Brizo BELO 63952LF User manual

77522 Rev. H
PULL-DOWN KITCHEN
AND BAR / PREP FAUCETS
T
E
F
L
O
N
Write purchased model number here.
BELO
®
Models
63052LF & 63952LF
1
For easy installation of your Brizo®
faucet you will need:
• To READ ALL the instructions
completely before beginning.
• To READ ALL warnings, care, and
maintenance information.
You may need the following tools:
WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE DISHWASHERS!
T
E
F
L
O
N
10/22/2019
1/8"

77522 Rev. H 2
TABLE OF CONTENTS:
Warranty ------------------------------------------------------------- Page 2
Installation Instructions ----------------------------------------------- Pages 3-13
Plastic Sleeve Installation --------------------------------------------- Page 11
Setting The Handle Limit Stop ----------------------------------------- Page 14
Maintenance -------------------------------------------------------- Page 15
Replacement Parts
To access additonal technical documents & product info, visit www.brizo.com/Your-Model-Number-Here
(example: www.brizo.com/9159T-DST)
www.brizo.com
1-877-345-BRIZO (2749)
[email protected]
?
Parts and Finish
All parts (other than electronic parts and batteries) and nishes of this Brizo® faucet are warranted to the original consumer purchaser to be free
from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was rst installed or,
for commercial users, the warranty period is ten (10) years for multi-family residential (apartments and condominiums and ve (5) years for all other
commercial uses, in each case from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Brizo® faucet are warranted to the original consumer purchaser to be free from defects in material
and workmanship for ve (5) years from the date of purchase or, for commercial users, for one (1) year from the date of purchase. No warranty is
provided on batteries.
What We Will Do
Brizo Kitchen & Bath Company will repair or replace, free of charge, during the applicable warranty period (as described above), any part or nish that
proves defective in material and/or workmanship under normal installation, use and service. If repair or replacement is not practical, Brizo Kitchen &
Bath Company may elect to refund the purchase price in exchange for the return of the product. These are your exclusive remedies.
What Is Not Covered
Any labor charges incurred by the purchaser to repair, replace, install or remove this product are not covered by this warranty. Brizo Kitchen & Bath
Company shall not be liable for any damage to the product resulting from reasonable wear and tear, outdoor use, misuse (including use of the product
for an unintended application), freezing water, abuse, neglect or improper or incorrectly performed installation, maintenance or repair, including failure
to follow the applicable care and cleaning instructions. Brizo Kitchen & Bath Company recommends using a professional plumber for all installation and
repair of faucets. We also recommend that you use only genuine Brizo® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts
A warranty claim may be made and replacement parts may be obtained by calling 1-877-345-BRIZO (2749) or by contacting us by mail or online as
follows (please include your model number and date of purchase):
In the United States and Mexico: In Canada:
Brizo Kitchen & Bath Company Masco Canada Limited, Plumbin Group
Brizo Customer Solutions Technical Service Centre
55 E. 111th Street 350 South Edgeware Road
Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us https://www.brizo.com/customer-support/contact-us
Proof of purchase (original sales receipt) from the original purchaser must be made available to Brizo Kitchen & Bath Company for all warranty claims
unless the purchaser has registered the product with Brizo Kitchen & Bath Company. This warranty applies only to Brizo® faucets installed in the United
States of America, Canada and Mexico.
Limitation on Duration of Implied Warranties. TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURA-
TION OF THIS WARRANTY, WHICHEVER IS SHORTER. Some states/provinces do not allow limitations on how long an implied warranty lasts, so
this limitation may not apply to you.
Limitation of Special, Incidental or Consequential Damages. BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, IN-
CIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT),
WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. BRIZO
KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY DAMAGE TO THE FAUCET RESULTING FROM REASONABLE WEAR AND
TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING WATER, ABUSE, NE-
GLECT OR IMPROPER OR INCORRECTLY PERFORMED INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING FAILURE TO FOLLOW THE
APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Some states/provinces do not allow the exclusion or limitation of special,
incidental or consequential damages, so the above limitations and exclusions may not apply to you. Notice to residents of the State of New Jersey:
The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey.
Additional Rights
This warranty gives you special legal rights, and you may also have other rights which vary from state/province to state/province.
This is Brizo Kitchen & Bath Company’s exclusive written warranty and the warranty is not transferable.
If you have any questions or concerns regarding our warranty, please contact us as provided above or visit our website at www.brizo.com.
Limited Warranty on Brizo®Faucets
© 2018 Masco Corporation of Indiana

