Brightwell Quantura Q10+ User manual

Quantura Q10+ Laundry Dosing System
Safety Notes
IMPORTANT:
Please read the following precautions
carefully before using this equipment.
This appliance can be used by children age from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintanence shall not be made by children
without supervision.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid hazard.
Before Installation
Ensure you have checked all parts required are
present and inspect for any damage before
installation. In the unlikely event your items are
faulty, DO NOT install faulty or damaged parts as this
unsafe and will void any warranty. Please return to
your distributor in the original delivery condition
including any packaging. This unit is ONLY to be
installed by a suitably qualified person complying
with local regulations.
Quantura
Q10+
Peristaltic
tubing
× 1
(Silicone 5mm )
Ceramic weight
and foot filter
× 1
Remote dose
controller x1
PVC Tubing
1 x 3m (10ft)
Fixings Pack:
Screws × 2
Wall plugs ×2
Installation
Mounting and connection
Step 1: Using the wall plugs and screws
specified for this unit, fix the mounting
bracket to the wall. There is an embedded
spirit level to aid with this part of the
installation.
Step 2: Mount the unit to the wall by
hooking it onto the wall bracket. As you push
the unit down you should hear a click sound.
Step 3: Ensure there is no power to the
unit Remove front cover by turning thumb
screw anti-clockwise and pulling the front
cover towards you as shown.
Step 4: Insert one end of the tube ensuring
that it is slotted into the body of the
enclosure as shown.
INFORMATION: Silicone grease provided
must be applied to the tube and the pump &
rotor assembly before the tube is inserted.
Failure to apply the grease will affect the
pump performance during operation.
Step 5: Now by manually rotating the
pump head, feed the tube into the unit as
shown.
IMPORTANT to aid prolonging tube life and
efficent running, please use the Silicone
Grease (supplied) on the outer of the tube.
Spread liberally to the outside of the tube to
help ease installation, this will also aid
continuous smooth operation and help
prevent any potential snagging.
Step 6: Now insert the other end of the
tube ensuring that it is slotted into the body
of the enclosure as shown.
IMPORTANT INFORMATION: Brightwell
Dispensers Ltd (manufacturer) accepts no
responsibility and/or damages caused to
either the product or premises if the
installation process is not complied with in
full.
.
Connecting Chemicals
Step 1: Ensure there is no
power to the unit, push the tube
adaptors into the clamps nuts.
Then tighten the clamp nuts.
Step 2: Connect the suction
tube from the chemical
container to (A). Now connect
the delivery tube from (B) to the
injection point.
Power Supply
Should the supply cord be damaged, it should be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
Connecting or Replacing Handset
Step 1: Offer up the connector
handset to the connector of the
unit (positioned underneath the
pump). Make sure the connector
is lined up correctly as it will only
fit in a certain position.
Step 2: Tighten the connector by
turning it clockwise until finger
tight.
Note: Do not overtighten
.
This unit contains high voltage
circuitsthatmayexposeyoutothe
dangerofelectricshock.
Means for disconnectionmust be
incorporatedin accordancewith the
wiring rules.
Do not open the enclosurewithout
isolating the signal and supply
sources. Ensurethatthesesources
have beenisolatedforatleast5
minutesbeforeenteringthe
enclosure.
Do not powertheunitoutsideofthe
valuesstatedontheratinglabel.
Do not usedamagedorfrayed
cables.
Do not dismantleormodifythis
equipment.
Never insert fingers into mechanisms
without turning the power supply off
first.
Do not mounttheunittounstable,
irregularornon-verticalsurfaces.
Do not placeheavyobjectsontopof
theunit.
Do not attempttoplaceitems(suchas
screwdrivers)intothemovingpartsof
thepump head.
Always ensurethatcareistaken
whenhandlingchemicals.
Do not discard of the manual, this
must be retained.
This unit must be installed by suitably qualified
personnel in accordance with local regulations,
or in the absence of local regulations, installed
in accordance with the applicable
requirements in the National Electrical Code,
NFPA 70, Canadian Electrical Code (CEC),
Part 1, CSA C22.1, and Standard for
Ventilation Control and Fire Protection of
Commercial Cooking Operations, NFPA 96.
A
B
Wire Colours
ROW
US
Blue
Black
Brown
White

Initial Set up - Programming
Operating Instructions
Service Intervals
Selecting between Learn
Mode and Run mode
Remove the dust cover with a
screw driver. Use the screwdriver
to flick the switch Left for Learn
Mode and Right for Run mode
(normal operating mode).
