BUDDEE BD903001-BK User manual

METALLIC BLUETOOTH®SPEAKER
WITH DUAL STEREO SPEAKERS
USER MANUAL
Thank you for purchasing a Buddee Metallic Bluetooth®
Speaker. For optimum performance and safety, read these
instructions carefully before connecting, operating or adjusting
this product. Refer to this manual for future reference.
INTRODUCTION
Play music wirelessly, listen to FM radio or talk clearly on the
phone with the Buddee Metallic Bluetooth® Speaker. In a
compact and stylish design, this speaker delivers high quality
stereo sound.
Charge your speaker from any USB compatible device. Works
with all Bluetooth® enabled devices
up to 10m or play your tunes via the auxiliary port or TF card
slot.
FEATURES
• Bluetooth®audio
• USB charging
• AUX input
• Answer phone calls
• 10m wireless range
• TF card playback
• FM radio
• Dual speakers
PACKAGE CONTENTS
Before attempting to use this unit, please check the
packaging and make sure the following items are contained
in the shipping carton:
• Metallic Bluetooth®Speaker
• Micro-USB charging cable
• 3.5mm AUX cable
• User manual
CHARGING
1. Insert the micro-USB end of the included cable into the
charging port on the back of the Metallic Speaker.
2. Insert the USB end into a powered USB source such as a
computer, laptop or USB wall charger. The charging indicator
will light up red.
NOTE: Please fully charge the Metallic Speaker prior to first
use.
POWERING ON
1. Slide the power switch to the ON position and the display
will light up. The Metallic Speaker will enter Bluetooth®mode.
2. Slide the power switch to the OFF position to power down
the Metallic Speaker.
© Buddee Gear 2017. All rights reserved. The Bluetooth®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Buddee
Gear Pty Ltd. is under license. Other trademarks and trade
names are those of their respective owners.
Made in China
AUX
TF CARD DC 5A ON OFF
1 2 3 4
1. AUX input
2. TF card input
3. Micro-USB charging port
4. Power switch (ON/OFF)
MODE BUTTON
• Switch between Bluetooth®and FM radio modes.
PHONE BUTTON
• Answer/ hang up incoming phone calls.
PREVIOUS/ VOLUME DOWN BUTTON
• Press to play a previous song or radio station.
• Press and hold to decrease volume.
PLAY BUTTON
• Press to play/pause a song.
NEXT/ VOLUME UP BUTTON
• Press to skip forward a song or radio station.
• Press and hold to increase volume.
BLUETOOTH®MODE
PAIRING A DEVICE AND PLAYING AUDIO
1. After turning on the Metallic Speaker it will enter Bluetooth®
mode. The LED indicator light will flash blue on the back of the
unit, this indicates that the Metallic Speaker is waiting to be
paired. While pairing remain within one metre of the earphones.
2. Using the controls on your Bluetooth® device, select
BD-MTLSPK-1 in your Bluetooth®settings menu. If your device
requires a password, enter 0 0 0 0. Refer to the manual of your
device for specific instructions on pairing and connecting
Bluetooth®devices.
3. Once pairing is successful, the LED display will stop flashing.
Audio played through the connected Bluetooth®device will now
be heard through the Metallic Speakers.
4. Use the controls on your connected device to select and
begin to play audio. To play/pause audio, skip songs or
change the volume use the controls on the top of the Metallic
Speaker or the controls on your connected device.
ANSWER PHONE CALLS
1. To accept a phone call, firstly pair your mobile with the
Metallic Speaker via Bluetooth®. Once paired, press the
answer/hang up button located on the top of the Metallic
Speaker to accept an incoming call. You can now speak
through the inbuilt microphone.
2. To end the call, press the answer/hang up button once
more.
NOTE: You can also use the controls on your mobile phone.
TF/ MICRO SD CARD MODE
1. Insert your TF or microSD card into the slot located on the
back of the Metallic Speaker. The speaker will begin to play the
mp3 files stored on the card.
2. Use the controls located on the top of the Metallic Speakers
to play/pause, adjust volume or skip songs stored on your TF
or microSD card.
AUX LINE-IN MODE
1. Insert a 3.5mm AUX cable into the AUX port located on the
back of the Metallic Speaker. Press the mode button until
you reach the AUX Line-In mode.
2. Begin playing audio via your connected AUX device and the
sound will be played through the Metallic Speaker.
FM RADIO MODE
1. Plug in the micro-USB cable into the charging port on the
back of the device. Press the “M” (mode) button twice to reach
FM radio mode. The speaker will sound “radio mode”. If the
speaker sounds “Bluetooth®ready to pair”, short press the "M”
button again.
