Buffalo 6011.037 User manual

Model Name:Hockey Table
Model Number:6011.037
INSTRUCTIONS MANUAL

Part List
LEG - PANEL -
RIGHT
PLAYFIELD -
HOCKEY TABLE LEG - PANEL -
LEFT LEG - BASE LEG INSIDE PANEL
LEG END BRACE LEG SIDE BRACE LEG PANEL
CORNER LEG LEVELER - 5” GOAL - BOX
Shaded box = pre-installed part
BATTERY BOX PUCK CATCHER WIRE LED SCORING SCORER BASE BOX
BOLT - HEX HEAD
- 8 X 63.5 MM BOLT -
ALLEN KE
6.5 X 19 MM
PUSHER -
SOMBRERO - RED FELT PAD
WASHER - 8 X 19 MM WASHER - 6 X 15 MM
SCREW - ROUND
HEAD - 4 X 25 MM
SCREW - FLAT
HEAD - 4 X 45 MM
PUCK - ROUND -
RED
SCREW - ROUND
HEAD - 4 X 12 MM WRENCH
#1 #2 #3 #4 #5
#6 #7 #8 #18 #19
#39 #40 #41
1PC 4PCS 4PCS
2PCS 2PCS 4PCS 4PCS 2PCS
2PCS 2PCS 2PCS
#47 #48 #49
16PCS 16PCS 16PCS
#50
16PCS
#51
16PCS
#52 #53 #54
24PCS 20PCS 1PC
#31 #32 #33 #34
1PC 2PCS 1PC 1PC
4PCS 4PCS

STEP 1
= (4)
2
= (4)
3
8= (4)
STEP.1
2
3
8
2
3
8
53 = (16)
8
2
3
53
53
53
53
32
4
51
STEP.1C
51 = (16)
= (4)
4
STEP 2:
Hold two Leg Panels -Right and Left (#2 and #3). See Step.1.•
Slide one Leg Panel Corner (#8) between the Leg Panels (#2and #3). See Step.1A.•
Turn over the Leg assembly and then attach two Screws (#53) to the top of the middle of the Leg assembly. See Step.1B.• Attach four Leg Bases (#4) to Leg assemblies using four Screws (#51) per Leg Base. See Step.1C• Repeat the above steps for the other Leg Panels (#2 and #3) Corners (#8) and Leg Base (#4).•
STEP.1A
STEP.1B

STEP 2
47
48
47
48
2
3
47
48
1
= (16)
47 48 = (16) 54
54
= (1)
STEP 2:
Attach the four Leg assemblies to the table (#1) using four Bolts (#47), eight Washers (#48) per leg• assembly. See Step. 2A.
STEP.1A

= (2)
6= (2) 718 = (4) 49 = (16)
= (4)
5
50 = (16) 52 = (24) 53 = (4)
5
2
52
5
7
7
6
1
49
50
18
49 50
6
STEP 3:
Attach two Leg End Panels (#6) and two Leg Side Panels (#7) between two Legs using four Bolts (#49) with four washer (#50)
per Leg End Panel and
• Side Panel.
Screw four Leg Levelers (#18) into the four Legs. See Step.3.•
•
•
You will need 4 or more adults for this step. Carefully lift the assembly off the floor and turn it over.
CAUTION: Make sure that you place the table squarely onto its legs or damage to the table may occur.
DO NOT LEAN THE
TABLE ON ITS LEGS
HOLD TABLE
CABINET DO NOT HOLD THE LEGS
19
53
•
[4] Attach the Goal Boxes (#19) to the Cabinet (#1) using two Screws (#53) per Goal Box.See Step.3B.
19
19 = (2)
STEP.3
STEP.3A
STEP.3B
STEP.3C
Attach four Leg Inside Panels (#5) to the Leg assemblies using six Screws (#52) per Leg Inside Panel.See Step.3A.
•
Peel the backing off 40 Felt Pad and attach to 39 Pusher as shown in
40
40 39
NOTE: A3 Felt Pads may
already be attached to
A1 Strikers.
Step.3C.

ELECTRICAL CONNECTIONS DIAGRAM
STEP 4:
• Connect the wires under the table as shown above.
• WARNING! Do not mix old and new batteries. Do not
mix alkaline, standard (carbon - zinc), or rechargeable (nickel
cadmium) batteries. Do not dispose of batteries in fire, batteries
may explode or leak.
NOTE: Please clean the battery contacts of the device prior
to battery installation. Make sure to remove batteries from the
scorer when not used for an extended period of time. Remove
used batteries promptly.
ELECTRONIC SCORER OPERATION:
1. Under the table, remove screw using a small phillips screwdriver and open the battery box. Insert 4(four) pcs AA
batteries (not included) in the order of polarity as shown on the inside cover. Then close using a small phillips
screwdriver.
(If the game will not be used for a long period of the time, we recommend that the batteries be removed).
2. Turn on the scorer using the on/off switch located on the scoring display. You will hear music and the Home
and Visitor screens will show “00”.
3. There is one pre-set period of 15 minutes which can be adjusted to 10 minutes, 5 minutes, or “No Time Limit”
mode by pressing the “MINUTES” button.
4. Press the “START/RESET” button to start the game.
5. During Play - When “START/RESET” button is pushed, the following will occur:
Home and Visitor Score will reset to “00” and time will reset to it’s original setting.
6. “Sound ON/OFF” - Press this button while the game is on to turn the sound OFF and ON.
7. Once Home or Visitor reaches “99” points, Home or Visitor display will stop the scorer and keep flashing.
Please reset it by pressing the “START/RESET” button.
NOTE: If no score has been made for 15 minutes, the scoreboard will automatically turn off. You can turn it on
again by pressing the “START/RESET” button. However, we suggest turning the power off when the game will
not be used for an extended period of time.
33 - LED Scorer
& Timer Display
31 - Battery Box
34 - Main Electronic
Unit
32 - Scoring Sensors
with Wire
32 - Scoring Sensors
with Wire