CATCHPOLE & RYE The Mercantile Wall Mounted User manual

INSTALLATION GUIDE
PHONE: [phone]
EMAIL:[e-mail]
ADDRESS:CATCHPOLE & RYE, SARACENS DIARY, ASHFORD, KENT, TN27 0SA WWW.CATCHPOLEANDRYE.COM
©COPYRIGHT 2021 CATCHPOLE & RYE.
ALL RIGHTS RESERVED.
e Mercantile Wall Mounted Towel Rail
STANDARD, DUAL FUEL & ELECTRIC MODELS
YOU WILL NEED
- Pair of Radiator valves for Dual Fuel or Standard Models (sold separately).
- Screwdriver
- Pipe Cutter
- Spanner
- 15mm Olive
- Suitable PTFE Tape
GENERAL INFORMATION
This product is manufactured entirely in the UK and has been rigorously tested to provide many years of good service when
installed by a suitably qualified professional.
All products must be thoroughly inspected once upon delivery and again prior to installation. Carefully remove the product packag-
ing for the initial inspection and repackage if being stored. It should be stored in a clean dry and safe environment at normal room
temperature.
Please read these instructions carefully before commencing any work and ensure that all parts are present and in perfect condition
before starting the installation.
If you require assistance or have any questions please call our Technical department: 01233 840 840
or email: [email protected].
COMPONENTS
1. Pre Assembled Towel Rail
2. Cable Shroud Assembly
3. Radiator Valve Body x2
4. 1 1/2” Fixing Screws
5. 15mm Olive

After the towel rail has been thoroughly inspected and
carefully unpackaged measure the fixing points on the wall
and floor, ensuring that the rail is level and aligned with the
incoming feeds or electric supply where applicable. Whilst
every effort is made to maintain the orientation of each foot,
we cannot guarantee this, therefore it is imperative that each
screw position is marked out before assembly.
Ensure that there are no wires or pipes behind the marked
locations for the fixings. Drill holes for fixings.
Insert plugs.
SECTION 1: Wall Fixings - Applies to all models
NEXT STEPS:
For electric and dual fuel models continue to SECTION 2.
For Standard models skip to SECTION 3.
INSTALLATION GUIDE
PHONE: [phone]
EMAIL:[e-mail]
ADDRESS:CATCHPOLE & RYE, SARACENS DIARY, ASHFORD, KENT, TN27 0SA WWW.CATCHPOLEANDRYE.COM
©COPYRIGHT 2021 CATCHPOLE & RYE.
ALL RIGHTS RESERVED.
e Mercantile Wall Mounted Towel Rail
STANDARD, DUAL FUEL & ELECTRIC MODELS

SECTION 2: Connecting to central heating systems - Applies to Standard and Dual Fuel Models.
2.
4.3.
1.
Ensure that the 15mm feed pipes are aligned correctly for
fitting to the radiator valves. For the best fitting we recom-
mended that approximately 16mm of pipe is proud of the wall
and each pipe is located approximately 85mm directly below
the center point of the lower foot.
Fit the radiator valve tail thread using an appropriate allen
key, use an appropriate PTFE tape on the thread. DO NOT
OVER TIGHTEN. Then loosely attach the radiator valve.
Position the escutcheon and pipe cover over the feed pipes. Attach the rail to the wall using the wall plugs installed in
section 1.
INSTALLATION GUIDE
PHONE: [phone]
EMAIL:[e-mail]
ADDRESS:CATCHPOLE & RYE, SARACENS DIARY, ASHFORD, KENT, TN27 0SA WWW.CATCHPOLEANDRYE.COM
©COPYRIGHT 2021 CATCHPOLE & RYE.
ALL RIGHTS RESERVED.
e Mercantile Wall Mounted Towel Rail
STANDARD, DUAL FUEL & ELECTRIC MODELS

SECTION 2: Connecting to central heating systems - Applies to Standard and Dual Fuel Models.
Attach the feed pipes to the radiator valves using the
compression olives and nuts.
Position the escutcheon and pipe cover so that they are in
the desired location. These are push fit.
Fill the radiator and bleed using the bleed valve located
under the upper left joint when looking directly at the rail.
For standard models test the towel rail. For dual fuel models
continue to section 3.
INSTALLATION GUIDE
PHONE: [phone]
EMAIL:[e-mail]
ADDRESS:CATCHPOLE & RYE, SARACENS DIARY, ASHFORD, KENT, TN27 0SA WWW.CATCHPOLEANDRYE.COM
©COPYRIGHT 2021 CATCHPOLE & RYE.
ALL RIGHTS RESERVED.
e Mercantile Wall Mounted Towel Rail
STANDARD, DUAL FUEL & ELECTRIC MODELS

SECTION 3: Connecting to power supply - Applies to Standard and Dual Fuel Models.
*Applicable to electric model. Attach the rail to the wall using
the wall plugs installed in section 1.
Ensure that the wire shroud is the correct size, the tube can
be cut to size. Then feed the cable through the pipe.
Connect the cable to the element in the towel rail then fit the
shroud to the towel radiator.
For electric models, test the rail.
IMPORTANT: Electric elements should be fitted only by a
suitably qualified electrician and must be earthed and
connected to a cable outlet in the bathroom in accordance
with I.E.E wiring regulations. The electrical connection
should be made to a 5-amp fused fixed spur located outside
the bathroom.
INSTALLATION GUIDE
PHONE: [phone]
EMAIL:[e-mail]
ADDRESS:CATCHPOLE & RYE, SARACENS DIARY, ASHFORD, KENT, TN27 0SA WWW.CATCHPOLEANDRYE.COM
©COPYRIGHT 2021 CATCHPOLE & RYE.
ALL RIGHTS RESERVED.
e Mercantile Wall Mounted Towel Rail
STANDARD, DUAL FUEL & ELECTRIC MODELS