Broadrack WP-919 User manual

WP Series
Wall-mount Panel
User Manual
Rev 1.0

WP series User Manual
I
Packing List
The complete package consist:
One wall-mount panel
One VGA cable
One USB A-A cable (touch screen only)
One DVI-D cable (optional)
One power cord
Driver CD (touch screen only)
Check to make sure that the unit was notdamaged in shipping. If you encounter a
problem, contact your dealer.
Please read this manual thoroughly, and follow the installation and operation
procedures carefully to prevent any damage to the product, and / or any of the
devices that connect to it.

WP series User Manual
II
Safety Instructions
1. Please read these safety instructions carefully.
2. Please keep this User’s Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning. Don’t use
liquid or sprayed detergent for cleaning. Use moisture sheet or clothe for
cleaning.
4. For pluggable equipment, the socked-outlet shall be installed near the
equipment and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when install. A drop orfall could cause
injury.
7. Do not leave this equipment in an environment unconditioned, storage
temperature above 600C, it may damage the equipment.
8. The opening on the enclosure is for air convection hence the equipment from
overheating. DO NOT COVER THE OPENING.
9. Make sure the voltage of the power sourceconnectthe equipment to the power
outlet.
10.Please keep the power cord such a waythat people can not step on it. Do not
place anything over power cord. The power cord must rate for the voltage and
current marked on the product’s electrical ratings label. The voltage and current
rating of the cord should be greaterthan the voltage and thecurrent rating
marked on the product.
11.All cautions and warning on the equipment should be noted.
12.If the equipmentis not in use for long time, disconnect the equipment from mains
to avoid being damaged bytransient over-voltage.
13.Never pour any liquid into ventilation openings; this could cause fire or electrical
shock.
14.Never open the equipment. Forsafety reason, qualified service personnel
should only open the equipment.
15.If one of the following situations arises, get the equipment checked byservice
personnel.
The Power Cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to
User’s Manual.

WP series User Manual
III
The equipment has dropped and damaged.
If the equipment has obvious signs or breakage.

WP series User Manual
IV
Index of Contents
Packing List......................................................................................................... I
Safety Instructions.............................................................................................. II
Index of Contents..............................................................................................IV
1. General Information..................................................................................... 2
1.1 Overview.............................................................................................. 2
1.2 Product Specification........................................................................... 3
1.2.1 WP-815 Specification..................................................................3
1.2.2 WP-817 Specification..................................................................5
1.2.3 WP-919 Specification..................................................................7
1.2.4 WP-920 Specification..................................................................9
2. Panel Controls and OSD Function............................................................. 11
2.1 Auto Tune.......................................................................................... 11
2.2 Input Source ...................................................................................... 11
2.3 Brightness.......................................................................................... 12
2.4 Contrast............................................................................................. 12
2.5 Color.................................................................................................. 13
2.6 Position.............................................................................................. 13
2.7 Language........................................................................................... 14
2.8 Recall................................................................................................. 15
2.9 Exit..................................................................................................... 15
2.10 Power Indicator................................................................................ 15
3. Touchscreen (option)................................................................................. 16
3.1 General Page..................................................................................... 17
3.2 Sound Page....................................................................................... 18
3.3 Mouse Page....................................................................................... 19
3.4 Multi-monitor Page............................................................................. 20
3.5 Advance Page ................................................................................... 21
4. Installation.................................................................................................. 23
4.1 Install Wall-mount Panel.................................................................... 23
4.1.1 Notes ........................................................................................ 23
4.1.2 Installation Steps: ......................................................................23
4.2 Installing the Video Card and Video Driver........................................... 25
4.2.1 Configuring the Display Settings............................................... 25
4.2.2 Connecting the Wall-mount Panel........................................... 26
4.3 Turning on the Wall-mount Panel ...................................................... 26

WP series User Manual
V
4.4 Testing the wall-mount Panel............................................................... 26

WP Series User Manual
2
1.General Information
1.1 Overview
WP series is designed to provide the industrial user with superior picture quality
and state-of-the-art features housed in a rugged industrial enclosure, which will
assure reliable operation in most harsh environments.
Support Sun native resolution (for 17 / 19 / 20.1”panel)
Bright Active Matrix TFT display
OSD function (On Screen Display) for LCD display
Panel protected by tempered glass
Touch screen function

