Brother BAS-416 User manual

BAS-416
ENTERING DISK DATA & SETTING THE COLOR SEQUENCE
Insert floppy disk into disk drive
ENTER
ENTER
START
NEEDLE
SET
END
#
START
*
Press ENTER.
Press UP or DOWN arrows to scroll
the disk directory.
Press (*) key to read
the design name.
Press ENTER to copy the design to
the machine memory.
Press START to calculate design
size and number of color changes.
Press NEEDLE SET to enter
color programming mode.
Press UP or Down arrow keys to
assign needle number (Color).
Press FORWARD arrow to select
next color of design or BACK arrow
for previous color of design.
Press END to exit needle set mode.
Use ARROW keys to center your
design in the frame.
Press (#) key to trace the mask
(outside edge) of the design.
Press START to start sewing.
ENTER A DESIGN FROM EDITOR MODE
ENTER Press ENTER.
#
Press UP or DOWN arrows to begin
reading computer directory.
ENTER Press ENTER to copy the design to
the machine memory.
START Press START to calculate design
size and number of color changes.
ENTER A DESIGN FROM THE MACHINE MEMORY
ENTER
START Press START to calculate design
size and number of color changes.
Use BACK and FORWARD keys
to pick a design from memory.
Press ENTER to view design name
Press the (#) key until “EDITOR”
appears on the screen.
Program color sequence (see Step 8)
Use ARROW keys to center your design (see Step 12)
Press (#) key to trace the mask of the design (see Step 13)
Press START to start sewing (see Step 14)
Program color sequence (see Step 8)
Use ARROW keys to center your design (see Step 12)
Press (#) key to trace the mask of the design (see Step 13)
Press START to start sewing (see Step 14)
Press UP or DOWN arrow to begin
reading the disk.
Use BACK and FORWARD keys
to pick an empty memory location.
Use BACK and FORWARD keys
to pick an empty memory location.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
BAS-416,416A-Quick Reference Guide
BAS-416,416A-Quick Reference Guide
For Technical Assistance Please Call 1-877-4BROTHER
FO/SB - 2000/1 - 002

BAS-416
SETTING THE ROTATE, MIRROR, REPEAT
START
EDIT
Set STR_P. Co. # #
N_No. # # # # # # # # #
After loading your design and at the
display below, do the following.
EDIT
END
To enter EDIT mode.
To select which option you wish
to change.
To enter that options EDIT
values.
To change the values of the
option you choose
To EXIT the edit mode
To return to the above display
with changes in effect.
ERASING A STORED DESIGN FROM MEMORY
ENTER
CLEAR Press CLEAR to delete the design
from machine memory.
Use BACK and FORWARD keys
to pick a design from memory.
Press ENTER to view design name
END Press END to return to
“FileNo” screen
SETTING HOOP FEED POSITION
HOOP
FEED
HOOP
FEED
Press HOOP FEED to move the frame to
the current HOOP FEED position
If you wish to change the position
Use the ARROW keys to move the frame
to a new position
Press HOOP FEED to toggle between
sewing position and hoop feed position
ENTER Press ENTER to store the new HOOP
FEED position
MOVING THE NEEDLE CASE
NEEDLE
SELECT
END
To enter the NEEDLE
SELECT mode
To move the needle case left
and right.
To EXIT the NEEDLE SELECT
mode
ERASE ALL DESIGNS / HARD RESET
Turn the power OFF on the machine.
Press and HOLD the DOWN ARROW
button while turning the power ON
CLEAR When asked “Do you want to clear?”
Press the CLEAR key.
The machine will continue the power up sequence.
“FLOATING” THROUGH A DESIGN
R_St: # # # # # # # # # Co. # #
N_No. # # # # # # # #
To move through a design after you have started
sewing you must first STOP the machine.
#Press “#” to display a “J” in the gray
box
To move by 100 stitches either
FORWARD or BACK in design
#Press “#” again to display a “C” in
the gray box
To move by color changes either
FORWARD or BACK in design
#Press “#” again to display a “T” in
the gray box
To move BACK only to the first stitch
of the design
#Press “#” To display a “I” in the gray
box
To move the frame in small increments
to correct registration
FO/SB - 2000/1 - 002