Bush WMNSINT612W User manual

Instruction manual
WMNSINT612W
WMNSINT714W

You’ll soon be enjoying your new washing machine.
It all begins here, with your instructions. Don’t worry,
there’s nothing too technical coming up. Just simple,
step-by-step guidance to get you up and running
quickly. Sound good? Then let’s get started.
Help and Guidance
We’re here to help you get the most from your . Should you require washing machine
any guidance, a simple solution can often be found online at:
www bush-support.com.
If you still require further assistance, call one of our experts on 0345 257 7271.

3
or online at www.bush-support.com If you still require further assistance, call one of our experts on 0345 257 7271.
Contents
Product support
Troubleshooting 38
Help and assistance 39
Declaration of conformance to product
standards 40
Disposal 41
7
Safety information
Safety information 6
Getting to know your
washing machine
Ready? Let’s begin 10
Accessories 12
Installing your washing
machine
Installation requirements 14
Unpacking 14
Connections (electrical, water, gas) 15
Functions
Functions 18
Using your washing machine
First use of washing machine 28
Standard and advanced functions/use
29
Care and Maintenance
Cleaning
33 actions
Maintenance
33
Technical specifications 35
1
2
3
4
5
6

1Safety information

Safety information
Important - Please read these instructions fully before
installing or operating
Safety information
6
If the supply cord is damaged,it
must be replaced by the
manufacturer,its service agent or
similarly qualified persons in order
to avoid a hazard.
The new hose-sets supplied with
the appliance are to be used and
that old hose-sets should not be
reused.
This washing machine is for indoor
use only.
The openings must not be
obstructed by a carpet.
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical,sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safeway and understand the
hazards involved.
Cleaning and maintenance shall
not be made by children without
supervision.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of
• the appliance by a person
responsible for their safety.
Pull out its plug from the power
socket before cleaning or
maintenance.
Make sure that all pockets are emptied.
Sharp and rigid items such as coin,
brooch,nail,screw or stone etc.may
cause serious damages to this machine.
Pull out its plug and cut off water
supply after the operation.
Please check whether the water inside
the drum has been drained before
opening its door.Please do not open
the door if there is any water visible.
Pets and children may climb into the
machine. Check the machine before
every operation.
Glass door may be very hot during
the operation.Keep children and pets
far away from the machine during
the operation.
Take care that power voltage and
frequency shall be identical to those
of washing machine.
Do not use any socket with rated
current less than that of washing
machine.Never pull out power plug
with wet hand.
To ensure your safety,power cord
plug must be inserted into an earthed
three-pole socket.Check carefully
and make sure that your socket is
properly and reliably earthed.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

Children of less than 3 years should
be kept away unless continously
supervised.
Do not let kids play with the
machine.
Packing materials may be
dangerous to the children . Please
keep all packing materials (plastic
bags,foams etc) far away from the
children.
Washing machine shall not be
installed in bath room or very wet
rooms as well as in the rooms with
explosive or caustic gases.
7
or online at www.bush-support.com. If you still require further assistance, call one of our experts on 0345 257 7271.
Safety information
Important - Please read these instructions fully before
installing or operating
Safety information
Make sure that the water and
electrical devices must be
connected by a qualified technician
in accordance with the
manufacturer's instructions and
local safety regulations.
Before operating this machine,all
packages and transport bolts must
be removed.Otherwise,the washing
machine may be seriously
damaged while washing the
clothes.
Before washing the clothes at first
time, the washing machine shall be
operated in one round of the
whole procedures without the
clothes inside.
The washing machine with single
inlet valve only can be connected
to the cold water supply. The
washing machine with double inlet
valves can be connected to the hot
water and cold water supply.
Your washing machine is only
for home use and is only
designed for the textiles suitable
for machine washing.
Flammable and explosive or toxic
solvents are forbidden.Gasoline and
alcohol etc.Shall not be used as
detergents.Please only select the
detergents suitable for machine
washing, especially for drum.
It is forbidden to wash carpets.
Be careful of burning when washing
machine drains hot washing water.
Never refill the water by hand during
washing.
After the program is completed,
Please wait for two minutes to open
the door.
Please remember to disconnect
water and power supply immediately
after the clothes are washed.
Do not climb up and sit on top cover
of the machine.
Do not lean against machine door.
Please do not close the door with
excessive forces.If it is found difficult
to close the door,please check if the
excessive clothes are put in or
distributed well.
The household washing machine
isn't intended to be built-in.
Cautions during Handling Machine
1.Transport bolts shall be reinstalled
to the machine by a specialized
person.
2.The accumulated water shall be
drained out of the machine.
3. Handle the machine carefully.
Never hold each protruded part on
the machine while lifting. Machine
door can not be used as the handle
during the conveyance.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

