Casa TSP730 User manual

Installation Manual
fully automated
floor heating thermostat
with towel rail control
t/r control
16A
rated
220-
240
VAC
CASA-TSP730
Touch Screen
Programmable Thermostat
Touch screen
3 operating modes
7 day programmable
Towel rail control
Air and floor sensor

Fitting Instructions
Separate the backplate from the unit. Use machine screws to securely attach 1.
the backplate to the wall.
Follow the Wiring Diagram to connect the floor heating cold leads, optional 2.
t/rail power leads, exterior temperature sensor and electrical supply to the terminals.
Re-attach the unit to the wall-backplate ensuring that 3 plastic clips are clicked correctly.3.
Note:
Thermostat connection must be
done by registered electrician.
Wiring Diagram
towel rail
3A
2

Setting the Time and Day
Short press key to enter the setting mode and the “clock” starts to blink.
Short press key to enter the clock setting mode and the “week” starts to blink.
Using and set the day in the week. Press to confirm and move forward to
set the clock. Repeat same steps to set hour and minute. Press to come back to
main screen.
Programming floor heating
This heating thermostat is pre-programmed with default settings for floor heating and
towel rail.
Default Settings
(Floor Heating)
Morning
Afternoon
ON
ON
OFF
OFF
Time Time
Temp Temp
6.00am
6.00pm
6.00am
6.00pm
8.00am 8.00am
10.00pm 10.00pm
26 C
15 C
26 C
15 C
26 C
15 C
26 C
15 C
Monday - Friday Saturday - Sunday
MENU
MENU
CLOCK
DONE
DONE
ESC
To edit default settings simply press key to enter the programming mode.
or starts to blink. Use and keys to choose floor heating programming
mode or towel rail programming mode . Press to choose/confirm.
Using and keys choose day in the week, press to confirm and move forward.
Choose Mon - Fri schedule for heating. Choose start time (1), followed by heating
temperature (Default 26 C), then heating stop time (2), followed by stand by temperature
(Default 15 C). Repeat same steps for evening schedule. Press to choose/confirm.
Repeat same steps to setup Saturday and Sunday schedule.
Press several times to comeback to main screen.
Program
Default Settings
(Towel Rail)
Morning
Afternoon
ON
ON
OFF
OFF
Time Time
6.00am
6.00pm
6.00am
6.00pm
8.00am 8.00am
10.00pm 10.00pm
Monday
Friday
Saturday
Sunday
DONE
DONE
DONE
ESC
Manual Mode for Floor Heating
If you wish to manually operate your heated floor simply press Au/Ma key .
This will switch heating in Manual mode. Use and keys to set desired
temperature. To go back to Auto mode press Au/Ma key again.
To switch ON and OFF thermostat long press power button .
Au/Ma
Au/Ma
3

Screen Lock
Press and hold the and key together for 3 seconds to lock thermostat screen
and prevent modification of the thermostat's settings. A pad-lock symbol will be displayed.
Repeat same action to unlock it.
Default Settings
Short press “Default” key to recover Factory Defaults.
Factory Reset
Short press “Reset” key to reset thermostat.
Casa Group Ltd, PO Box 35353, Browns Bay, Auckland
Free Call: 0800 00 22 72, [e-mail]
www.casaheating.co.nz
Advanced Settings (Functions F0 - F4)
Advance settings mode allow you to fine tune your controller.
To access advance settings long press and together for 3 seconds.
Use and keys to select desired function and to enter or confirm your choice.
Below is the list of advanced setting functions and available options.
Orange coloured represent default values.
F0 - Temperature Calibration
Calibrate temperature from -15 C0
F1 - Sensor Choice
2 - External sensor (in floor)
- Internal sensor (in unit)1
0 - Combined internal and external sensor
F2 - Program Backup Function
0 - Backup not active
- Backup Active1
F3 - Temperature Control Band
When desired temperature is achieved controller will switch off
heater and start again when temperature drops.
Choose between 1, , or 3 degrees 2
F4 - Choose Manual or Auto mode for towel rail
ON - Manual mode only
Auto mode with manual override OFF -
DONE
MENU