CamnSmart E27SX1 User manual

Quick Guide
CamnSmart PTZ Wi-Fi Camera
1. Overview of the Cameras
Model: E27SX1

Model: E27XS2

Model: E27S

www.camnsmart.com
Model: E27

2. Download APP and Register a user account and login
Search and download “YCC365 Plus” in Apple Store or Android app store. Or
scan below QR code to download and install it to your phone.
Click “Sign up” to register your email as user ID and create a password according
to the procedure. After registration, you can login with your registered account.
In future login, if you forget your password, you can reset your password by clicking
"Forgot password” on the login page.
3. Add camera to App
1) Get ready your Wi-Fi router and remember your Wi-Fi password.
Note: A. please do not use special letters like "# % &" as Wi-Fi name and
password. B. Camera supports 2.4GHz Wi-Fi. If your Wi-Fi router is 5GHz, it
may be integrated with 2.4GHz. But 2.4GHz Wi-Fi and 5GHz Wi-Fi have the
same Wi-Fi SSID name. So, you can get to your Wi-Fi router's settings to set
2.4GHz Wi-Fi in a different name. Then you will see two Wi-Fi names listed
on your phone WLAN list. Your phone selects 2.4GHz Wi-Fi name to connect.
2) Please also open your location on your phone settings.
3) Login the app “ycc365plus”

4) If you use SD card for video recording, please prepare an SD card and insert
it to the camera SD card slot.
(Note: Because camera need to run for video stream. It requires SD card
with high-speed reading and writing. So please use C10 (Class10) or higher
speed SD card. U3 type will be preferable.)
5) Connect camera to power socket and turn on power. Wait about 30 seconds,
camera will rotate left-right and up-down. Then about 20 seconds, camera
will say “Please configure your camera by AP hot spot or scanning code”.
If camera does not rotate and no saying anything after 50 seconds, please
do following:
a) check power supplied properly and firmly.
b) please reset the camera. Below pictures show where are the reset buttons.
Use a pin to slightly press it for 3~5 seconds, till the camera voice “Reset
success”. Release the rest button, then the camera will do Step 5).
E27SX1
E27XS2
E27S
E27
E27SX1
E27XS2
E27S
E27

6) On the app, press “+”, Select “intelligent Camera”, select “Scan code to add”
7) Press “Next”.
On the Step 1), you already connected your phone to your Wi-Fi. So, it
automatically shows your Wi-Fi name. You just type in your Wi-Fi password,
then press “Next”.
Important note: you must type in correct Wi-Fi password, otherwise
connection will fail in following steps.

8) A QR code will show on your phone screen. Place the QR code in front of
the camera lens to let the camera read the QR code. You need to move the
QR code slowly forwards or backwards 10cm ~ 50cm distance to the camera
lens.
9) Once camera read the QR code, it will sound “Di Di” and voice “please wait
for Wi-Fi connecting” and voice “please wait for internet connecting”. Now
press “When you hear a beep or a green light” button on app. Then just wait.
Camera is added successfully to you APP account. Now you can use it.
www.camnsmart.com

4. APP Interface
5. Settings Interface

6. Use SD card to record video
Recording modes option in settings:
1) Not recording: it will not record video to SD card.
2) Alarm recording: when camera detects motion, it will record video to SD card.
3) Continuous recording: it always records video to SD card.
(Please get to Settings / Memory card management to set recording mode).
Notes:
1). If you already insert SD card into Camera BEFORE you add camera to the
app, it will automatically record video in “Alarm recording” mode.
2). If you insert SD card into Camera AFTER you add camera to the app,
please cut off power supply, then insert SD card to camera, and then supply
power again to camera. After camera connects internet again, please get to
settings to set recording mode to “Alarm recording” or “Continuous
recording”.
www.camnsmart.com
This Quick Guide may be revised without further notice. Copy writes by CamnSmart.