Getting to know your 2
washing machine

Getting to know your washing machine
You’ll be up and running in no time
10
Ready? Let’s begin...
Please read these instructions carefully. They contain
important information which will help you get the best
from your and ensure safe and washing machine
correct installation and operation.
If you require any further assistance, our technical
experts are happy to help. For full details, refer to
the product support section at the end of these
instructions.
Getting to know your washing machine

Component
1.Detergent Drawer 7.Transport bolt x 4
5 6
7
7 7
7
8
11
or online at www.bush-support.com. If you still require further assistance, call one of our experts on 0345 257 7271.
4.Control Panel
5.Power lead
3.Filter 6.Drain hose
2.Door
Getting to know your washing machine
You’ll be up and running in no time
Getting to know your washing machine
8.Water inlet
4
5
6
1
2
3

WMNSINT612W /WMNSINT714W 6kg / 7 kg
Capacity
1200 /1400 rpm A++

3
Installing your washing machine

Installing your washing machine
Bringing it all together
14
Installation requirements
Levelling feet
In addition to the instructions mentioned here,
special regulations of the relevant water and
companies may apply. If in doubt, have the
washing machine connected by a qualified
technician.
The washing machine is heavy - caution when
lifting it.
Do not lift by projecting components (e.g.
washing machine door).
Warning: Frozen hoses may tear/burst. Do not
install washing machine in outdoor areas or
where there is a risk of frost.Please operate
washing machine above 0℃.
Lay hoses and cables in such a way that there is
of tripping over them.no risk
An additional space (approximately 120mm) is
required at the rear of the washing machine.
This is to allow
hose and drain hose connections.
enough space for the water
Unpacking
Unpacking your washing machine
Caution:2 people are required to unpack the
washing machine,it is recommended that gloves
are worn.
Carefully remove all packing materials including
the foam base, dispose of correctly.
Note:When opened,water droplets may be visible
in the drum etc. this is normal as each appliance
is tested before delivery.
Removing the transport bolts
Important:The bolts are designed to
support the internal components during transit
these MUST be removed before use.
2:Remove the bolts by pulling them.( 3)
transport
Fig
1:For your machine to work efficiently with
minimum vibration it should be settled on flat,
nonslippery,firm ground.
2:You can adjust the balance of your machine by
changing the positioning of its feet.
3:First,loosen the plastic adjustment nut.(Fig 5)
4:Adjust by rotating the feet upwards or
downwards.(Fig 6)
5:After the desired position has been reached,
tighten the plastic adjustment nut again by rotating
it upwards.
Note:Never put cartons,wooden blocks or similar
materials under the machine to balance
irregularities in the level of the ground.
Fig1 Fig2
•
•
•
•
•
Fig3 Fig4
Fig5 Fig6
1:Loosen the screws by rotating counterclockwise
with a suiltable wrench,(Fig 1 2)
3:When the transport bolts have been removed,
insert the plastic transport screw taps found in
the accessories bag into the holes.(Fig 4)
Installing your washing machine

or online at www.bush-support.com. If you still require further assistance, call one of our experts on 0345 257 7271.