77522 Rev. H
A. C.
A. Thread hose (1) into spray wand (2). C. Insert hose (1) into and through spout
sub-assembly (2).
3
1
2
1
Hose Installation
1
2
B.
B. To allow for easier assembly, bend
hose near wand as shown.
Bend

77522 Rev. H
A.
A. Verify friction washer (1), spout clip (2) and spout ring (3) are present on
spout assembly.
4
2
Spout Assembly
1
3
2

77522 Rev. H
B. C.
B. Insert hose (1) through guide in hub
and out through mounting shank
(2).
C. Align button (1) on spout clip with hole
in hub (2), then insert spout into hub.
Use back-and-forth motion to insert
spout assembly into hub until clip
button slips into hole. Rotate spout
assembly to ensure smooth
operation. USE CAUTION NOT TO
PINCH FINGERS.
5
Spout Assembly (Continuation)
1
2
1
2

77522 Rev. H
A. B.
A. Remove adhesive backing on trim
ring gasket (1) and press into place
on trim ring (2). Place trim ring on
bottom of spout hub. Insert supply
tubes through mounting hole in sink.
Your faucet is designed for a hole
diameter of 1 3/8" +/- 1/4" (35 mm
+/- 6 mm) and a deck thickness of
up to 3" (76 mm). Maximum deck
thickness of soap dispenser is
3" (76 mm).
B. Push hose (1) partially up into mounting
shank (2). Install the mounting bracket
(3) and nut (4) onto the mounting shank
using wrench (5). Note 1: The wrench
provided is designed to be used
with a variety of tools: flat/Phillips
head screwdrivers, wrenches, etc.
Note 2: For thin gauge sinks (not
recommended), use the thin deck aid
(6) RP37490 (not included) as shown
for single and 3 hole installations
to help support the deck. HINT: Turn
the spout tube opposite the handle to
balance the assembly when mounting.
6
3
Faucet Installation - Center Mount
1
2
3
2
4
1
5
6

77522 Rev. H
Optional
For optional installations using the 10"
escutcheon, order RP49588 (specify finish)
not supplied. Replace the trim ring with the
10" escutcheon (1) and gasket (2). Push
hose (3) partially up into mounting shank.
Mount as shown above using the
two 1/4-20 studs (4), nuts and washers
(5), bracket (6) with nut and wrench (7).
The wrench provided is designed to
be used with a variety of tools:
flat/Phillips head screwdrivers,
wrenches, etc.
4
Optional Escutcheon Installation
1
2
4
5
4
5
6
7
3
7

