Capri Tools CP35205 Operator's manual

User Manual & Safety Instructions
Model: CP35205 / CP35210 / CP35210-6 / CP35215
TWIN POWER
IMPACT WRENCH
People. Passion. Quality.

2
People. Passion. Quality.
Specifications
CP35210 CP35210-6 CP35215
CP35205
Square Drive Square Drive Square Drive
Square Drive
Mechanism Mechanism Mechanism
Mechanism
Nut Busting Torque Nut Busting Torque Nut Busting Torque
Nut Busting Torque
Maximum Torque Maximum Torque Maximum Torque
Maximum Torque
Working Torque Working Torque Working Torque
Working Torque
Free Speed Free Speed Free Speed
Free Speed
Vibration Level (m/s2)Vibration Level (m/s2)Vibration Level (m/s2)Vibration Level (m/s2)
Air Inlet Air Inlet Air Inlet
Air Inlet
Air Pressure Air Pressure Air Pressure
Air Pressure
Blows per Min (BPM) Blows per Min (BPM) Blows per Min (BPM)
Blows per Min (BPM)
Noise Level (dBA) Noise Level (dBA) Noise Level (dBA)
Noise Level (dBA)
Air Consumption (CFM) Air Consumption (CFM) Air Consumption (CFM)
Air Consumption (CFM)
Minimum Hose Size Minimum Hose Size Minimum Hose Size
Minimum Hose Size
Weight Weight Weight
Weight
3/4” 3/4” 1”
1/2”
Twin Hammer Twin Hammer Twin Hammer
Twin Hammer
3,032 ft-lbs. 2,800 ft-lbs. 3,468 ft-lbs.1,715 ft-lbs.
1,600 ft-lbs. 1,490 ft-lbs. 2,000 ft-lbs.1,000 ft-lbs.
1,400 ft-lbs. 1,400 ft-lbs. 1,500 ft-lbs.700 ft-lbs.
5,200 RPM 5,200 RPM 5,000 RPM8,300 RPM
10.691 10.691 10.6918.686
3/8” NPT 3/8” NPT 3/8” NPT1/4” NPT
90 PSI 90 PSI 90 PSI90 PSI
940 940 9101,400
90.4 90.4 90.495.6
7.9 8.6 7.95.2
1/2” 1/2” 1/2”
3/8”
9.92 lbs. 12.12 lbs. 10.4 lbs.
3.52 lbs.
L: 5.91 in.
H: 7.40 in.
L: 8.39 in.
H: 11.93 in.
L: 14.52 in.
H: 11.93 in.
L: 8.78 in.
H: 11.93 in.
L L L
L
HHH
H

3
www.capritools.com
H
F, G
J
I
E
AC D
A. Square Drive
B. Twin Hammer clutch
C. composite body
D. twin power air motor
E. Trigger
F. forward/reverse dial
G. adjustable power dial
H. soft grip handle
i. exhaust
j. NPT Air Inlet
B