IMPORTANT –The switch must be
in the Left position on the first
power up.
1. Pump Tube Servicing: It is recommended the pump tubes are inspected for
performance once every 3 months and lubricated with silicone grease to pro long
tube life.
2. Pump Calibration: As a guide once every 3 months it is recommended the flow
produced is checked to ensure consistent flow over the life of the tube. To do this run
the pump for minute and capture the flow produced. Compare this figure with the run
time of the pump to ensure the correct dosage is produced.
3. Pump Tube replacement: As a guide it is recommended the tube is replaced for a
new piece once every 6 months, or as needed.
Learn mode (Switch in left position)
Selecting a full dose of chemical
Pressing the top button indicated with a symbol will
activate the full dose of chemical. When pressed the
LED next to this button will turn solid Green to
demonstrate the command has been accepted. If a
delay has been set the LED will flash, showing it has
been activated, but in the delay period. Once the dose is
complete the RED LED shown below will switch on to
demonstrate the unit is currently locked out until the
Lock out time has elapsed.
Power up the unit. All the LEDS will briefly light up and then the Blue LED
will flash indicating that the unit is in LEARN MODE.
Optional Feature –Disable Prime mode
It is possible to disable the prime mode feature to prevent unwanted miss use of the
system. (feature only available in run mode)
Step 1: Potentiometer A–Adjust
A to set the initial delay time
between 0 & 20 minutes. All the
way to the left = 0 Minute.
The initial delay is the period of time
the pump will pause after the
activation button has been pressed
to allow for the machine to fill.
Step 2: Potentiometer B–Used
to adjust the Lockout period after
Pump has run (2-60 Minutes).
Lock out time is a period of time
the pump will not be usable, after it
has dosed chemical to prevent
multiple dosing.
Step 1: Hold down all three buttons at the same time
until the Prime indicator lights solid Blue (5 seconds)
Pump Speed
Press and hold the Prime (bottom)
button to adjust the pump speed.
The pump speed will reduce in 10%
increments down to 50% speed and
when you release the button the
speed will be set.
*If this section is skipped the pump
will run at 100% speed.
Full Dose
Press and release (for 0.5
seconds) the Full load (Top)
button. The pump will start running
and the Green LED will flash. Each
flash indicates 1 second of run
time. When the desired run time is
achieved, press and release (for
+/- 0.5 seconds) the Full load
button again. Maximum run time is
3 minutes.
Selecting a half dose of chemical
Pressing the middle button indicated with a symbol
will activate a half dose of chemical. When pressed the
LED next to the button will turn solid Amber to
demonstrate the command has been accepted. If a
delay has been set the LED will flash, showing it has
been activated, but in the delay period. Once the dose is
complete the RED LED shown below will switch on to
demonstrate the unit is currently locked out until the
Lock out time has elapsed.
Step 2: When the Blue indicator is on press the
Prime button until the RED lock out indicator turns
ON.
Prime mode is now disabled
Half Dose
Press and release (for 0.5 seconds)
the Half load (Middle) button. The
pump will start running and the
Yellow LED will flash. Each flash
indicates 1 second of run time.
When the desired run time is
achieved, press and release (for +/-
0.5 seconds) the Full load button
again. *if this section is skipped it
will be set as a 0 run time.
Please note.
Should you make an error in any of
these settings, just repeat the
procedure of the individual setting.
RUN MODE.
Move the switch to the right hand
side to enter Run mode. The unit
will now be ready to use.
Priming the pump
To prime the system, press and hold the bottom button
for 2 seconds. The LED will turn solid Blue and the
pump will run for the duration the button is held for.
Once the button is released the pump will exit prime
mode.
To reinstate Prime mode
Step 1: Hold down all three buttons at the same time until the Prime indicator turns solid
Blue.
Step 2: Press and hold the Prime button until the Green LED turns solid green.
Prime mode is now reinstated
WEEE Directive
Please remember to respect the local regulations: hand in the non-working
electrical equipment’s to an appropriate waste disposal centre. The packaging material
is recyclable. Dispose of the packaging in an environmentally friendly manner and
make it available for the recyclable material collection-service.
Flowrate –140ml/min (4.7 fl.oz/min)
NOTE:Flowrates measured with water, Suction length of 2 metres
The pump has a maximum run time of 3 minutes per
event. The pump cannot be programed to run longer
than this per event.
Dust Cover
B
A