Carbex i-BRUSH 2.0 User manual

Safety and
Operator’s Manual
– HMI Display
i-BRUSH 2.0
Revision 1.0

NOTES IN DOCUMENTATION
This documentation is intended to give an overall description of the system. It is
essential that the documentation is followed when installing and commissioning the
system. The responsible staff must ensure that its properly and safety installed
following all the relevant laws, regulations’, guidelines and standards.
Disclaimer
The system described in this document is constantly under development. Carbex
reserve to right to add/change this documentation without prior announcement.
Trademarks
i-BRUSH® is a registered trademark.
Patent Pending
Patents & patent applications, see:
www.carbonbrushsolution.com/patents
TABLE OF CONTENTS
Safety instructions 4
Transport 4
Product overview 5
Interface description 6
Installation 8
Maintenance 9
Support and service 11
32 CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY | REVISION 1.0 REVISION 1.0 | CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY

■Never open the i-BRUSH box.
■The i-BRUSH system is designed to be mounted
indoors or in closed compartments. Any other
use will void the warranty.
■Moisture can form during transport in cold
weather or in the event of large temperature
fluctuations.
■Avoid moisture formation (condensation) in the
i-BRUSH system and leave it to adjust to room
temperature slowly.
■If condensation has occurred, wait at least 12
hours before switching on the i-BRUSH system.
The system need always to be packed in the
original packing when transporting. Mechanical
stress and strong vibrations should be avoided.
SAFETY
INSTRUCTIONS
WARNING SYMBOL FOR GENERAL DANGER
WARNING SYMBOL FOR ELECTRICAL DANGER
PRODUCT
OVERVIEW
PRODUCT ID
Supply voltage
IP Enclosure rating
Dimensions
Weight
Operating temperature
Storage temperature
HMI display cable
Display size/resolution
100 – 240 VAC (1,8 A)
IP54
380 x 300 x 182 mm
≈ 10,2 kg
0 – +55 °C
-20 – +70 °C
Up to 100 m
12.1-inch display 1280 x 800
TRANSPORT
SHORT CIRCUIT DUE TO MOISTURE
STANDARD
ACCESSORIES DESCRIPTION WEIGHT DIMENSIONS OPERATING
TEMPERATURE
I-2BR-SMS-
BARSCANNER
C37 USB ≈ 90 g 60 x 79 x 170 mm 0 – +50 °C
I-2BR-SMS-HMI-PEN Touch pen ≈ 11,3 g 8 x 130 x 8 mm 0 – +50 °C
I-2BR-1018-US Main cable US IEC
60320 C13 Socket
≈ 150 g Cable length: 2 m -20 – +60 °C
I-2BR-1018 Main cable PE contact
EU C13-Socket
≈ 150 g Cable length: 2.5 m -20 – +60 °C
54 CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY | REVISION 1.0 REVISION 1.0 | CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY

INTERFACE
DESCRIPTION
AC Power entry
module
HMI Display
connection (RJ45)
USB A Connection
(Reserve)
USA A Connection
(Barcode Scanner)
Display
Door lock
OVERVIEW FRONT PANEL iBRUSH DISPLAY BOTTOM PANEL
76 CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY | REVISION 1.0 REVISION 1.0 | CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY

INSTALLATION
The i-BRUSH Display should be mounted within
100 meters of the i-BRUSH system. The i-BRUSH
Display should be securely fastened.
■Connect the i-BRUSH Display to 110 – 230
VAC (1,8 A). Make sure that it is connected to
ground via the power cord.
■Connect the barcode scanner to the
corresponding connector.
■Connect the RJ45 cable from the i-BRUSH
system to the corresponding connector on the
i-BRUSH Display.
Make sure the i-BRUSH Display is turned off
before making any connections to it.
OPERATION
To power up the i-BRUSH Display push the on/off
button on the power entry module.
After some seconds it will show the HMI.
NOTE!
CLEANING DANGER
The I-BRUSH system does not require any special
maintenance. If the system stops working, do not
try to repair it or open it. Doing so will void the
warranty.
A broken system should in most cases be returned
to Carbex for repair – always contact Carbex first
and they will advise on the action to take.
Switch off the device and all connected devices, and
disconnect the device from the power supply.
The device can be cleaned with a soft, damp cleaning
cloth. Do not use any aggressive cleaning materials,
thinners, scouring material or hard objects that could
cause scratches.
SPARE PARTS LIST I2BRHMISMS1000
COMPONENT CARBEX ITEM NUMBER
DC supply I-2BR-HDR-60-24
Fuse I-2BR-1011
Display I-2BR-HMI-MONITOR
Touch pen I-2BR-SMS-HMI-PEN
Barcode scanner I-2BR-SMS-BARSCANNER
MAINTENANCE
WARNING SYMBOL FOR
ELECTRICAL DANGER
98 CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY | REVISION 1.0 REVISION 1.0 | CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY

FAULT
CHECKLIST
SUPPORT &
SERVICE
FAULT ACTION
No power Check power supply, Check the fuse inside the cabinet.
Display is blank Check the connections and the cabling, check that the i-BRUSH box is
on. Check that the on/off button on the power entry module is ON.
The touch function is out of
order
Follow instructions to properly clean display.
Barcode scanner is not
working
Check the connections. Check also that the barcode scanner is lights
are red when pushing the button, replace if not.
CARBEX SUPPORT
[email protected]
CARBEX HEADQUARTERS
Kvarnbacksvägen 12
SE-592 41 Vadstena
Sweden
Phone exchange:[phone]
E-mail: [email protected]
OPENING HOURS
Monday – Thursday
07:30–16:30 (7:30 am – 4:30 pm)
Friday
07:30–14:00 (7:30 am – 2:00 pm)
1110 CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY | REVISION 1.0 REVISION 1.0 | CARBEX SAFETY AND OPERATOR’S MANUAL – HMI DISPLAY

CARBEX AB
BOX 115, SE592 22
VADSTENA, SWEDEN
PHONE
[phone]
WEB
carbonbrushsolution.com
MAIL
[email protected]
BEYOND THE BOUNDARIES OF BRUSH TECHNOLOGY
I-BRUSH 2.0 SAFETY AND OPERATOR’S MANUAL – HMI Display
Revision: 1.0
i-BRUSH is designed and developed by
Carbex AB, Vadstena, Sweden.