11
CHAPTER 2 SMART CARD SETUP 12
2-1 SOFTWARE DRIVER INSTALL 12
2-2 OPERATION SEQUENCE 14
1
Chapter 1 System Configuration
1-1System General Information
The Rear Panel
(1). Power inlet
(2). COM1 port
(3). PS/2 Mouse connector
(4). PS/2 Keyboard connector
(5). Ethernet RJ-45 connector
(6). Parallel port
(7). USB port
(8). VGA connector
(9). COM2 port

2
The Front Panel
(1). USB
(2). USB
(3). MIC
(4). Line in
(5). Line out
<1> ESLOT BOARD
3
<2> FRONT PANEL BOAR
D(TCP)
<3> COMPACT FLASH ADAPTER
(TCC)
Top site
Bottom site

4
(5) SMART Card Reader CONNECTOR
Motherboard: CON1
Reader: J1
Pin# Assignment
1RX
2CTS
3TXD
4RTS
5GND
6Reader On
7CTRL
8VCC5VSB
9GND
Pin# Assignment
1Receive data
2 Clear to send
3
Transmit data
4 Request to send
5GND
6 Reader on
7Card CTRL
8VCC5VSB
9GND
5
1-2Precautions
Electrostatic discharge (ESD) can easily damage your motherboard.
Observing a few basic precautions can help you safeguard against damage
that could result in expensive repairs. Follow the measures below to protect
your equipment from static discharge:
** Keep the Motherboard and other system components in their anti-static
packaging until you are ready to install them.
** Touch a grounded surface before you remove any system component
from its protective anti
-
static packaging. A grounded surface within easy
reach is the expansion slot covers at the rear of the system case or any
other unpainted portion of the system chassis.
** During configuration and installation, touch a grounded surface frequently
to discharge any static ele
ctric charge that may build up in your body.
Another option is to wear a grounding wrist strap.
** When handling a motherboard or an adapter card, avoid touching its
components. Handle the m
otherboard and adapter cards either by the
edges or by the mounting bracket that attaches to the slot opening in the
case.
Battery Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

6
1-3Start to Assembly Your System Unit
Before assembling your system unit, two steps have to be followed:
Remove •~ƒscrews
Uncover the case from the system unit
7
1-4Installation of Slim HDD
Follow these steps to install the slim HDD
1. Remove the screw from the tray
2. Push the slim HDD trayback to remove it
3. Put slim HDD on the tray
4. Insert the four screws and fully tighten with a suitable screwdriver
5. Pick the HDD cable from the packing bag
6. Insert one head with 44 pin to the slim HDD, the other one with 40 pin
to motherboard IDE1 and match two HDD power connectors together

10
1-7Installation of CPU
Follow these steps to install the CPU
1. Repeat steps 1 to 3 in 1-5 for removing the trays and ESLOT card
Read the ESD Precautions before you
unpack and install the CPU.
Make sure that the system power is off
before you install any component.
2. Pull up the CPU socket lever. See step 1 in illustration
3. Insert the CPU into the socket. Make sure that pin 1 of the CPU
matches the hole-1 of socket
4. Pull down the socket lever to lock the CPU into the socket. See step 2
11
1-8Installation of Memory
Follow these steps to install Memory
1. Repeat steps 1 and 2 in 1-4 for removing the slim HDD tray
Read the ESD Precautions before you
unpack and install the Memory.
Make sure that the system power is off
before you install any component.
2. Before inserting the DIMM, make sure the pin1 of the DIMM matches
with the pin1 on the DIMM socket
3. Insert DIMM into the DIMM sockets at a 90-degree angle and press
down

12
Chapter 2 Smart Card Setup
2-1Software Driver Install
(1) Enter the IC-Card subdirectory and double-click Setup.exe
(2) Click “OK”at the Welcome screen
(3) Click “Setup button”to install User Card Management software.
13
(4) Click “Continue”at the Choose Program Group.
(5) The driver files will now be installed. When finished installing, click the
“OK”to complete your installation.

14
2-2Operation Sequence
The purpose of this form is to modify User Card management.
First, set the port, then, input personal information, change User card
key and exit.
(1) Set COM Port
(2) Setting COM Port
Set COM port which the user
writes/reads. Click here into
setting COM port.
Select “com1”or “com2”, press
“Ok”to confirm COM port or
press “cancel”to reset.
15
(3) Test COM Port
(4) Input Personal Information
Press “OK”button to test port,
if successes, return message
“Port number set OK!”go on
step (4). Otherwise return
message “Error!”you must
reset COM port and test again,
that means repeat step 2 and
step 3 until success.
The card will store some
message of the card user.
Click here to input it.
OK

16
(5) Enter Personal Information
(6) Test Personal Information
Please enter the
personal information,
name, address, ID and
sex into the text box.
Press “Write”button. Return
message “finish!”Then, you
can “confirm”it.
OK
Tom
Room 2524, GuoMao Building RenMin
South Road, Shenzhen
00001
Note: Name maximum length is 8
characters. Address maximum
length is 132 characters. ID
maximum length is 15 characters.
17
(7) Read Your Personal Information
(8) Change Personal Information
Press this “Read”button, then
you can read “Personal
Information”you’ve written now.
Press this “Edit”button, then
you can read/change
“Personal Information”as you
like now.
Tom
Room 2524, GuoMao Building RenMin
South Road, Shenzhen
00001