WP Series User Manual
3
1.2 Product Specification
1.2.1 WP-815 Specification
Model name
WP-815
Dimension
482.6 x 354.6 x 64 mm / 19.0 x 14.0 x 2.5 inches
Package Dimension
566 x 484 x 245 mm / 22.3 x 19.1 x 9.6 inches
Net Weight
10.5 Kg / 23.1 lbs
Gross Weight
14.7 Kg / 32.4 lbs
Display Size
15 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum up to 1024 x 768 (XGA)
Pixel Pitch
Supports 0.297 mm x 0.297 mm
Viewing Angle (CR>10)
Right-Left View 130°(Typ)
Up-Down View 100°(Typ)
Contrast Ratio
550:1
Brightness
White 250 cd/m²(Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16M Colors (6-bit with FRC)
Response Time
Rising Time 2 ms, Decay Time 6 ms
Connectors
1 x VGA, 1 x AC Inlet, 1 x Power ON / OFF Switch, 1 x USB or 1 x
RS-232(touch screen only), 1 x DVI (optional)
Signal Cable
VGA cable or DVI-D, USB A-A or RS232 cable (touch screen only)
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
10.12W
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Touch Screen
5 wires resistive USB interface / RS232 interface
Table 1-1. WP-815 Specification

WP Series User Manual
4
Figure 1-1. WP-815 Dimension

WP Series User Manual
5
1.2.2 WP-817 Specification
Model name
WP-817
Dimension
482.6 x 354.6 x 64 mm / 19.0 x 14.0 x 2.5 inches
Package Dimension
566 x 484 x 245 mm / 22.3 x 19.1 x 9.6 inches
Net Weight
11.0 Kg / 24.3 lbs
Gross Weight
15.2 Kg / 33.5 lbs
Display Size
17 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1280 x 1024 (SXGA)
Pixel Pitch
Supports 0.264 mm x 0.264 mm
Viewing Angle (CR>10)
Right-Left view 170°(Typ)
Up-Down View 160°(Typ)
Contrast Ratio
1000:1
Brightness
White 250 cd/m²(Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16.7M Colors (6-bit with FRC)
Response Time
Rising Time 3.8 ms, Decay Time 1.2 ms
Connectors
1 x VGA, 1 x AC Inlet, 1 x Power ON / OFF Switch, 1 x USB or 1 x
RS-232(touch screen only), 1 x DVI (optional)
Signal Cable
VGA cable or DVI-D, USB A-A or RS232 cable (touch screen only)
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
9.91W
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Touch Screen
5 wires resistive USB interface / RS232 interface
Table 1-2. WP-817 Specification

WP Series User Manual
6
Figure 1-2. WP-817 Dimension

WP Series User Manual
7
1.2.3 WP-919 Specification
Model name
WP-919
Dimension
482.6 x 398.6 x 64 mm / 19.0 x 15.7 x 2.5 inches
Package Dimension
561 x 526 x 250 mm / 22.1 x 20.7 x 9.8 inches
Net Weight
9.0 Kg / 19.8 lbs
Gross Weight
12.0 Kg / 26.4 lbs
Display Size
19 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1280 x 1024 (SXGA)
Pixel Pitch
Supports 0.098 mm x 0.294 mm
Viewing Angle (CR>10)
Right-Left View 170°(Typ)
Up-Down View 160°(Typ)
Contrast Ratio
1000:1
Brightness
White 250 cd/m²(Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16.7M Colors (6-bit with FRC)
Response Time
Rising Time 3.6 ms, Decay Time 1.4 ms
Connectors
1 x VGA, 1 x AC Inlet, 1 x Power ON / OFF Switch, 1 x USB or 1 x
RS-232(touch screen only), 1 x DVI (optional)
Signal Cable
VGA cable or DVI-D, USB A-A or RS232 cable (touch screen only)
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
11.03W
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Touch Screen
5 wires resistive USB interface / RS232 interface
Table 1-3. WP-919 Specification