77522 Rev. H 8
5
1. Insert ferrule (1) into cold water stop.
2. Thread on check valve (2) and tighten (do not overtighten).
Continue instructions on page 2.
Important:To ensure proper operation of your plumbing it is essential to
install these check valve assemblies onto your supplystops.
1
1. Introduzca el casquillo (1) en el tope del agua fría.
2. Enrosque la válvula de cheque (2) y apriete (no apriete demasiado).
Continúe las instrucciones en la página 2.
Importante:Para asegurar el funcionamientodebidode su plomería esesencialin-
stalar estos ensambles de válvulas checadoras en los topesdel suministro deagua.
1. Introduisez la virole(1) dans le robinetd’alimentationen eau froide.
2. Vissez le clapet non-retour (2) et serrez-le (prenez garde de trop serrer).
Continuez les instructions à la page 2.
Important :Vous devez installer ces clapets de non-retour sur vos robinets
d’alimentation pour que la plomberie fonctionne correctement.
CheckValve Installation
Instalación de la VálvulaChecadora
Installation du clapet de non-retour
2
6/5/08 53442 Rev B
1
A. For this step, use the parts shown above.
A.
Notice
Property damage and water leak possible. Incorrectly installed or unapproved check
valve assemblies may cause water leaks and property damage. Follow instructions to
install check valve assemblies provided with this faucet.
B.
C.
1
2
B. Important: To ensure proper operation of your plumbing it is essential to
install these check valve assemblies onto your supply stops. Insert ferrule (1)
into cold water stop.
C. Thread on check valve (2) and tighten. DO NOT OVERTIGHTEN. Repeat steps B
& C for hot water stop.
REQUIRED FOR MODEL 63052LF ONLY

77522 Rev. H 9
3
2
B.
1
A.
4
2
1
3
OR
O
OU
NOTICE
If you determine the PEX supply tubing for this faucet is too
long and must be shorter to create an acceptable installation,
be sure to read the instructions and plan ahead. When cutting
the supply tubing the installer accepts the responsibility to do
so in a way that allows a leak-free joint to be created. Delta is
not responsible for tubing that is cut too short or cut in a way
that will not allow for a leak-free joint. DO NOT use a metal
sleeve (ferrule) or gasket (supplied with faucet) in place of the
plastic sleeve (ferrule) supplied, it may not create a leak-free
joint. Do not use pipe dope or other sealants on water line
connections.
Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too
long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) to supply valve connection (4).
Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other tube. Turn on water,
examine for leaks.
Standard Connections
NOTICE
To avoid risk of property damage, Follow
instructions for proper installation. Failure to
follow these instructions may result in risk
of property damage caused by leaking at this
connection. Do not use pipe dope or other
sealants on water line connections.
Custom Fit Connections
A.
B.
For custom fit installations, you must use plastic sleeves (ferrules) supplied with model and nuts included on
supply lines. Tube cut must be straight. See plastic sleeve (ferrule) installation instructions found in and
included in this document for more information.
Slide nut (1) over plastic sleeve (ferrule) (3). Start nut by hand onto supply valve connection (2) to prevent
cross-threading. Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other
supply line. Turn on water, examine for leaks.
Potential Problems and Remedies
Tubing is not cut perpendicular to the axis of the tube: carefully make an additional cut, being careful not to
cut the tube too short.
Tubing is cut too short: buy a coupling union and a replacement supply line that mate together from a store.
The coupling union end intended to connect to the faucet must mate to the standard 3/8" connection nuts and
plastic sleeves (ferrules) supplied with the faucet.
The plastic sleeve (ferrule) or connection nut is lost: purchase a replacement nut and/or plastic sleeve
(ferrule) that are designed to seal with PEX tubing.

77522 Rev. H
A.
A. Place bucket under faucet quick connect fitting (1), open both supply valves (2) and
turn faucet valve on by operating handle (3) for one minute. Important: This flushes
away any debris that could cause damage to internal components. When
complete, close both supply valves and turn faucet valve off to shut off water flow.
2
2
1
6
3
10

77522 Rev. H 11
1. Identify desired length of tube (1). Leave 1" - 2"
of extra length to allow for easier installation and
cut tube. Ensure cut is straight and burr free.
2. Slide nut (2) and plastic sleeve (3) onto cut tube.
Ensure sleeve is oriented as shown.
3. Insert tube into outlet tting (4). Tube should
touch bottom of hole inside tting.
4. Slide plastic sleeve down tube until it engages
top of tting. WARNING: Failure to use plastic
sleeve in the correct orientation will result in
disconnection and possible water damage.
5. Slide nut over plastic sleeve. With wrench,
tighten nut 2 turns past nger tight.
Custom Fit Connections - Plastic Sleeve Installation Instructions
Correct method
3
2
1
4
Ensure cut is straight.
Do not install sleeve
upside down.
Ensure tube is fully
inserted into stop
before sliding sleeve
down to engage top
of tting.
Incorrect Installation
Do not use RP51243
gasket (1) supplied
with PEX tubing or
brass ferrule (2)
supplied with
valve stops.
1
2
Failure to use plastic sleeve (ferrule) in
the correct orientation will result in
disconnection and possible water dam-
age.
NOTICE