4
People. Passion. Quality.
• Read and understand this manual and safety
instructions in its entirety before using the tool.
Failure to follow these operating and safety
instructions can result in serious injury and property
damage.
• Onlyqualiedindividualswhoarefamiliarwithall
usage and safety instructions should be allowed to
use the tool.
• Always wear safety goggles and hearing protection.
• Wear face mask or respirator to reduce exposure to
chemicalsreleasedfromconstructionactivities.
• Wear gloves to reduce fatigue and avoid cuts and
burns.
• Donotwearclothingthat’sloosettingorhasloose
parts. Do not wear accessories such as watches,
necklaces, and bracelets. Restrain any long hair.
They can get caught in moving parts, which can
result in seriously injury.
• Do not operate the tool when you are tired or under
the inuence of any drug, medication, or alcohol.
Always stay mindful and alert when working with
the tool.
• Extendedexposuretothevibrationsofthetoolcan
be hazardous to your health. Take proper breaks
andavoidprolongedusage.
• Turn o the air supply and disconnect the air line
from the tool before performing any maintenance.
• Lubricate the tool before initial use.
• Lubricate the tool daily as well as before and after
each use.
• Lubricate the tool before storage.
• Do not modify the tool.
• Do not attempt to repair the tool. Repair should only
beperformedbyanauthorizedservicecenter.
WARNING: Personal Safety WARNING: Maintenance Safety
Read and understand this manual and safety instructions in its entirety before using this tool. Failure to
follow these operating and safety instructions can result in serious injury and property damage.
Always wear safety goggles.
Always use hearing protection.
Lubricate pneumatic tools daily as well as before and after each use to maintain optimal
performance.
Safety Instructions
Safety Information
• Do not use the tool if it has been damaged in any
way.
• Verify the integrity of the air supply system prior
to each use. Ensure air hoses and ttings are
damage free. Secure all connections.
• Keep air hose and couplers clean to prevent
grease and dirt from entering air supply system.
• Use minimum 3/8” (CP35205) and 1/2” (CP35210,
CP35215)airhosewithhighowcouplerstoallow
optimalairvolume.
• Do not use quick connect coupler to connect the
airhosetothetool.Thevibrationsfromoperating
WARNING: Equipment Safety

5
www.capritools.com
• Do not use the tool for non-intended purposes.
• Keep yourself well balanced with proper footing at
all times.
• Keep your hands dry, clean, and free from oil and
grease.
• Do not depress the trigger when connecting to the
air supply.
• Do not trigger the tool when it is not applied
directly to intended work objects. Attachments
can loosen and become dangerous projectiles.
• Do not point the tool at yourself or anyone else.
• Do not carry the tool by the hose.
• Do not exceed 90 PSI air pressure.
• Do not use oxygen or gases to power the tool. It
can result in explosion.
• Donotputhandsandbodynearmovingparts.
• Donotusethetoolnearliveelectricity.Thetoolis
not electrically insulated.
• Loosening fasteners will cause the tool to move
quickly away from the fastener and can entrap
your hands, arms, and body if there is not
sucientclearanceintherear.
• Keep work areas clean, well-lit and organized.
• Keep work areas well ventilated and free of
combustible materials.
• Donotallowchildrenornonqualiedindividuals
in the work area.
WARNING: work area Safety
DO NOT DISCARD THIS MANUAL
WARNING: operation Safety
• Turn o the air supply, depress the trigger to
release residual air, and disconnect the air line
from the tool each time before changing sockets
and attachments.
• Turn o the air supply, depress the trigger to
release residual air, and disconnect the air line
from the tool when the tool is not in use.
the tool will damage the coupler. Use a leader
hose to connect the air hose to the tool. The leader
hosereducesvibrationtocouplersandenhances
exibilityandsafety.
• Do not use sockets and accessories that are worn
or damaged.
• Use only sockets and accessories in appropriate
sizesandensuretheytsecurely.
• Useonlyttingswith1/4”NPT(CP35205)and3/8”
NPT(CP35210,CP35215)thread.
• Use only impact sockets and impact attachments
with the tool. Hand sockets and attachments can
shatter and become dangerous projectiles when
used with impact tools.

6
People. Passion. Quality.
Coupler Regulator
1/2” or Larger Pipe
and Fittings
Leader Hose Plug
Drain Valve
Filter
OIL DA ILY
• The recommended air supply system setup is in
the diagram below.
• Do not exceed 90 PSI air pressure. Exceeding the
rated air pressure will reduce the useful life and
cause damage to the tool. Abnormally high air
pressure can also cause the tool to explode.
• Install an air check valve and/or safety cables to
prevent hose whipping in the event of hose or
coupler failure.
• Installairshutovalvessotheyarewithinreach
at all times.
• Install a lter/regulator/lubricator module to
supply clean lubricated air. Drain the accumulated
water from the air tank daily. Eliminating moisture
and dirt passing through the air system is essential
formaintainingthelongevityandperformanceof
the tool.
• Use a leader hose to connect the air hose to
the tool. The leader hose reduces vibration to
couplers and enhances exibility and safety. Do
not use quick connect coupler to connect the air
hosetothetool.Thevibrationsfromoperatingthe
tool will damage the coupler.
• Use only ttings with 1/4” NPT thread (CP35205)
and 3/8” NPT thread (CP35210, CP35215) to
connect to the tool.
Air Supply system installation
USage Instructions