WP Series User Manual
8
Figure 1-3. WP-919 Dimension

WP Series User Manual
9
1.2.4 WP-920 Specification
Model name
WP-920
Dimension
482.6 x 398.6 x 64 mm / 19.0 x 15.7 x 2.5 inches
Package Dimension
561 x 526 x 250 mm / 22.1 x 20.7 x 9.8 inches
Net Weight
10.8 Kg / 23.8 lbs
Gross Weight
13.6 Kg / 29.9 lbs
Display Size
20.1 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1600 x 1200 (UXGA)
Pixel Pitch
Supports 0.255 mm x 0.255 mm
Active Display Area
Horizontal: 408.0 mm, Vertical: 306.0 mm
Viewing Angle (CR>10)
Right-Left view 178°(Typ)
Up-Down View 178°(Typ)
Contrast Ratio
1000 : 1
Brightness
White 300 cd/m²
Back Light
Six Lamps for Back Light
Supported Colors
16.7M Colors (8-bit with FRC)
Response Time
Rising Time 7 ms, Decay Time 9 ms
Connectors
1 x VGA, 1 x AC Inlet, 1 x Power ON / OFF Switch, 1 x USB or 1 x
RS-232(touch screen only), 1 x DVI (optional)
Signal Cable
VGA cable or DVI-D, USB A-A or RS232 cable (touch screen only)
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
45 W
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Touch Screen
5 wires resistive USB interface / RS232 interface
Table 1-4. WP-920 Specification

WP Series User Manual
10
Figure 1-4. WP-920 Dimension

WP Series User Manual
11
2.Panel Controls and OSD Function
Table 2-1. Panel Controls
Figure 2-1. WP Series OSD Control Bar
2.1 Auto Tune
Press the “auto tune” button. The panel will adjust the display size
automatically and also tune the panel to its best condition.
2.2 Input Source
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
Controls
Description
Soft power on / off button. Adjacent LED is lit when
on.
Auto
Auto-synchronize and scale down display to any
valid factory preset timings.
Press to scroll the function you want to adjust.
Press to scroll the function you want to adjust.
Menu
To access the main menu. This button also acts as
the “Enter” button.

WP Series User Manual
12
3. Press the“menu”button to enter,and you will see:
VGA / DVI
4. Use the “Down” and “Up” button to select the input source of signal.
5. Press the “menu” button to enter
2.3 Brightness
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the“menu”button to enter.
4. Use the“Down”and“Up”button to adjust the brightness of the display.
5. Press the “menu” button to enter.
2.4 Contrast
1.Press the “menu” button.
2.Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
1.Press the “menu” button to enter.
2.Use the “Down” and “Up” button to adjust the contrast of the display.

WP Series User Manual
13
3.Press the “menu” button to enter.
2.5 Color
1.Press the “menu” button.
2.Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3.Press the “menu” button to enter. And you will see:
Icon
Description
9300°K
To set CIE coordinates at 9300°K color
7500°K
To set CIE coordinates at 7500°K color
6500°K
To set CIE coordinates at 6500°K color
User
To set user defined CIE
Auto color
To auto adjust color
Return
To exit and return to the previous page
Table 2-2. Icon Description
4.Use the “Down” and “Up” button to adjust the color of the display.
5.Press “menu” to enter.
2.6 Position
1.Press the “menu” button.
2.Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness

WP Series User Manual
14
Contrast
Color
Position
Language
Recall
Exit
3.Press the “menu” button to enter. And you will see:
Icon
Description
Image Pos
To adjust the position of the image.
OSD Pos
To adjust the position of the OSD.
Return
To exit and return to the previous page
Table 2-3. Icon Description
4.Use the “Down” and “Up” button to scroll.
5.Press the “menu” button to enter.
2.7 Language
1.Press the “menu” button.
2.Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3.Press the “menu” button to enter. And you will see:
English
German
French
Italian
Spanish

WP Series User Manual
15
4.Use the “Down” and “Up” button to scroll.
5.Press the “menu” button to enter.
2.8 Recall
1.Press the “menu” button.
2.Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3.Press the “menu” button to enter, and you will see:
Yes/ No
4.Select “Yes” button then ‘Menu” button to recall the factory setting.
Select “No “ to return to the previous page.
2.9 Exit
Press the “exit” button to quit OSD menu.
2.10 Power Indicator
GREEN ON
RED STANDBY
RED SUSPEND
RED OFF
OSD –On Screen Display