77522 Rev. H 12
B.
D.
A. Insert hose end (1) through hose
weight assembly (2).
B. Insert check-valve adapter (1) into
pull-out hose fitting (2). Ensure
weight does not slide off hose.
C. Insert faucet outlet quick connect fitting
(1) into adapter.
D. Rotate arms of adapter (1) to secure
assembly to pull-out hose and faucet
outlet tube.
7
C.
Sprayer Hose Connections
2
1
1
1
1
A.
D.
1
2

77522 Rev. H 13
8
Faucet Inspection and Operation
3
2
1
1
A.
Unlock
Lock
A. Turn on hot and cold water supplies
(1). Pull the hose assembly (2) out of
the spout. Be sure to hold the end of
the sprayer down into the sink and turn
faucet handle (3) to the mixed position
for one minute. Check all connections at
arrows for leaks. Re-tighten if necessary,
but do not overtighten.
B. Sprayer will lock into position when
brought into proximity of the spout
magnet. The sprayer can be removed
by either pulling directly out from the
spout or by twisting 90° in either
direction which will cause the magnets
to repel and the head to decouple from
the spout (recommended). Check the
operation of the sprayer by operating the
trigger (4) from aerator to spray. The
diverter will remain in the last diverted
mode. To reduce or pause ow, push
selector button further into wand. The
bar/prep faucet is a two function sprayer
only. Press button (5) to choose
between modes.
4
5
B.
OR

77522 Rev. H 14
This faucet includes an integrated
handle limit stop that has two positions.
Position 1, to the left, allows full handle
motion (the full range between “all cold”
to “all hot”). The faucet is set in position
1 in the factory. Position 2, to the right,
allows half of the normal handle motion
(“all cold” to “mixed hot/cold”).
The handle limit stop can be adjusted
by the homeowner once the faucet is
installed. Setting the handle limit stop in
position 2 may help to prevent scalding
Setting The Handle Limit Stop (Optional)
12
because it limits the amount of hot water
in the mix; however, this handle limit stop will
not always prevent scalding because it does
not compensate for incoming pressure or
sudden water temperature changes.
To change positions of the handle limit
stop: remove the handle; move the
valve stem to the all cold position so the
water is on; change the position of the
handle limit stop; turn off the water; reinstall
the handle.
9

77522 Rev. H
T
E
F
L
O
N
15
If faucet leaks from under handle:
Remove handle and ensure cap (1) is tight.
Use adjustable wrench on flats of cap (2) to
tighten cap.
If leak persists–SHUT OFF WATER
SUPPLIES. Replace valve cartridge (3).
If faucet leaks from spout outlet–SHUT
OFF WATER SUPPLIES. Replace valve
cartridge (3).
Maintenance
Your Brizo®Faucet pull-down spout
incorporates a backow protection system
that has been tested to be in compliance
with ASME A112.18.3 and
ASME A112.18.1 / CSA B125.1. It
incorporates two certied check valves in
series, which operate independently.
Backow Protection System
Note: A small amount of water may run
out the spout or drip for a very short
period after the faucet is shut off. This is
a natural occurrence caused by the long
exible hose.
3
1
Cleaning And Care
Care should be given to the cleaning
of this product. Although its finish is
extremely durable, it can be damaged
by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and
blot dry with a soft towel.
2