2. Scan through radio stations by pressing the previous and
next buttons.
3. For auto-tuning, press the pause button once. The speaker
will now search for radio channels automatically.
NOTE: For radio operation, ensure the micro-USB cable is
plugged in (the USB end does not need to be connected) to act
as an aerial. The AUX cable (included) can also be used as an
aerial by connecting one end of the 3.5mm AUX cable to the
back of the unit via the AUX Line-In port.
TECHNICAL SPECIFICATIONS
Input: DC5V
Output Power: 3W x 2 (RMS)
Battery: LitIon 1200mAh
Battery life: 4 hours at 80% volume
Frequency: 50Hz-20KHz
Input Sensitivity: 400mV
Signal to Noise Ratio: ≥88Db
External Magnetic Horn: 40mm x 2
Bluetooth®: Version 3.0.

PACKAGE CONTENTS
Before attempting to use this unit, please check the
packaging and make sure the following items are contained
in the shipping carton:
• Metallic Bluetooth®Speaker
• Micro-USB charging cable
• 3.5mm AUX cable
• User manual
CHARGING
1. Insert the micro-USB end of the included cable into the
charging port on the back of the Metallic Speaker.
2. Insert the USB end into a powered USB source such as a
computer, laptop or USB wall charger. The charging indicator
will light up red.
NOTE: Please fully charge the Metallic Speaker prior to first
use.
POWERING ON
1. Slide the power switch to the ON position and the display
will light up. The Metallic Speaker will enter Bluetooth®mode.
2. Slide the power switch to the OFF position to power down
the Metallic Speaker.
BLUETOOTH®MODE
PAIRING A DEVICE AND PLAYING AUDIO
1. After turning on the Metallic Speaker it will enter Bluetooth®
mode. The LED indicator light will flash blue on the back of the
unit, this indicates that the Metallic Speaker is waiting to be
paired. While pairing remain within one metre of the earphones.
2. Using the controls on your Bluetooth® device, select
BD-MTLSPK-1 in your Bluetooth®settings menu. If your device
requires a password, enter 0 0 0 0. Refer to the manual of your
device for specific instructions on pairing and connecting
Bluetooth®devices.
3. Once pairing is successful, the LED display will stop flashing.
Audio played through the connected Bluetooth®device will now
be heard through the Metallic Speakers.
4. Use the controls on your connected device to select and
begin to play audio. To play/pause audio, skip songs or
change the volume use the controls on the top of the Metallic
Speaker or the controls on your connected device.
ANSWER PHONE CALLS
1. To accept a phone call, firstly pair your mobile with the
Metallic Speaker via Bluetooth®. Once paired, press the
answer/hang up button located on the top of the Metallic
Speaker to accept an incoming call. You can now speak
through the inbuilt microphone.
2. To end the call, press the answer/hang up button once
more.
NOTE: You can also use the controls on your mobile phone.
TF/ MICRO SD CARD MODE
1. Insert your TF or microSD card into the slot located on the
back of the Metallic Speaker. The speaker will begin to play the
mp3 files stored on the card.
2. Use the controls located on the top of the Metallic Speakers
to play/pause, adjust volume or skip songs stored on your TF
or microSD card.
AUX LINE-IN MODE
1. Insert a 3.5mm AUX cable into the AUX port located on the
back of the Metallic Speaker. Press the mode button until
you reach the AUX Line-In mode.
2. Begin playing audio via your connected AUX device and the
sound will be played through the Metallic Speaker.
FM RADIO MODE
1. Plug in the micro-USB cable into the charging port on the
back of the device. Press the “M” (mode) button twice to reach
FM radio mode. The speaker will sound “radio mode”. If the
speaker sounds “Bluetooth®ready to pair”, short press the "M”
button again.
2. Scan through radio stations by pressing the previous and
next buttons.
3. For auto-tuning, press the pause button once. The speaker
will now search for radio channels automatically.
NOTE: For radio operation, ensure the micro-USB cable is
plugged in (the USB end does not need to be connected) to act
as an aerial. The AUX cable (included) can also be used as an
aerial by connecting one end of the 3.5mm AUX cable to the
back of the unit via the AUX Line-In port.
TECHNICAL SPECIFICATIONS
Input: DC5V
Output Power: 3W x 2 (RMS)
Battery: LitIon 1200mAh
Battery life: 4 hours at 80% volume
Frequency: 50Hz-20KHz
Input Sensitivity: 400mV
Signal to Noise Ratio: ≥88Db
External Magnetic Horn: 40mm x 2
Bluetooth®: Version 3.0.