Caldwell 1099107 User manual

1
Instructions #1100864 REV.A
Product #1099107
INSTRUCTIONS

2
CONTENT
A. HD Camera
B. Flexible Camera Mount
C. Long Distance Transmitter
D. Router Stand
E. Router Stand Stake
F.Wall Charger
G. Storage/Carrying Case
(not shown)
A.
B.
C .
D.
E.
F.
This product contains rechargeable batteries that might require
special handling at end-of-life. Please consult your local authorities for proper
recycling/disposal instructions
This system is designed to deliver a live video stream of a target to the shooters
location up to 400 yards away.

3
WARNINGS
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference
in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
2. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
3. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
4. FCC RF Radiation Exposure Statement Caution:To maintain compliance with the FCC’s RF exposure guidelines,
place the product at least 20cm from nearby persons.
5. The device must not be co-located or operating in conjunction with any other antenna or transmitter.
Changes or modications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
POWER OPTIONS
Internal Lithium Ion Battery (Standard Use)
• The transmitter includes an integrated
Lithium Ion battery packs for ease of use.
The transmitter can operate for up to 6
hours on a single charge.
External Power Options (Extended Use)
• Only required when continuous run time is
greater than 6 hours.
• The transmitter includes an external
power jack.This allows the user to utilize an
external power source.This power jack is a
standard male 2.1 x 5.5mm jack.
• The cord, with male 2.1 x 5.5mm jack, can be directly plugged into most standard 12V Battery Banks. (Photo 1)
• You can also connect the male 2.1 x 5.5mm jack to a fused wiring harness designed to work with terminal batteries,
such as deep cycle batteries.
Transmitter
Charge Port
Mounting
Point
(Photo 1)
External Power Jack
Camera Power
and COM

4
SETUP
Read through entire instructions prior to beginning setup
Smartphone Connectivity
1. Go to the appropriate application marketplace for your smartphone/mobile device and search for
“Caldwell Ballistic Precision Target Camera”.
2. Alternatively, http://www.btibrands.com/ provides direct links to the appropriate apps for the different mobile
platforms supported by Caldwell.
3. Once the app is installed you will see the Caldwell Ballistic Precision Target Camera app icon in your
smartphone home screen.
Transmitter Station Setup
• Position the Transmitter Station with consideration in
avoiding likely bullet path
• Deploy Router Stand
• Attach Transmitter to Router Stand (Photo 3)
• Adjust the Router Stand, until it is level and then use one of
the Router Stand Stakes to anchor the Router Stand (Photo 4)
• Extend Stand height. For optimal performance over long
distances, extend the Router Stand height to the maximum height.
• Point the front of the transmitter towards the shooting bench (Photo 3)
• Install Camera on the Camera Mount (Photo 5)
NOTE: Storage case is designed to store the
Camera assembled on the Camera Mount
(Photo 3)
(Photo 4)
Rotate
Stake next to
center pole
Transmitter
Charge Port
II O I
Switch Function
External
12v DC
Power
Internal
Battery or
AC Power
OFF
Mounting
Point
AC Power
• This kit comes with an AC Wall Charger. The transmitter can operate on the AC Wall Charger
alone, by connecting the charger to the charge port, if AC power is available. (Photo 2)
NOTE: Never connect anything except the included
AC wall charger to the charge port
(Photo 2)
Front
External Power Jack
Camera Power
and COM

5
• Attach Camera Mount to the Router Stand at the desired height (Photo 6)
• Connect the Camera power connector and communication connector (Photo 7)
• Power on the transmitter, select either External or Internal power
• Connect the Smartphone/tablet to the Wi-Fi network Transmitter(Your router number will follow “Transmitter”)
Rotate
(Photo 5) (Photo 6)
Clamp to
desired height
(Photo 7)
Camera
Power
Camera COM
• Open the app, and check the alignment of the camera,
and adjust as needed.You want to adjust the camera
to center the target in the viewing window on
your device.The app allows you to zoom and pan
for additional target centering.
• Review your Transmitter Station position, as zooming
and panning may allow you to reposition if desired.
TIP: Before going up range, turn on the Transmitter and connect
your phone/tablet to the Transmitter to verify the video is
transmitting to the Smartphone or Tablet
SETUP cont.

6
APPLICATION INSTRUCTIONS
• The app provides live stream of the target to the user
• The Connect/Disconnect button turns the camera display on/off
NOTE: This can be used as a master reset button, by cycling the camera off then back on
• The Snapshot button can be used to save a screenshot of the live video stream
• You can add a custom note to the image before saving (Example:“.308 Win, 100 Yards,Target 1)
• The Video button can be used to save a video from the live video stream
• The video length can be adjusted in the settings tab
SETTINGS TAB

7
• The Group Size calculator can be used to calculate the group size on a target
• Once all of the target hits have been selected, the group size will be displayed in the lower right corner
NOTE: By using the Snapshot button, you can save a screenshot of your calculated group. Only one group size can be
calculated and saved per target image screenshot.
• To clear the group, or back up one step, use the Back button or simply use the Connect/Disconnect button to
cycle the camera.
STEP 1 - Click Zoom/Pan measure grouping icon
STEP 2 - Draw a line, of known length close to the group
(Example: Most grid/line spacing on standard targets
are spaced at 1”)
STEP 3 - Enter the length of the line drawn in STEP 2
STEP 3 - Select all of the target hits. Click the screen to drop
a marker, and once the marker is dropped it can be
adjusted by clicking and dragging the marker

8
GENERAL RECOMMENDATIONS
• Although this system is designed to be weather resistant, it is not recommended that the device is left outside
for extended periods
• Always store your device in a dry location
• Do not submerge any of the components
• When transporting the device, use the storage/carry case to protect the components during transport
• Do not store the device with depleted batteries. It is recommended to charge the batteries before storing
for an extended period
• Use a lens cleaning cloth for cleaning the camera lens
• Clean dirt and debris off of components prior to storage, to prevent corrosion
TIPS
Power
Indicator
Wi-Fi
Indicator
Camera
Indicator
• Ensure clear line of sight between Transmitter and Smartphone or Tablet
• Extend Router Stand height to the max height
• If multiple systems are being used, take note of your router number to connect to the correct Wi-Fi network.
• When using the charger, the light on the charger will be RED during charging and GREEN when fully charged.
NOTE: If the video does not appear in the App, turn the Transmitter OFF and back
on. Then recheck the video stream.