77522 Rev. H 16

77522 Rev. H
LLAVES DE AGUA/GRIFOS
DE CAÑO EXTRAÍBLE
PARA COCINAS Y BARES /
MULTI-PROPÓSITO
Escriba aquí el número del modelo comprado.
BELO
®
Modelos
63052LF y 63952LF
1
Para instalación fácil de su llave
Brizo®usted necesitará:
• LEER TODAS las instrucciones
completamente antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
Usted puede necesitar:
ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR CON MAQUINAS
LAVAPLATOS PORTATILES!
T
E
F
L
O
N
10/22/2019
T
E
F
L
O
N
1/8"

77522 Rev. H 2
Índice:
Garantía ------------------------------------------------------------ Página 2
Instrucciones para la Instalación -------------------------------------- Páginas 3-14
Instalación de la Manga Plástica -------------------------------------- Página 11
Fijando la parada de límite de la manija -------------------------------- Página 14
Mantenimiento ------------------------------------------------------ Página 15
Piezas de Repuesto
www.brizo.com
1-877-345-BRIZO (2749)
[email protected]
?
Para acceder a documentos técnicos adicionales e información sobre el producto, visítenos en www.
brizo.com/p/Your-Model-Number-Here (ejemplo: www.brizo.com/9159T-DST)
Piezas y Acabado
Todas las piezas (excepto los componentes electrónicos y las pilas) y acabados de esta llave de agua/grifo Brizo® están garantizados al consumidor comprador
original de estar libres de defectos en material y fabricación durante el tiempo que el comprador original sea propietario de la vivienda en la que la llave de agua
fue originalmente instalada o, para usuarios comerciales, el período de garantía es de diez (10) años para viviendas multifamiliares (apartamentos y condominios
y cinco (5) años para todos los demás usos comerciales, en cada caso desde la fecha de compra.
Piezas electrónicas y pilas (si aplicable)
Las piezas electrónicas (excepto las pilas), si las hay, de esta llave de agua/grifo Brizo® están garantizadas al consumidor comprador original de estar libres de
defectos en material y fabricación durante cinco (5) años a partir de la fecha de compra en el caso de los consumidores comerciales, durante un (1) año a partir
de la fecha de compra.
No ofrecemos garantía en la pilas.
Lo que haremos
La compañía Brizo Kitchen & Bath Company reparará o reemplazará, sin costo alguno, durante el periodo de garantía aplicable (como descrito arriba) cualquier
pieza o acabado que demuestre estar defectuosa en material y/o mano de obra bajo la instalación, el uso y el servicio normal. Si la reparación o el reemplazo no
es práctico, Brizo Kitchen & Bath Company puede optar por reembolsarle el precio de compra a cambio de la devolución del producto. Estos son sus remedios
exclusivos.
Lo que no está cubierto
Esta garantía no cubre los costos de mano de obra incurridos por el comprador para reparar, reemplazar, instalar o desmontar este producto. Brizo Kitchen & Bath
Company no será responsable por cualquier daño al grifo que resulte del desgaste razonable, uso en el exterior de la propiedad, uso indebido (incluyendo el uso
del producto para una aplicación indebida), agua helada, abuso, negligencia, o instalación, mantenimiento o reparación realizadas incorrectamente, incluyendo el
no seguir las instrucciones correspondientes para el cuidado, la limpieza y el mantenimiento.
Brizo Kitchen & Bath Company recomienda que un plomero profesional haga toda la instalación y las reparaciones. También recomendamos que use solo piezas
de repuestos originales Brizo®.
Lo que usted debe hacer para obtener servicio de garantía o piezas de repuesto
