BVE AXCESS RETRO User manual
BroadcastVision Entertainment : www.broadcastvision.com
PROGRAMMING INSTRUCTIONS
1) PROGRAMING PRESETS CHANNELS
a) Press and Hold CHANNEL DOWN and VOLUME DOWN simultaneously for 5 seconds. A
decimal point will appear in each corner of the frequency display indicating you are in the
Preset Channel Program.
b) Select the frequency you wish to set using the Channel Up/Down Buttons.
c) Select the Preset position number (1-52) you wish that frequency to be set to using the
Volume Up/Down buttons.
d) Press the EQ button to save the frequency to the preset. You will automatically advance to
the next preset channel. There are 52 preset channel positions available.
e) To delete a preset, press and hold the ‘EQ’ button until the display flashes. It is easiest to
start with the lowest channel to be erased since the presets will automatically increment.
f) Press and Hold CHANNEL DOWN and VOLUME DOWN simultaneously for 5 seconds to
EXIT Preset Channel Programming Mode.
HEADPHONE JACK REPLACEMENT
1) Unscrew the Headphone Access Door retaining screw. The screw will remain captured in
the door.
2) Open the hinged Access Door.
3) Using thumb nail or flat blade screw driver pry the headphone jack at its end until it comes
loose on the pin, and then remove the old jack.
4) Insert a new headphone jack over the pin and push onto the pin until it fully seats.
5) Close the door and insure the pin is aligned in the hole of the door. Use a small screw driver
if necessary to insure it is centered in the hole in the door.
6) Secure the Headphone door by using the door screw.
BroadcastVision Entertainment : www.broadcastvision.com
FCC Compliance Statement
This equipment complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the unit off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult Broadcastvision Entertainment or an experienced radio/TV technician for help
This equipment has been verified to comply with the limits for a Class B computing device,
pursuant to the FCC Rules. Operation with non-approved equipment is likely to result in
interference to radio and TV reception. The user is cautioned that changed and modifications made
to the equipment without the approval of the manufacturer could void the user’s authority to
operate this equipment.
Canada Compliance Statement
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
BroadcastVision Entertainment : www.broadcastvision.com
Broadcastvision Entertainment Terms and Conditions
BVE Stock Items Returned for Credit
BVE manufactured products may only be returned for credit with written authorization from BVE within
30 days of the original invoice date. A 25% restocking fee will be charged for all returns. All products
being returned to BVE require a Return Authorization number. Products must be returned in original
condition with the original packaging, components and support material. Credit is contingent upon
inspection of returned items.
Return Authorizations
A Return Authorization number must be issued from BVE prior to any item being returned for credit,
repair or exchange. Items returned without approval will be refused and returned to the sender.
Requests for a Return Authorization number may be made to our Customer Service Department at 1-
888-330-4283.
Repairs and Replacements
A warranty repair of BVE manufactured product includes parts, labor and the return GROUND shipping
to the customer. Repairs made while under warranty are covered for the duration of the valid warranty
period. Non-Warranty repairs receive a “Repair Warranty” of 90 days parts and labor only. Warranties
do not include on-site service. Advance Replacements of items in question may be arranged if the
product is within 30 days of invoice date and is subject to product availability. Advance Replacements
must be secured by the customer with a valid Credit Card or Net30 terms of an account in good
standing.
Shipping
Shipping dates are estimates only. Products will be shipped per the designated Shipping Method.
Paying for an accelerated Shipping Method only indicates the product will ship by that method when the
product or repair is available. BVE will not be held responsible to accelerate shipping, discount invoices
or compensate customers for loss of profits, business or goodwill due to back orders, shortages,
shipping complications, damages, product malfunction, labor, construction, nature or delays.
Warranties
All products sold by BVE carry the original manufacturers’ warranty. Warranty begins on the invoice
date of purchase from BVE or an authorized BVE Dealer / Distributor. Warranty may alternately begin
on the date of installation with a valid Installation Completion Form from an authorized BVE Dealer,
Distributor or Installer. Warranties do not cover damage due to abuse, misuse, modification or the result
of any third party. Warranties are not transferable and cover only the original purchaser with a valid
invoice. Manufacturers will, at their option repair or replace equipment, as they deem necessary.
Warranties do not include “on-site” service
Table of contents