7
www.capritools.com
• Lubricatethetoolbeforerstuse.
• Lubricate the tool daily as well as before and after
each use.
• Lubricate the tool before storage.
• Moisture in the air supply degrades components
andcreatesrustwithinthetool,whichnegatively
aects its performance. Daily lubrication is
necessary to maintain proper operation of the tool.
Failure to do so will reduce the tool’s useful life and
voidthewarranty.
To lubricate the tool:
1. Wear eye and ear protection.
2. Turnotheairsupply,depressthetriggertorelease
residual air, and disconnect the air line from the
tool.Removeanysocketsandattachments.
3. Face the air inlet upwards, depress the trigger, and
place 1 teaspoon of 10W air tool oil into the air
inlet.
4. Reconnectthetooltotheairsupply.Runthetool
forseveralsecondstoallowtheoiltocirculate.Do
not point the exhaust at yourself or anyone else.
Excess oil will exit from the exhaust and should be
captured with a shop towel.
Before you begin:
• The impact wrench is designed for tightening and
loosening threaded fasteners. Use the tool only for
intended purposes.
• Drain the air tank.
• Lubricate the tool.
• Use only sockets and accessories in appropriate
sizesandensuretheytsecurely.
• Use only impact sockets and impact attachments
with the tool.
• Always wear proper personal safety equipment.
• Keep yourself well balanced with proper footing at
all times.
• Keep your hands dry, clean, and free from oil and
grease.
• Use only up to 90 PSI air pressure.
Operation:
• Ensure forward/reverse is in the desired position
before starting the tool.  Provide sucient rear
clearance before loosening fasteners.
• Use the power dial to select desired power setting
(2settingsinforwardand1settinginreverse).
• Depress the trigger to use the tool, and release the
trigger to stop.
• Keephandsandbodyawayfrommovingparts.
• Lay the tool down only when it completely stops
moving.
• Turn o the air supply, depress the trigger to
release residual air, and disconnect the air line
from the tool each time before changing sockets
and attachments.
• Turn o the air supply, depress the trigger to
release residual air, and disconnect the air line
from the tool when the job is completed.
• Lubricate the tool before storage.
lubrication Usage

© Capri Tools
Capri Tools will repair, without charge, any defects
due to defective materials or workmanship
for two (2) years from the date of purchase,
applicable to the original purchaser only and
proof of purchase from an authorized retailer is
required. The complete product must be returned,
freight prepaid by the original purchaser, to Capri
Tools. In lieu of repair, Capri Tools may provide
a replacement of a new product, a refurbished
product or a refund in its sole discretion. This
warranty does not cover normal wear and tear,
and does not apply where the tool has been
abused, misused or improperly maintained,
where repairs have been made or attempted
by others, or where any alterations have been
made to the tool. The determination of whether
theproductreturned to Capri Tools satises the
condition of this warranty shall be made by Capri
Tools in its sole discretion. The warranty does not
apply to accessories.
Capri Tools makes no other warranties,
expressed or implied, concerning the product of
the merchantability for tness thereof for any
purpose.InnoeventshallCapriToolsbeliablefor
anyindirect,incidental,punitiveorconsequential
damages arising from the sale or use of the
products sold hereunder. This limitation applies
both during and after the terms of the warranty.
This warranty applies only to products purchased
and used in North America. This warranty gives
you specic legal rights, and you may also have
otherrightswhichvaryfromstatetostate.
2 year limited warranty
Forfurtherdetailsonourwarrantycoverage,
PleasecontactourCustomerService.
CUSTOMER SUPPORT
[phone]
[email protected]
capritools.com