Bushnell BackTrack D-TOUR 360310BG User manual

B
C

TABLE OF CONTENTS PAGE #
ENGLISH
FrANçAIS
ESPAñOL
DEuTSCH
ITALIANO
3-13
14-24
25-35
36-46
47-57

3
Control & Display Guide
1. POWER Button
2. MARK Button
3. TRIP Button
4. SETUP Button
5. USB Port
6. Location Icon (1 of 5)
7. Local Time
8. Direction to Location
9. Distance to Location
10. Battery Level
Indicator
11. Satellite Lock Icon
12. Trip Icon
Battery
Cover
Lock
Fig. 1
Note: Serial # is
inside battery
compartment.
Right Side
2
45
Left Side
13
FRONT VIEW
SIDE & BACK VIEWS
12
3
4
5
6
7
8
9
10
11
12
ENGLISH

4
BASIC SETUP
• Unlock/open battery cover and insert 3 AAA batteries*
(Fig 1, pg 3). Record the serial # inside-you’ll need it
later to register your D-Tour online. Close the cover.
• Go outdoors. HOLD POWER (1) (keep the button
pressed) until the display comes on. Wait for GPS
satellite lock (icon stops blinking) (11). This may take
a few minutes after the first power-up in a new area.
• Press SETUP (4). Press MARK (2), then press the TRIP
(3) or SETUP button to set the Hour for your area (Fig.
2). Press MARK to return to the Setup screen.
• To change the time and temp/distance formats, press
SETUP to select “12h” or “0F/yd”, then press MARK to
set to “24h” or “0C/m”. (Fig. 3). The arrow’s function
is explained on the next page. Press POWER to exit
Setup screen.
MARKING/RETURNING to a LOCATION
• Press POWER to select one of five Location icons or up
to 5 additional locations with number designations
(6) (Home, Car, Star, Flag, Target, #1-5). While standing
at the Location you want to mark, HOLD MARK to
save its position in the D-Tour’s memory (the display
will change as shown) (Fig. 4). You can now turn the
power off (HOLD POWER) and leave the location.
• To return to the location you marked, turn the D-Tour
on. Make sure the same icon or # you used to mark
the location is shown (if not, press POWER to select
it). The display indicates the direction and distance
back to the location (Fig. 5). Move in the direction
of the arrow, watching for the distance to decrease.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
* Do not mix old and new batteries. Do not mix battery
types-use ALL lithium or ALL alkaline.

5
Fig. 8
Fig. 7
Fig. 98
When you reach the location, the“Mark” icon will flash
in the center of the display.
• You can use the five icons (and up to 5 numbers) to
mark five different locations of any kind (your car, tent,
scenic area, etc.). Be sure you select a different icon or
# to store each new location. If you hold down MARK
with a previously used location icon still selected, you
will replace that one with your current location.
• To expand or restrict the number of “extra” locations
(numbers from 1 to 5) that are available, press SETUP
(4) three times until the location arrow on the lower
right is highlighted. Press MARK (2), then use the
TRIP/DATA or SETUP buttons to decrease or increase
the number below the arrow (Fig. 6). Press the MARK
button to confirm and return to the Setup screen.
OTHER SCREENS
• Press POWER once again after the “Target” location
icon screen to view the temperature and altitude at
your current location (Fig. 7).
• Press POWER again to view the Compass screen,
displaying the Latitude and Longitude of your current
location, and a digital compass display including your
heading (direction of travel) in degrees (Fig. 8).
AUTO POWER OFF/BACKLIGHT
• Power automatically turns off after 10 minutes if no
buttons have been pressed (except in Trip mode,
described next). HOLD POWER to turn the unit off
manually.
• Press the MARK button to turn the display backlight
on. It automatically turns off after 30 seconds.
Fig. 6

6
COMPASS CALIBRATION
• To ensure directional accuracy, hold the D-Tour out
in front of you and move it in a “Figure 8” pattern
a few times to re-calibrate the compass (Fig. 9). A
compass calibration video is available at: http://www.
bushnell.com/products/gps/instruction-videos/.
• For best results, we recommend holding the D-Tour
in a horizontal position (not tilted) during use (Fig.
10).
RECORDING A NEW TRIP (ROUTE)
• Press TRIP (3) to enter Trip mode. HOLD the TRIP
button to start recording new trip data. The display
shows a moving “hiker” icon, along with updated
readouts of elapsed distance and average speed
during your trip (Fig. 11). Keep the D-Tour powered
ON during your trip.
• To stop recording the trip data, HOLD the TRIP
button again.
• The D-Tour automatically saves the data it collects
between the time you start and stop recording your
trip, including the date and time of the trip, total
distance traveled, your average speed, and changes
in altitude and temperature.
VIEWING THE TRIP DATA SCREENS
• Press the TRIP button to view the distance and
average speed of your last trip, along with a remaining
memory indicator (% of trip data memory used) (Fig.
12). The D-Tour can store up to 48 hours of total trip
data (can be multiple trips on different days).
• Press the TRIP button briefly again (don’t hold the
button down in Trip mode or you will start a new trip
or stop your current trip) to display the “breadcrumb”
screen (Fig. 13), showing your route traveled (from
start to stop points of current or last trip).
Fig. 12
Fig. 10
Fig. 11
Fig. 13