1. Make the mark on the door according to the carbinet and washing machine height.
Preparation the Fixed position paper(Fig 10)
Position Paper
16 Installing your washing machine
2.Fixed position paper on the door.(Fig 11)
Paste on the Door(The door open
from right to left)
Shear fixed position paper
Position Paper
left open
Top Top
Left O pen Right Open
Installing your washing machine
Bringing it all together
Position Paper
right open
Paste on the Door(The door open
from to )left right
Fig11
Fig10

4.Installation the hinges and spacer(Fig 13)
Fix the hinges to the machine by means of the ST4*12 screws included.
3.
Drill the hole on the door fixed position paper.
Drill hole on the door(Fig 12)
according to the
16-22mm
12mm
35mm
12mm
2mm
17
or online at www.bush-support.com. If you still require further assistance, call one of our experts on 0345 257 7271.
Installing your washing machine
Installing your washing machine
Bringing it all together
Door to open from right to left Door to open from left to right
Fig13
Fig12
Product support
5.Installation the counter magnet(Fig 14 & Fig 15)
The appliance is prearranged for a magnetic closure of the door. To enable a correct
operation of this device, it is necessary to screw the counter-magnet into the inner side
of the door with M5*12 screws.
Door to open from right to left
Fig14

6.Installation the door(Fig 16 & Fig 17)
If you have any doubt on the installation, please consult the qualified person.
18 Installing your washing machine
Installing your washing machine
Bringing it all together
Product support
Door to open from left to right
Fig15
Fig16
Fig17
Fix the cabinet with M5*12 screws.

19
Connections Electrical
or online at www.bush-support.com. If you still require further assistance, call one of our experts on 0345 257 7271.
Water inlet hose connections
Important:This washing machine MUST only be
connected to a cold water supply.
1:Connect the water inlet hose,the angled
connection attaches to the water inlet on the
back of the washing machine.(Fig 18)
2:The straight connection attaches to the water
supply valve.(Fig 19)
3:Ensure all seals are in place before connecting.
Important:Only tighten the hose connection nut
by hand - do not overtighten.
Drain hose connections
Important:The height of the top of the curve in
the drain hose MUST be between 60 - 100cm
from the floor.(Fig 20)
Drain hose can be fitted to the drainer or
a wash basin.
Max.100cm
Min.60cm
Fig18
Fig19
Fig20
Any electrical work that is required to
install this appliance MUST be carried
out by a qualified electrician.
Warning:THIS APPLIANCE MUST BE
EARTHED
Before making any electrical connections,
ensure that:
Electrical safety is only guaranteed when the
earth system of your house is in accordance
with the related local regulations.
•
• Do not bend, stretch or pull the supply cable
to avoid electric shock.
• Ensure the power socket is suiable for the
maximum power of the machine (fuses in the
power circuit must be 13 amp).
• The supply voltage should be the same as that
indicated in the technical specifications and
the applicance rating plate.
• The appliance should be earthed and in
complicance with the applicable law.
• When installed,the power socket must be
within easy reach.
• If the socket outlets in your home are not
suitable for the plug supplied with this unit
check with a qualified electrician for
replacement.
• To avoid the risk of overloading your plug
socket, the use of adapters, multiple connectors
• The applicance must be connected to a
220-240 volt 50Hz AC supply by means of
a three pin socket, suitably earthed and
protected by a 13 amp fuse.
• Should the fuse need to be replaced , a 13
amp fuse approved to BS 1362/A must be
used.
• The plug contains a removable fuse cover
that must be refitted when the fuse is replaced.
if the fuse cover is lost or damaged, the plug
must not be used until a replacement cover
has been fitted or the plug is replaced.
• A damaged plug should be cut off as close to
the plug body as possible , the fuse should be
removed and the plug disposed of safely.
Installing your washing machine
Bringing it all together
Installing your washing machine
or extension cables are not recommended.

20
Plug replacement (UK lreland only)&
Should you need to replace the plug;the wires
in the power cable are coloured in the following
way:
Blue - Neutral ’ N’
Brown - Live ’ L’
Green Yellow - Earth ’E’ &
As the colour of the wires in the power cable
may not correspond with the coloured markings
identifying the terminals in your plug,and
proceed as follows(Fig21):
The green yellow wire must be connected to
the terminal in the plug that is marked with the
letter E or by the earth symbol.
&
The blue wire must be connected to the terminal
that is marked with the letter N.
The brown wire must be connected to the terminal
that is marked with the letter L.
If power supply cord is damaged , it must replaced
by the manufacturer or its service agent or a
similar qualified person in order to avoid a hazard.
Fig21
Installing your washing machine
Bringing it all together
Installing your washing machine