Puede hacer un reclamo para la garantía y puede obtener piezas de repuesto llamando al 1-877-345-BRIZO (2749) o contactándonos por correo o en línea de la
siguiente manera (por favor incluya su número de modelo y fecha de compra):
En los Estados Unidos y México: En Canadá
Brizo Kitchen and Bath Company Masco Canada Limited, Groupe plomberie
Brizo Customer Solutions Centre de services techniques
55 E. 111th Street 350, chemin South Edgeware
Indianapolis, IN 46280 St. Thomas (Ontario) Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us https://www.brizo.com/customer-support/contact-us
El comprobante de compra (recibo de venta original) del comprador original debe estar disponible a Brizo Kitchen & Bath Company para todos los reclamos de
garantía a menos que el comprador haya registrado el producto con Brizo Kitchen & Bath Company. Esta garantía se aplica solo a las llaves de agua Brizo®
instaladas en los Estados Unidos de América, Canadá y México.
La limitación de la duración de las garantías implícitas.
HASTA EL ALCANCE EN QUE LA LEY LO PERMITA, CUALQUIER GARANTA IMPLCITA, INCLUIDAS LAS GARANTAS IMPLCITAS DE COMERCIABILIDAD
Y DE IDONEIDAD PARA UN PROPSITO PARTICULAR, EST LIMITADA AL PERODO LEGAL O A LA DURACIN DE ESTA GARANTA, LO QUE SEA MS
CORTO. Algunos estados/provincias no permiten la limitación de la duración de una garantía implícita por lo que limitación arriba puede no aplicarle.
Limitación de daños especiales, incidentales o consiguientes.
BRIZO KITCHEN & BATH COMPANY NO SER RESPONSABLE POR NINGN DAO ESPECIAL, INCIDENTAL O CONSIGUIENTE (INCLUYENDO LOS GAS-
TOS DE MANO DE OBRA PARA REPARAR, REEMPLAZAR, INSTALAR O DESMONTAR ESTE PRODUCTO), YA SEA RESULTADO DEL INCUMPLIMIENTO DE
CUALQUIER GARANTA EXPRESA O IMPLCITA, INCUMPLIMIENTO DE CONTRATO, AGRAVIO O DE OTRA MANERA. BRIZO KITCHEN & BATH COMPANY
NO SE RESPONSABILIZAR POR CUALQUIER DAO AL GRIFO QUE RESULTE DEL DESGASTE RAZONABLE, USO EN EL EXTERIOR DE LA PROPIEDAD,
USO INDEBIDO (INCLUYENDO EL USO DEL PRODUCTO PARA UNA APLICACIN NO INTENCIONADA), AGUA HELADA, ABUSO, NEGLIGENCIA O INSTA-
LACIN, MANTENIMIENTO O REPARACIN INADECUADA O INCORRECTA, INCLUYENDO EL NO SEGUIR LAS INSTRUCCIONES CORRESPONDIENTES
PARA LA INSTALACIN, EL CUIDADO, Y LA LIMPIEZA. Algunos estados/provincias no permiten la exclusión o limitación de daños especiales, incidentales o
consecuentes, por lo que estas limitaciones y exclusiones puedan no aplicarle. Aviso para los residentes del estado de New Jersey: Las disposiciones de este
documento tienen la intención de aplicarse en la máxima medida permitida por las leyes del estado de New Jersey.
Derechos adicionales
Esta garantía le otorga derechos legales especícos, y también puede tener otros derechos que varían de estado/provincia a estado/provincia.
Esta es la garantía escrita exclusiva de Brizo Kitchen & Bath Company y la garantía no es transferible.
Si tiene preguntas o dudas con respecto a nuestra garantía, por favor comuníquese con nosotros como se indica arriba o visite nuestro sitio web www.brizo.com.
© 2018 Masco Corporación de Indiana
Garantía en los grifos Brizo®

77522 Rev. H
A. C.
A. Enrosque la manguera (1) en el
mango del rociador (2).
C. Introduzca la manguera (1) en y a
través del sub-ensamble del
surtidor (2).
3
1
2
1
Instalación de la Manguera
1
2
B.
B. Para permitir un ensamble más
fácil,
doble la manguera cerca del mango
como se muestra.
Doble

77522 Rev. H
A. Verique si la arandela de fricción (1), gancho del surtidor (2) y el aro del surtidor
(3), están presentes en el ensamble del surtidor.
4
2
Ensamble de Surtidor
A.
1
3
2