7
VIEWING TRIP DATA
After recording at least one trip, connecting the D-Tour to your computer will
enable you to see the path you took on any of 4 types of map, view a trip data
graph, and share your trip via email or social media. To get the software:
• Go to http://backtrackdtour.com/ and follow the directions to create an
account (free) and register your D-Tour, and download the software app (Fig.
15, next pg.). Your account provides online backup for all your trip data. (Serial
number is inside the battery compartment-(Fig. 14). After registering, you’ll be
taken to a screen to download the D-Tour application (Fig. 16) (Adobe Air® is
required-it will be installed automatically if you do not already have it on your
computer). Click “Download Now”, then select “Open”. A link to download the
software will also be provided in your confirmation email. Turn on the D-Tour
and connect its USB port to your computer with the supplied USB cable. On
Windows® PCs, the app should open automatically (if not, click the desktop
icon (Fig. 17).
Fig. 15 Fig. 17
Fig. 16
Fig. 14

8
a
b
c
d
f
e
Fig. 19
Fig. 18

9
Note: if you get a Windows “AutoPlay” popup when you connect your D-Tour,
click “Open Folder to View Files”, then double click a .btk (trip data) file). On
Mac®, double click the “D-Tour” icon in your Applications folder to launch the
application.
• Enter the User Name (email address) and Password you used when setting up
your account, then select “LOGIN” (Fig. 18). This will enable all your trip data
to be stored within your online account, so it will be automatically backed up,
and accessible to you from any computer.
USING THE D-TOUR APP-Basic Features (Fig. 19)
• After the D-Tour app opens, you will see one or more gray folders on the
left (a) below “My Downloaded Tracks”, each labeled with a date. Each folder
contains information on the trips taken in a 24 hour period.
• Click the folder to open it and view the individual trips (b) you made on that
date (the duration of each trip is based on the time elapsed between the
starting and stopping of a new trip recording when you held down the TRIP
button).
• The route you traveled for each trip is shown as a colored line (c) on a map.
Four types of maps are available-click on the name of a map type (d) to
change the view:
MAP-a “road map” style view, complete with road names.
SATELLITE-an aerial photo of the area.
HYBRID-a combination of the first two maps.
TERRAIN-this is a topographic map showing elevation data for the area.
• The zoom slider and position arrow pad allow you to zoom in/out and move
around on the map (e).
• Click on the name of a trip to highlight it on the map. You can hide any trip by
clicking on the “eye” icon next to it’s name (f).
• To change the name of a folder (from the default date to something like
“Canyon Trip Day 1”), right click on its name. You can also right click on a trip
within the folder to rename it.

10
Please read the Google™ Maps Terms of Service at:
http://maps.google.com/intl/en/help/terms_maps.html
USING THE D-TOUR APP-Additional Features (Fig. 20)
• Clicking on the “handle” (g) at the bottom center of the map screen will open
a popup graph displaying the altitude, temperature and speed data from the
trip. You can use the pull-downs (h) to change how the data is displayed. This
feature is ideal for runners and bikers that want to track their performance on
an exercise course over time.
• To create a new folder, click the plus (+) icon on the bottom left (i). Existing
trips can be dragged from their original folder into the new one.
• To delete a trip or trips folder, drag it to the trash icon (j).
• If you’d like to share the details of your trips, we’ve made it easy. Just click
“Export Current Map” (k) and select a save or share option.
• The “Save As” option allows you export the current map view as a .jpg photo.
• When you have finished using the D-Tour application, you don’t need to
logout, just close the application (l). Your trip data is automatically saved in
your account.
USING THE D-TOUR APP ON OTHER COMPUTERS
If you want to access your D-Tour trip information from another computer, it is not
necessary for you to create a new account. Simply login to your account at http://
backtrackdtour.com click on the download link, and install the app.
LOGIN/CHANGE PASSWORD
If you log out of the D-Tour application, you will be prompted to log in again
the next time you launch the application. If you forget your password or want
to change it, you may click on the “Forgot Password?” link on the application log
in screen (Fig. 21). You may also change your password after logging in to your
existing account at http://backtrackdtour.com. Click “My Profile” in the menu at
the top of the screen (Fig. 22).